Question about 1993 Chevrolet Camaro

1 Answer

What is the easiest way to get the starter out of a 1994 Camaro? Do I have to remove other parts to get to it??

Posted by on

  • Anonymous Mar 31, 2014

    I have the starter out but the starter doesnt clear exhaust and cross suport. on the 93 camaro what is the easiest peice to remove or loosen to make room to pull the starter and put the new one back in.



1 Answer

Drop ur exaust pipes is the easiest way.

Posted on Aug 18, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will a tahoe or blazer or suburban starter interchange witb 1994 chevy camaro 350

try it and see would be the easiest way as there are a few too many varients to say yes or no

Apr 22, 2014 | Cars & Trucks

2 Answers

No oil pressure

Are you certain it is the oil pump? Have you checked the actual oil pressure with a guage? There are other things that could cause low oil pressure, such as the pressure relief valve. I would get a manual on the car. This should tell you all you all you need to know, including how to change the oil pump, if that is indeed necessary. I'm not certain if you can pull the pan on that car without pulling the engine. Some you can, but you have to support the engine while you remove the cross member. Again, a book will show you the easiest way. I hope I have been helpful.

Mar 29, 2014 | 1994 Chevrolet Camaro

1 Answer

How can I jump the starter on my 91 camaro?

hot wire starter you can short out ignition switch and wiring. to jump starter ignition switch start have to run 10 gauge jumper wire from the starter solenoid positive battery terminal to starter switch or S terminal on starter solenoid this procedure take two people but better remove starter replace starter solenoid. trying jumping off starter on camaro would be dangerous you have jack up car to get to starter and wiring person laying under car hot wiring starter while other person hold ignition start position put person under car in deadly position just remove starter have auto parts check it out first replace starter or solenoid if either bad. easier hot wire starter if starter under hood like my 1977 vega monza had starter at top could take long screw driver jump starter off.on the four cylinders engines back in the 70s. camaro starter under car dangerous trying to hot wire not a good idea.

May 07, 2013 | Cars & Trucks

1 Answer

Without cuttin a hole whats thw easiest way to change the fuel pump?

Hello: Drop (remove) the gas tank. If you cut a hole be careful......

Aug 21, 2011 | 1994 Chevrolet Camaro

1 Answer

I am completely removing the a/c system on my 1994 chevrolet camaro, What all needs to be removed?

As opposed to disassembling the front end and dashboard of the car and then trying to find replacement parts for a 17 year old car; how about just finding a bracket with a freewheel which will allow you to remove the A/C compressor. That way it could be refitted someday, but you could drive without wasting power to spin the compressor. I think those type of brackets are sold at parts stores.

Jan 23, 2011 | 1994 Chevrolet Camaro

1 Answer

How to change the starter from my 1994 chevy camaro

REMOVAL & INSTALLATION 3.4L and 1993-95 5.7L Engines
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. If necessary for access to the starter, disconnect the exhaust crossover pipe from the manifolds.
  4. Unfasten the two starter mounting bolts/screws and carefully lower the starter motor.

To install:

Before attaching the electrical connectors, tighten the inner nuts on the solenoid terminals. If the nuts are not tight, the solenoid cap could be damaged during installation of the leads. Tighten the inner nut of the "BAT" terminal to 80 inch lbs. (9 Nm).
  1. Fasten the electrical leads to the starter motor assembly. Tighten the solenoid switch "BAT" terminal outer nut to 80 inch lbs. (9 Nm) and the "S" terminal nut to 22 inch lbs. (2.5 Nm).
  2. Position the starter motor to the engine and install the retaining bolts/screws. Tighten to 35 ft. lbs. (47 Nm).
  3. Measure the starter pinion-to-flywheel clearance and add shims, if necessary.
  4. If removed, connect the exhaust crossover pipe to the manifolds.
  5. Carefully lower the vehicle, then connect the negative battery cable. Tighten the cable to 11 ft. lbs. (15 Nm).

Hope helps.

Sep 06, 2010 | 1994 Chevrolet Camaro

1 Answer

How to put a starter in a 1998 camaro

disconnect the battery.

remove the wire from the starter.

remove two bolts (probably 1/2 inch) from the starter

take to auto parts place - exchange for a rebuild.

bolt in the new starter

attach the cable

connect the battery

Apr 28, 2010 | 1998 Chevrolet Camaro

1 Answer

Were is the starter in a 1994 camaro

On the bottom, next to the oil pan on the passenger side

Apr 03, 2010 | 1994 Chevrolet Camaro

1 Answer

Need to replace starter on a 1986 Camaro, but cannot get the old starter past the exhaust pipe.

Removing the starter
  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Disconnect all wiring from the starter solenoid. Replace each nut as the connector is removed (as thread sizes differ from connector to connector). Note or tag the wiring positions for installation.
  4. Remove the bracket from the starter and the two mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.
  5. Remove the front bracket bolt or nut. Lower the starter front end first, and then remove the unit from the car.
These are the steps for removing the starter on the Camaro. Did you remove the bracket? Hope this helped and best wishes.

Aug 01, 2009 | 1986 Chevrolet Camaro

1 Answer

Power Steering Pulley for 1994 Chevy Camaro V6 manual

Yep, Their Right. A Salvage Yard is your Only Choice. although you can try They are here in OKC and carry a LOT of Classic Parts.

Jan 15, 2009 | 1994 Chevrolet Camaro

Not finding what you are looking for?
1993 Chevrolet Camaro Logo

Related Topics:

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides