Question about 2006 Nissan Altima

1 Answer

Changing oa a battery

All I want to do is change my battery can you tell me how? So far I have the negative post disconnected. The positive post is loosened but will not come off. What is wrong?????????

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 51 Answers

You may need to use a battery terminal puller. It has a clamp that clamps around the connector, and a threaded post in the center. as you turn the threaded post, it will lift the terminal connector straight up (like a corkscrew pulling a cork out of a wine bottle). You can also make sure the connector is completly loosened, and try pulling the connector straight up by holding both sides of the connector and applying equal force while pulling. I've also had success by wiggling (rocking) the connector while pulling straight up. Don't be afraid to use a little muscle.

Posted on Aug 12, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Kawasaki wiring diagrams

Black is always negative no matter what color stripe it has.

Aug 18, 2014 | Cars & Trucks

1 Answer

After changing the battery there is no heat or air

When you change the battery, you should take off the negative
pole first and then disconnect the positive pole. wait at least 30 min and connect the positive pole first and the negative last.
Sometimes you have to drive your vehicle at least 10 miles so the car computer will acknowledge the change.

Apr 24, 2014 | 2007 BMW X5 3.0si SAV

1 Answer

How to change the battery on 2001 buick regal

open hood
locate battery
disconnect positive wires from post
disconnect negative wires from post
pull out old battery

put in new battery
reinstall wires to posts

Jan 03, 2011 | 2001 Buick Regal

1 Answer

When changing the battery on a 2006 530i BMW, does the car need to be reprogramed for the new battery and how do you do it?

Loosen the battery anchoring. Start the car before disconnecting the battery, Remove Negative first, then the positive. Be very careful and insulate the positive terminal once it is removed so it doesn't come in contact with ground or the negative terminal! Replace the battery, reconnect the terminals (positive first) and then re-anchor the battery to the car. If you follow these instructions, you will not need to re-program your car.

Nov 24, 2010 | 2006 BMW 5 Series

2 Answers

Do i disconnect the red negative or black positive battery cable first when i am changing my 04 cooper battery?

Always disconnect negative first. Also, when you're putting them back on, connect negative last.

Oct 27, 2010 | 2004 Mini Cooper

1 Answer

Changing throttle position sensor on a 2004

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the throttle position (TP) sensor electrical connector.
  3. Remove the screws and the TP sensor.

Throttle position (TP) sensor electrical connector

TP sensor

To install:
  1. Install the screws and the TP sensor. Tighten screws to 7 inch lbs. (3 Nm)
  2. Connect the throttle position (TP) sensor electrical connector.
  3. Connect the battery ground cable.

Apr 25, 2010 | 2004 Ford Taurus

1 Answer

With battery ground disconnected and positive connected if i take a voltage tester and touch from battery ground to chassis ground i get 12.52 volts, just what the battery tests,+ to -.

Are you sure you were touching the negative post and not the positive post. If you checked the positive post and the other wire to body chassis then you should get the reading you say here. Negative to negative is negative and you should have had no reading at all. Please do this test again being absolutly posative your touching the negative post. There will be a - sign on the battery under that post. Get back to me after the double check, Raz

Apr 18, 2010 | 1996 Mercury Mystique

2 Answers

How to unhook battery

disconnect the negative first, then the positive cables, 8mm or 5/16" socket. the block that hold the battery down is 13mm

Oct 17, 2009 | 1995 GMC Suburban

1 Answer

What to do to change battery

hi!... it's safer to remove the ground first or the negative post. then next the positive post... upon changing install positive then the negative... hope i helped

Aug 02, 2009 | 2000 Chevrolet Monte Carlo

Not finding what you are looking for?
2006 Nissan Altima Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

64052 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides