Question about Daihatsu Charade

2 Answers

Water pump - Charade Daihatsu Cars & Trucks

Posted by on

  • 1 more comment 
  • osphil Aug 11, 2008

    is there a manual or images on line of how to change a water pump in a G200 CX charade

  • Anonymous Aug 20, 2008

    HELLO MI MOTOR IS 1000 TURBODIESEL AND THE MOTOR IS VERY HOT, IM NOT KNOW IN WHAT POSICION GO THEN TUBS OF TERMOSTATO IM THINK HAVE ONE PROBLEM IN IS LOCATION THANKS FOR YOU ASISTANCE

    MI DIRECCION IS PODAR-JARDINES@ADINET.COM.UY

  • krispher Oct 17, 2008

    hi y name is kris....i just had my charade 88 gt engine over whole and as i took it 4 a test drive the engine was to hot and plus the heat gauge almost went to max.....could anyone have an idea of what is rong....

    my car is a 3cyl, gti 1.0

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Check out daiclub.com I downloaded my manual for my daihatsu from there forum it was free, and for larger images you can try google images, at any rate both are free and are very helpful. I just changed out my water pump it was not a quick thing, but it is done!

Posted on Dec 17, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi..my name is jimmi fom indonesia. i have Daihatsu Charade Car 1984. but now i hve problem with mesin. i dont know exacly wht happen with my car.mesin un moving...starter problem..
please send me the sollusiton to my email : jimmi_pku@yahoo.com
thanks
acctyually i dnt know about the mesin...

Posted on Aug 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Water pump


Which engine?

  1. Drain the radiator

91192665


  1. Loosen the water pump pulley bolts.
  2. Remove the serpentine belt.

91192666
  1. Remove the water pump pulley bolts and pulley.
  2. Remove the water pump bolts, pump and gasket.
  3. Clean the water pump mating surfaces.
Installation Procedure
  1. Install the water pump gasket and pump.
91192667


  1. Install the water pump bolts. Tighten the water pump bolts to 89 inch lbs.

91192668
  • Install the water pump pulley and bolt until snug.
  • Install the serpentine belt.
  • Tighten the water pump pulley bolts. Tighten the water pump pulley bolts to 18 ft. lbs.
  • Fill the cooling system and purge of air.
  • Inspect for leaks.
  • Sep 27, 2012 | 2001 Oldsmobile Alero

    1 Answer

    How to tighten a water pump on a 1990 oldsmobile 88 royale


    For water pump replacement i suggest you to check the help link provided below.

    click the link below :----

    Water pump replacing procedure for all vehicles?

    http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
    ---------

    HOW TO REPLACE A WATER PUMP

    http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

    ------------------
    How to route Water Pump Belt for 1992 Oldsmobile ?

    http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

    ---------
    How to replace Water Pump on Car ?

    http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

    ---------
    How to Remove Water Pump?

    http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

    -------
    Where is Water Pump located ?

    http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

    -----------

    This will help. Thanks.

    Feb 14, 2012 | 1990 Oldsmobile Eighty Eight

    1 Answer

    How to replace water pump infiniti m35 2006


    For water pump replacement i suggest you to check the help link provided below.

    click the link below :----

    Water pump replacing procedure for all vehicles?

    http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
    ---------

    HOW TO REPLACE A WATER PUMP

    http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

    ------------------
    How to route Water Pump Belt for 1992 Oldsmobile ?

    http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

    ---------
    How to replace Water Pump on Car ?

    http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

    ---------
    How to Remove Water Pump?

    http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

    -------
    Where is Water Pump located ?

    http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

    -----------

    This will help. Thanks.

    Feb 12, 2012 | 2006 Infiniti M35

    1 Answer

    Replace a water pump on a 1992 mercury topaz 4 cylander


    For water pump replacement i suggest you to check the help link provided below.

    click the link below :----

    Water pump replacing procedure for all vehicles?

    http://technoanswers.blogspot.com/2011/11/water-pump-replacing-procedure-for-all.html
    ---------

    HOW TO REPLACE A WATER PUMP

    http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-water-pump.html

    ------------------
    How to route Water Pump Belt for 1992 Oldsmobile ?

    http://carbeltrouting.blogspot.com/2011/12/how-to-route-water-pump-belt-for-1992.html

    ---------
    How to replace Water Pump on Car ?

    http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-water-pump-on-acura-car.html

    ---------
    How to Remove Water Pump?

    http://technoanswers.blogspot.com/2011/12/how-to-remove-water-pump-on-toyota.html

    -------
    Where is Water Pump located ?

    http://technoanswers.blogspot.com/2011/12/where-is-water-pump-located-on-toyota.html

    -----------

    This will help. Thanks.

    Feb 04, 2012 | 1992 Mercury Topaz

    1 Answer

    Change the water pump


    • Tools Required
    • J 43651 Water Pump Holding Tool
    • Remove the thermostat housing.
    • Remove the water pump access plate from the front cover.
    • Remove the right hand fender liner.
      1. Important: A drain plug has been provided at the bottom of the water pump assembly for additional coolant drainage from the engine block and water pump.
      Drain the coolant from the water pump using the plug at the bottom of the pump.
      1. mportant: The water pump holding tool supports the sprocket and chain during water pump service. The tool must be used or the balance shaft must be re-timed.
      Install the J 43651 into position.
      1. Tighten the bolts on the water pump holding tool into the threads on the water pump sprocket.
      2. Install the access cover bolts that were removed earlier to secure the water pump holding tool to the front cover assembly.
      3. Remove the 3 inner water pump sprocket to water pump blots.
        1. Important: Be sure to remove both water pump bolts from the front of the engine block.
        Remove the 2 water pump bolts.
        Remove the rear 2 water pump bolts.
        1. Remove the water pump.
        2. Remove and discard the water pump O-ring seal.
        Installation Procedure
        1. Important: Prior to installing the water pump, read the entire procedure. This will help avoid balance shaft chain re-timing and ensure proper sealing.
        Install a NEW water pump O-ring seal.

        1. Important: A guide pin can be created to aid in water pump alignment. Use a M 6 m x 6 mm stud. Thread the pin into the water pump sprocket.
        Using the guide pin, align the pin with the water pump holding tool.
        1. Position the water pump against the engine block and hand tighten the water pump bolts.
        2. Notice: Refer to Fastener Notice.
        Install the inner water pump sprocket bolts. After 2 are snug, remove the guide pin and install the 3rd bolt.
        Tighten the bolts to 25 Nm (18 ft. lbs.).
        1. Tighten the water pump sprocket bolts last. Tighten the bolts to 10 Nm (89 inch lbs.).
        2. Remove the J 43651.
        3. Install the water pump access plate and bolts. Tighten the bolts to 10 Nm (89 inch lbs.).
        4. Install the right hand fender liner.
        5. Install the thermostat housing.



    Aug 29, 2011 | 2006 Pontiac Solstice

    1 Answer

    Replacing the water pump on 96 chevy S10,


    Water Pump Removal & Installation 2.2L Engine To Remove:
    1. Drain the cooling system.
    2. Remove fan assembly.
    3. Loosen the water pump pulley bolts.
    4. Remove or disconnect the following:
      • Drive belt gm-03-22-606.gif

      • Water pump drive pulley bolts
      • Water pump drive pulley
      • Radiator inlet hose clamp and hose from the water pump
      • Water pump mounting bolts gm-03-22-605.gif

      • Water pump
      • Water pump gasket
      gm-03-22-607.gif

    To Install:
    1. Clean the mating surfaces.
    2. Install or connect the following:
      • Water pump gasket
      • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
      • Water pump mounting bolts
        1. Torque to: 18 ft lbs (25 Nm)
      • Water pump pulley and bolts
        1. Torque to: 18 ft lbs (25 Nm)
      • Radiator hose and clamp
    3. Fill with coolant.
    4. Check for leaks.
    4.3L Engine To Remove:
    1. Drain the cooling system.
    2. Remove fan assembly.
    3. Loosen the water pump pulley bolts.
    4. Remove or disconnect the following:
      • Drive belt gm_truck_43_wppulley.gif

      • Water pump drive pulley bolts
      • Water pump drive pulley
      • Radiator inlet hose clamp and hose from the water pump
      • Water pump mounting bolts gm_truck_43_waterpump.gif

      • Water pump
      • Water pump gasket
    gm_truck_43_waterpump_gsk.gif

    To Install:
    1. Clean the mating surfaces.
    2. Install or connect the following:
      • Water pump gasket
      • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
      • Water pump mounting bolts
        1. Torque to: 30 ft lbs (41 Nm)
      • Water pump pulley and bolts
        1. Torque to: 18 ft lbs (25 Nm)
      • Radiator hose and clamp
    3. Fill with coolant.
    4. Check for leaks.
    prev.gif next.gif

    Feb 12, 2011 | 1997 Chevrolet S-10 Pickup

    1 Answer

    How long does it take to replace a water pump on Pontiac Aztec?


    It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
    Removal Procedure :
    techmecho.gif
    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.
    techmecho_0.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    techmecho_1.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    techmecho_2.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    techmecho_3.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks.
    4. That's it.

    Nov 18, 2010 | 2001 Pontiac Aztek

    1 Answer

    How to take off the water punp


    1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system

    Aug 13, 2010 | 2002 Buick LeSabre

    1 Answer

    How do you replace a water pump in an aztec?


    Notes Water Pump Replacement

    Removal Procedure
    3e77de9.gif

    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.


    c7273fb.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    c102468.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    f16e1fd.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    • 258f600.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks

    Jun 17, 2009 | 2001 Pontiac Aztek

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    264 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daihatsu Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Donald DCruz
    Donald DCruz

    Level 3 Expert

    17129 Answers

    Are you a Daihatsu Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...