Question about 1999 BMW 323 Series

4 Answers

Keyless entry won't work

I have 2000 323CI and my keyless entry won't work. When I press the buttons, nothing happens. the fuel door locks when the door is manually locked. The doors will lock when manually locked but not when the keyless entry remote is pressed.

Posted by on

  • 3 more comments 
  • hodges_tracy Aug 11, 2008

    It's not that. the remote battery recharges everytime the key is used to start the car.

  • hodges_tracy Aug 12, 2008

    It's the new key that is triangular shaped. I tried to reprogram the key and thought maybe the key died. I ordered a key key from BMW and that's how I found out that the key recharges itself and that there was something else wrong because the new key didn't work after the dealership programmed it.

  • alison blake Sep 26, 2008

    I just purchased a 1999 323i 5 door and was given only one key. the remote won't work. I went to Halfords to purchase a replace battery but they said that if I insert it incorrectly I could immobilise the car! As I haven't even got a handbook or spare key for this car, I'm afraid to risk that. I'm not sure wether to purchase a new key from a bmw dealer (at great expense I suspect) or just put up with opening it manually, any advise?

  • Anonymous Mar 13, 2014

    2000 Camry. The door lock/unlock remote will not lock or unlock the driver's door and I have to push it several times to unlock/lock any of the other doors.

  • Anonymous Mar 13, 2014

    2000 Camry. the remote door lock/unlock stopped working on driver's door only.

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

I have a 1999 BMW E46 I have had a problem with the keyless entry myself. I brought the car to BMW Dealer and they told me that my Lock had an issue and that they need to repair some wiring wich would cost me $1,023.98 to find out that it was a fuse that burned out. I have replaced the 5 amp fuse with another one but it burned the fuse again so I put a 10 amp fuse and i have not had a problems since. In my car is fuse # 54 if Im not mistaken. But waht you can do is open the fuse box which is located in your glove compartment look for a diagram that shows you which fuse is where it will give you a fuse name a number where the fuse is located and how many amps fuse it is.

Posted on Dec 23, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You need to reprogram your remotcontrol by doing this
1, turne the ignation on and trun it off
2, prassed and hold the unlock botten and prasse 3 time the open botton
3, relesed all botten then the door well open and closed normal

Posted on Dec 12, 2008

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi mesafnt i had the same trouble with a 04 318ci i tryed you solution this fix my key thank you

Martin

Posted on Apr 05, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 60 Answers

Try changing the battery in your remote

Posted on Aug 11, 2008

  • steve dbo Aug 11, 2008

    is it a new or old clicker have u tried getting it reprogrammed i found a web site that has info on reprogramming remotes so other than this i have no idea - good luck



    (This is for the 96+ alarms)

    Straight out of the book:

    Preparation
    1. Close all doors, trunk, and hood.
    2. The security system must be in 'disarm' mode. The key must be removed from the ignition key slot.

    Enter Code-Learning Mode
    3. Open the trunk and leave it open
    4. Open the driver's door and sit in the driver's seat.
    5. Close the driver's door.
    6. Cycle the ignition switch five times between the 'OFF' position and position 2, (ignition 'ON', all dash warning lamps will illuminate). The red status LED will illuminate continuously, and the siren will 'chirp' once, to indicate that the code-learning mode has been initated.

    Do not start the engine.
    The ignition switch cycling in step #6 must be preformed within 45 seconds.


    Register/Delete ID Code(s)
    7. Open the driver's door, (remain seated in driver's seat).
    8. Close driver's door.
    9. Press and release any button on the remote you wish to register into the system. The status LED will shut off momentarily to indicate that one ID code has been registered.
    10. Repeat steps 7 through 9 to register the remaining three ID codes.

    It is possible for the system to memorize a total of four different ID codes. As a new code is initalized into memory, the oldest code in memory is automattically deleted. If you had lost your remotes and wished to delete the lost remote ID codes from memory, you could initialize the ID code from a newly purchased replacement transmitter four times thereby deleteing the previous ID codes from system memory.

    Exiting Code-Learning mode
    11. Open driver's door, and exit from vehicle, leaving the door open.
    12. Close trunk.
    13. Close driver's door. The LED will turn off and the siren will 'chirp' twice.
    14. The initalization procedure is now completed; test all remotes to confirm operation.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Volkswagen Jetta keyless entry & lock problems


If the system is not working even when you press the buttons on the door, then the problem is not with the remote control. I would first check if all the fuses are ok, if they are, I would check the wiring on the door to make sure there are no wires broken of chaffed. Focus first on getting the system working with the door buttons and after that is ok, the move on to the keyless system in case it still does not work. Hope this helps.

Dec 29, 2017 | 2002 Volkswagen Jetta TDI

1 Answer

I have a 2000 ford mustang. Suddenly my keyless entry remote stopped working. I replaced the battery and turned the off and on 8 times and the locks cycled. after which i pushed the unlock but nothing...


The keyless entry system is controlled by the (GEM) - generic electronic module .
Keyless Entry The electronic door lock system has two main components:
  • generic electronic module (GEM)(14B204)
  • keyless entry remote transmitter (15K601)
  • NOTE: Battery power and ground must be remove before disconnecting the GEM connectors to avoid setting false codes.
    Power Locks Operation The power locks feature allows the customer to lock and unlock the doors via momentary switches located on the driver and passenger door. When the GEM detects a momentary press of the driver or passenger lock button, the GEM will supply power to the driver or passenger lock actuators for approximately 250 ms from relays internal to the GEM. When the GEM detects a momentary press of the driver or passenger unlock button, the GEM will supply power to the driver or passenger unlock actuators for approximately 250 ms from relays internal to the GEM.
    Remote Keyless Entry Door Locks Operation The remote entry feature allows the customer to unlock the driver door, unlock all doors, and lock all doors using a valid remote transmitter as long as the ignition switch is not in RUN or START. The driver door is unlocked whenever the GEM detects a valid remote transmitter unlock transmission. All the doors are unlocked when the GEM detects a second valid remote transmitter unlock transmission within three seconds of the first transmission. All the doors are locked when the GEM detects a valid remote transmitter lock transmission. If the GEM detects a second valid remote transmitter lock transmission within three seconds of the first transmission, the doors will lock again, the horn will sound for 20 ms and the parking lamps will flash for 200 ms to indicate the doors are locked. If the GEM detects the driver or passenger door is ajar during the second lock transmission, the doors are locked again and the horn is sounded twice. If the GEM detects a valid remote transmitter lock transmission within three seconds of detecting a valid remote transmitter unlock transmission, the GEM will lock all the doors
    • The doors do not lock/unlock using the remote transmitter
    • Ignition switch.
    • GEM.
    • Remote transmitter.
    • Remote transmitter batteries.
    • GO to Pinpoint Test C .
    You followed the program instructions to the letter ? Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
    NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
    NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
    1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
    1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met.
      Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
    1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
    1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.
    1. Take an have the vehicle checked for DTC'S
B1396 Power Door Lock Circuit Short to Battery GEM GO to Pinpoint Test B . B1397 Power Door Unlock Circuit Short to Battery GEM

Apr 12, 2017 | Ford Mustang Cars & Trucks

1 Answer

I have a 96 ford conversion van with a 600 plus addon keyless system and need to program new keyless remots , need to know how to get system in program mode.


Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

Nov 28, 2010 | 1996 Ford Econoline

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

How do i reprogram electronic door locks


Programming Electronic Door Lock Control System NOTE: The electronic door lock control processor (14B001) erases all previous keyless entry remote transmitter (15K601) from memory when the keyless entry remote transmitters are programmed or reprogrammed. The electronic door lock control processor can store up to four keyless entry remote transmitters in memory.


  • To program (or reprogram) keyless entry remote transmitter into the electronic door lock control processor, perform the following steps:
  1. Turn ignition switch to the RUN position and momentarily short the two terminals of the program connector taped to the wire assembly and located behind the glove compartment. All doors should lock and then unlock. Remove shorting pin.
  1. Press any button on keyless entry remote transmitter. All doors should lock and then unlock to verify the keyless entry remote transmitter has been programmed. If door locks do not respond, press button again (up to three times maximum with the same keyless entry remote transmitter).
  1. Repeat the above step to program additional keyless entry remote transmitters into the electronic door lock control processor (up to four keyless entry remote transmitters maximum).
  1. Turn ignition switch OFF. All doors should lock and then unlock.
  1. Check operation.

Jun 05, 2010 | 1997 Ford Windstar

1 Answer

Keyless entry on honda civic 2006 not working


The keyless entry is designed to work with the doors closed (closed - not locked). If the door ajar sensor thinks the door is open the keyless entry is disabled. When you manually lock the door it might tighten the door just enough to activate the keyless entry. I would try slamming all the doors closed and then see if the keyless entry works. If it still wont work have the wiring checked on the front door lock.

May 12, 2009 | 2006 Honda Civic Hybrid

2 Answers

1999 lincoln con


SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
  1. Enter the new five-digit keyless entry keypad code.
  1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
  1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
  1. After all new keyless entry codes are programmed:
    • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
    • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
    • -------------------------------------------------------------
Programming —Transmitter
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------
Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
  1. Press the SET button on the driver door panel.
  1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
  1. Press the 1 or 2 memory button on the driver door panel.
-------------------------------------------------------------
Programming —Autolock and Horn Chirp
  1. NOTE: This procedure must be completed within 30 seconds.
    Turn the ignition switch to RUN.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to OFF.
  1. Press the UNLOCK button three times.
  1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
  1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
  1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
----------------------------------------------------------------------------------

Apr 07, 2009 | 1999 Lincoln Town Car

2 Answers

My remote for the keyless entry does not work.


does trunk button work? panic button?
here's 2003 info:


  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter.
  • Driver door module (DDM).
  • Go To Pinpoint Test G .

SECTION 501-14: Handles, Locks, Latches and Entry Systems 2003 Town Car Workshop Manual
GENERAL PROCEDURES Remote Transmitter Programming
  1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming that the program mode has been entered.
  1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
    Press any button on the transmitter to be programmed.
  1. If additional keyless entry remote transmitters are to be programmed, repeat Step 2 within 7.5 seconds.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
--------------------------------------------------------------
report back

Mar 22, 2009 | 2004 Lincoln LS

1 Answer

96 sable wagon keyless entry


Try re-programing the system.
These are the instructions from the service manual.

. Turn ignition from OFF to RUN 5 times within 10 seconds, with the 5th time ending
in RUN. Door locks will cycle to confirm programming mode.

2. Within 20 seconds press any button on first keyless remote. Door locks will cycle
to confirm programming.

3. Within 20 seconds, press any button on second keyless remote. Door locks will
cycle again to confirm programming.

4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

Mar 02, 2009 | 1996 Mercury Sable

3 Answers

Keyless entry


I believe dealer has to re-program the new code.

Aug 29, 2008 | 2001 Ford Explorer Sport Trac

Not finding what you are looking for?
1999 BMW 323 Series Logo

2,412 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

stephen Kiarie
stephen Kiarie

Level 1 Expert

32 Answers

Roy Cunningham

Level 1 Expert

35 Answers

vince

Level 3 Expert

1234 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...