Question about 1991 Toyota Pickup

1 Answer

Timing chain cover leak need a diagram of parts and bolts

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

Did you check the cam seal? can be replace by taking your fan and radiator and cover off. you will see oil around it if it's start leaking, when you replace timing belt is the best time to replace it as well.

Posted on Sep 04, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Leaking oil from the timing chain cover


The problem is the amount of items you have to remove so you can get to the timing chain cover, remove it and replace a $5 gasket.

You can try tightening all the bolts a LITTLE. Don't overdo it though because if you break the bolts, you are looking at more money to remove those.

Oct 17, 2015 | 2009 Dodge Journey

1 Answer

I NEED TIMING CHAIN DIAGRAM FOR VQ20 NISSAN SERFIRO 1999


Instructions
  1. Remove Your Timing Chain
    • 1 Check your owner's manual for the recommended mileage for replacing your timing chain. Replacement for a Nissan Altima is 60,000 miles.
    • 2 Locate the timing chain. Replace it if the automatic chain adjuster (also known as the tensioner) is damaged or worn.
    • 3 Drain the cooling system and disengage the negative battery cable. Undo the spark plug wires and set the No. 1 piston at "Top Dead Center" (TDC) of the compression stroke.
    • 4 Disconnect the engine undercover, vacuum and fuel hoses, harness and connectors, drive belts, power steering reservoir, alternator and bracket, upper radiator hose, air duct, front exhaust tube, intake manifold collector supports, collector and exhaust manifold and the distributor.
    • 5 Prop up the oil pan and take out the front engine mounting, the valve cover, camshaft sprockets, cam bearing caps, camshafts, cylinder head bolts (reverse the installation order), cam sprocket cover, upper chain tensioner, chain guides and chain, idler sprocket bolt, cylinder head, intake manifold and cylinder head gasket and the steel oil pan.
    • 6 Place a steel cutter between the steel and aluminum oil pans. Slip the cutter around the oil pan's edge. Disengage the steel oil pan, baffle plate, oil strainer and the front tube.
    • 7 Secure the car on jack stands and place a seal cutter in between the oil pan and cylinder block. Slip the cutter around the oil pan's edge.
    Install Your Timing Chain
    • 8 Reconnect the crankshaft sprocket, oil pump drive spacer, idler sprocket and lower timing chain. Position the lower timing chain on the sprockets and line up the mating marks.
    • 9 Rub on an unbroken bead of liquid gasket and put in a new front cover and oil seal. Secure the bolt at 105 to 112 foot pounds (142 to 152 Nm).
    • 10 Eliminate any old material from the pan and cylinder block mounting surfaces. Rub on a 3.5 to 4.5mm bead of liquid gasket over the oil pan and cylinder block.
    • 11 Attach the upper timing chain to the idler sprockets and secure the cylinder head bolts.
    • 12 Refill the cooling system and add clean oil in the engine.
    • 13 Hook up the negative battery cable and any other disconnected parts or items. Start the engine and look for leaks.
Tips & Warnings
  • Procedures for replacing timing chains in Nissan Altimas vary slightly depending on engine size.
  • Make sure the new timing chain matches the chain you are removing.

Jun 12, 2012 | Cars & Trucks

1 Answer

I have take all the bolts that hold the timing chain cover on place but still don't come out does anyone have a diagram on how to


Check for any bolts coming up from oil pan into bottom of timing chain cover. If they are also removed, the cover may be stuck on with silicone, and just needs (gently) pried off.

Nov 07, 2011 | 2002 Nissan Altima

1 Answer

Water pump bolt broke off


Common problem. You are in for a rough ride my friend. The only way to fix that is to remove the rest of the bolts, the front crankshaft dampener pulley and take the timing chain cover off. Usually the bolt is seized into the timing cover itself and the timing cover ends up getting destroyed in the process. Once the cover is out of the way, the bolt will most likely come out fairly easilly with a pair of Vise-Grips.

Fortunately, a replacement timing chain cover is not real expensive. The trick is to get the [BLANKETY] thing off without causing any damage to the engine block. If you are going that far, I recommend putting a new timing chain set on it while you are in there.

Recommended parts: Timing cover gasket and front seal set, timing chain and gear set, and possibly a new timing cover unless you can get it off without ANY damage.

Keep in mind that if you have to pry it off and the pry tool leaves indentations in the gasket surface, or if you "warp" the cover, the timing cover MUST be replaced unless you want to do the job over to fix oil and engine coolant leaks. (It doesn't take much to make the thing leak)

Aug 16, 2011 | 1991 Ford F150

1 Answer

I replaced the right side head on my 2001 mustang gt and i need to know how to set up the timming so it will run right


Hi, this engine user copper links on the chain align the copper links with the marks shown on the diagram below. Please let me know if you have more questions, and thanks for using FixYa.

To install:
  1. Compress the timing chain tensioner plunger in a soft jaw vise and install a retaining clip to hold the plunger in place.
  2. Remove the tensioner.
  3. If the copper links are not visible on the timing chains, mark one link on each end of the chain.
  4. Install the left and right timing chain guides and tighten the bolts to 89 inch lbs. (10 Nm).
  5. Position the lower end of the left timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  6. Position the timing chain on the left camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  7. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  8. Remove the retaining clip from the tensioner plunger.
  9. Position the lower end of the right timing chain on the crankshaft sprocket, aligning the copper link with the timing mark on the outer flange of the crankshaft sprocket.
  10. Position the timing chain on the right camshaft sprocket with the camshaft sprocket timing mark aligned with the copper link.
  11. Position the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner. Tighten the bolts to 18 ft. lbs. (25 Nm).
  12. Remove the retaining clip from the tensioner plunger.
  13. Ensure correct alignment of all timing chain links and sprocket timing marks.
  14. Install the camshaft roller followers and tighten the camshaft sprocket bolts. See the procedure under Camshaft.
  15. Install the crankshaft sensor ring on the crankshaft.
    jturcotte_2085.gif

    Fig. Timing chain link and sprocket timing mark alignment-4.6L engine

  16. Apply sealant to the front cover mating surface as shown.
    jturcotte_2086.gif

    Fig. Sealant application to the front cover mating surface-4.6L engine

  17. Install a new gasket on the front cover, then install the front cover and hand tighten the bolts.
  18. Tighten the front cover bolts in the sequence shown to 18 ft. lbs. (25 Nm).
  19. Tighten the front cover-to-oil pan bolts in the sequence shown to 15 ft. lbs. (20 Nm), plus an additional 60 degrees
    jturcotte_2087.gif

    Fig. Front cover bolt tightening sequence-4.6L engine

    jturcotte_2088.gif

    Fig. Front cover-to-oil pan bolt tightening sequence-4.6L engine

  20. Lubricate the engine front cover and oil seal lip with clean engine oil and install the seal using a seal installer.
  21. Apply sealant to the Woodruff key slot in the crankshaft pulley, then press on the crankshaft damper.
  22. Tighten the crankshaft damper as follows:
    1. Step 1: 66 ft. lbs. (90 Nm).
    2. Step 2: Loosen the bolt one full turn.
    3. Step 3: 37 ft. lbs. (50 Nm).
    4. Step 4: 90 degrees.

  23. Connect the crankshaft position sensor connector.
  24. Install the power steering pump and tighten the bolts to 18 ft. lbs. (25 Nm).
  25. Install the wiring harness retainer to the power steering stud bolt.
  26. Install the power steering pump pulley shield.
  27. Install the water pump pulley.
  28. Install the J bracket to the engine front cover stud bolt.
  29. Install both left and right camshaft position sensor connectors.
  30. Install both left and right radio interference capacitors.
  31. Connect the hoses from the coolant crossover.
  32. Install the valve covers. See the procedure under Cylinder Head.
  33. Install the right side idler pulley.
  34. Install the accessory drive belt.
  35. Install the coolant degas bottle.
  36. Connect the negative battery cable.
  37. Fill the crankcase with clean engine oil.
  38. Start the engine. Check for leaks and proper operation.

Aug 14, 2011 | Ford Mustang Cars & Trucks

1 Answer

I have a 2001 Olds Aurora with a V6 3.5 and I need the timing diagram for this. I have looked everywhere and can not find a book with it in it. Would you happen to have this??


Please let me know if you have questions, and thanks for using Fixya.


jturcotte_1505.gif

To install:

  1. Rotate the crankshaft so the No. 1 piston is at TDC and the mark on the crankshaft is at the 4 o-clock position.
  2. Rotate the balance shaft so the timing mark is at the 5 o-clock position.
    NOTE Be sure the painted links are facing the front of the engine.
  3. Install the timing chain on the sprockets.
  4. Center the mark on the left intake camshaft sprocket between the 2 painted links.
  5. Lift the chain onto the right intake camshaft sprocket. While doing this, align the marks on the balance shaft and crankshaft sprockets with the painted marks on the chain.
  6. Verify that all of the timing marks are aligned.
  7. Install the primary chain tensioner shoe. Torque the bolt to 22 ft. lbs. (30 Nm).
  8. Compress the primary chain tensioner using the following steps:
    1. Rotate the ratchet release lever counterclockwise and hold it.
    2. Press the tensioner shoe in and hold it.
    3. Release the ratchet lever and slowly release the pressure on the shoe.
    4. Insert a pin through the hole in the lever as the lever moves to the first click. The ratchet should hold the shoe in the compressed position.
      NOTE Be sure the lever on the tensioner is facing you when installed.

  9. Install or connect the following:

    Primary chain tensioner. Torque the bolts to 18 ft. lbs. (25 Nm); then remove the chain tensioner pin. 4 chain guide access plugs. Torque the plugs to 44 inch lbs. (5 Nm). Front engine lift bracket. Torque the hex head bolt to 37 ft. lbs. (50 Nm) and the internal drive bolt to 18 ft. lbs. (25 Nm). CMP sensor. Torque the bolts to 80 inch lbs. (9 Nm).
  10. Remove the camshaft holding tools.
  11. Place a small bead of RTV sealant on the 3 areas indicated in the diagram.
  12. Install or connect the following:

    Front cover with a new gasket. Torque the bolts to 124 inch lbs. (14 Nm) and the coolant drain plug to 89 inch lbs. (10 Nm). Crankshaft balancer. Torque the bolt to 37 ft. lbs. (50 Nm); then an additional 120 degree turn.
  13. Raise the engine cradle and install new bolts. Torque the bolts to 133 ft. lbs. (180 Nm).
  14. Coat the sub-frame bushings with rubber lubricant.
  15. Install or connect the following:

    Water pump with a new gasket. Torque the bolts to 124 inch lbs. (14 Nm). Belt tensioner. Torque the bolts to 37 ft. lbs. (50 Nm). Idler pulley. Torque the bolt to 37 ft. lbs. (50 Nm). Power steering pump pulley Drive belt Underhood accessory wiring junction block Washer and coolant reservoirs Battery and tray Front diagonal brace Rocker arm covers. Torque the bolts to 80 inch lbs. (9 Nm). Negative battery cable
  16. Refill the cooling system.
  17. Refill the crankcase.
  18. Start the engine and verify no leaks.
Secondary Chain
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the rocker arm cover and install camshaft holding fixture J-42038.
  4. Remove the camshaft sprocket bolts and install the timing chain holding fixture J-42042 on the cylinder head.
  5. Remove or disconnect the following:

    Sprockets and chain Secondary timing sprocket and chain
To install:

jturcotte_428.jpg

Fig. Correct sprocket alignment for the left secondary timing chain-3.5L engine


jturcotte_429.jpg

Fig. Correct sprocket alignment for the right secondary timing chain-3.5L engine

  1. Install or connect the following:

    Secondary timing chain on the sprockets, with the drive pins at the 12 o-clock positions Sprockets and chain assembly onto the camshafts, with the chain properly aligned on the tensioner
  2. Remove the timing chain holding fixture
  3. Install the sprocket bolts. Torque the bolts to 18 ft. lbs. (25 Nm); then an additional 45 degree turn.
  4. Remove the camshaft holding fixture.
  5. Install or connect the following:

    Rocker arm cover Negative battery cable

Apr 09, 2011 | 2001 Oldsmobile Aurora

1 Answer

Aligning the valve timing mareks except twincam engine


Timing Chain, Sprockets, Front Cover and Seal REMOVAL AND INSTALLATION Crankshaft Damper and Front Oil Seal
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt
    • Cooling fans
    • Crankshaft pulley and damper, using a holding fixture as shown
    • Front crankshaft seal Fig. 1: Crankshaft pulley removal tool - V8 9301jg12.gif
    To install:
  3. Install oil seal replacer tool JD-235 to the oil seal. Use the nut and bolt provided with the tool to fully seat the seal to the timing cover.
  4. For dampers which DO NOT utilize a spit locking ring:
    1. Apply a thin, even coating of Loctite® 648 to the damper bore. Do not apply it to the end faces or to the crankshaft.
    2. Install the crankshaft damper onto the crankshaft. Wipe off any Loctite that has squeezed out from the front of the damper.
    3. Install the locking tool to the damper. Tighten the bolt to 59 ft. lbs. (80 Nm), plus an 80 degree turn.
  5. For dampers which utilize a spit locking ring:
    1. Install a new O-ring seal to the damper.
    2. Install the crankshaft damper.
    3. Apply petroleum jelly to the damper bore and O-ring seal.
    4. Install the damper onto the crankshaft.
    5. Install the split locking ring onto the crankshaft, inside the center bore of the damper.
    6. Install the locking tool to the damper.
    7. Tighten the damper bolt to 266-285 ft. lbs. (364-386 Nm).
    8. Remove the locking tool from the damper.
  6. Install or connect the following:
    • Cooling fans
    • Accessory drive belt
    • Negative battery cable
  7. Start the engine and check for leaks.
Timing Cover
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose
    • Accessory drive belt
    • Water pump pulley
    • Accessory drive belt tensioner
    • Idler pulley
    • Crankshaft damper
    • Engine appearance covers
    • Mass Air Flow (MAF) meter
    • Air intake assembly
    • Ignition coils
    • Canister purge valve
    • Valve covers
    • Variable Valve Timing (VVT) solenoids
    • Engine harness retaining clips
    • Timing cover
    To install: Fig. 2: Sealant application points - V8 9301jg23.gif
    Fig. 3: Timing cover torque sequence-V8 9307jg01.gif

  4. Apply sealant to the 8 joints on the engine face as shown.
  5. Install or connect the following:
    • Timing cover with new seals. Tighten the bolts in sequence to 96-120 inch lbs. (11-13 Nm).
    • Engine harness retaining clips
    • VVT solenoids
    • Valve covers
    • Canister purge valve
    • Ignition coils
    • Air intake assembly
    • MAF meter
    • Engine appearance covers
    • Crankshaft damper
    • Idler pulley
    • Accessory drive belt tensioner
    • Water pump pulley
    • Accessory drive belt
    • Upper radiator hose
    • Negative battery cable
  6. Fill the cooling system.
  7. Start the engine and check for leaks.
Timing Chain 6 CYLINDER
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Accessory drive belt
    • Valve cover
    • Timing chain cover
    • Variable Valve Timing (VVT) sensor
    • Crankshaft Position (CKP) sensor
  3. Rotate the crankshaft until the triangular arrow indent on the driveplate is visible through the access hole.
  4. Install the Crankshaft Setting Peg JD 216 into the CKP sensor location.
  5. Install the Camshaft Locking tool JD 215 on the camshafts.
  6. Remove or disconnect the following:
    • Camshaft sprocket mounting bolt by loosening it
    • VVT mounting bolt by loosening it
    • Camshaft Locking tool JD 215
    • Primary timing chain tensioner and backing plate
    • Primary timing chain guide
    • VVT unit and exhaust camshaft sprocket
    • Secondary timing chain tensioner and guide
    NOTE: Keep all valvetrain components in order for assembly. To install:
  7. Prepare the timing chain tensioners for installation by using a paperclip or other wire to unseat the check valves and compressing the pistons into their bores.
  8. Install or connect the following:
    • Secondary timing chain guide. Tighten the bolt to 89-124 inch lbs. (10-14 Nm).
    • Secondary timing chain tensioner. Tighten the bolt to 89-124 inch lbs. (10-14 Nm).
    • VVT, secondary timing chain and exhaust cam sprocket
    • Primary timing chain
    • Primary timing chain guide. Tighten the bolt to 10-12 ft. lbs. (13-16 Nm).
    • Primary timing chain tensioner and backing plate. Tighten the bolts to 89-124 inch lbs. (10-14 Nm).
    • Primary timing chain slack, eliminate it by placing a wedge between the primary timing chain tensioner and the guide shoe
    • Secondary timing chain by applying counterclockwise force to the exhaust camshaft sprocket. Fig. 4: Apply force in a counterclockwise direction when tightening the sprocket mounting bolts - 6 cylinder 9301jg03.gif

    • Exhaust and intake VVT sprocket bolts. Tighten them to 85-92 ft. lbs. (115-125 Nm).
  9. Remove the tools and wedges.
  10. Install or connect the following:
    • CKP sensor
    • VVT sensor
    • Coolant outlet pipe
    • ECT sensor connector
    • Radiator and heater hoses
    • Timing chain cover
    • Valve cover
    • Accessory drive belt
    • Negative battery cable
  11. Fill the cooling system.
  12. Start the engine and check for leaks.
prev.gif next.gif

Jan 28, 2011 | 1999 Jaguar XK8

1 Answer

What is the right way to time a 4cyl Chevy S-10 timing chain


1998-2003 To Remove:
  1. Remove or disconnect the following:
    • Crankshaft pulley and hub
    • Drive belt tensioner gm_truck_s10_tcbolts.gif

    • Timing chain cover bolts gm_truck_s10_tc.gif

    • Timing chain cover and gasket
  2. Install a bolt in the end of the crankshaft CAUTION
    Do not install the crankshaft balancer bolt or a bolt longer than 1 inch or damage to the crankshaft threaded hole will result.
  3. Rotate crankshaft until the number 1 piston is at Top Dead Center of compression stroke.
  4. Make sure that the alignment marks are aligned with the tabs on the timing chain tensioner. gm-03-22-611.gif

  5. Measure distance between hole in bracket and unworn surface of timing chain tensioner shoe. NOTE: If distance between the hole and unworn surface of timing chain tensioner is greater than 0.314 in (8 mm), replace tensioner, timing chain and sprockets.
  6. Remove timing chain tensioner bolts.
  7. Remove the timing chain, timing chain tensioner and camshaft sprocket at the same time.
  8. Remove the crankshaft sprocket using special tool J 22888-20A or equivalent.
  9. Remove crankshaft sprocket alignment key.
gm-03-22-612.gif

NOTE: If any camshaft components are being replaced to correct a noise problem, all camshaft drive components must be replaced.
To Install:
  1. Install the crankshaft sprocket alignment key.
  2. Install the crankshaft sprocket using special tool J 5590 or equivalent. gm-03-22-613.gif

  3. Compress the timing chain tensioner spring and insert a pin into the tensioner hole to retain the tensioner shoe.
  4. Install timing chain and timing chain tensioner (do not tighten tension bolts).
  5. Align the crankshaft and camshaft timing marks with the tab on the timing chain tensioner.
  6. Tighten the timing chain tensioner bolts.
    • Torque to: 18 ft lbs (24 Nm)
  7. Tighten the camshaft sprocket bolt.
    • Torque to: 96 ft lbs (130 Nm)
  8. Remove pin from timing chain tensioner hole.
  9. Remove bolt from end of crankshaft. CAUTION
    Inspect the timing chain cover for warping or damage. Replace if needed.
  10. Clean all timing chain cover mating surfaces.
  11. Install or connect the following:
    • Timing chain cover to the engine block
      1. Ensure that the gasket is installed properly in the groove in the timing chain cover
    • Timing chain cover and make sure it fully seated on the alignment dowel pins
    • Timing chain cover bolts
      1. Torque to: 97 inch lbs (11 Nm)
    • Drive belt tensioner
    • Crankshaft damper hub and the crankshaft pulley

Aug 17, 2010 | 2000 Chevrolet S-10

2 Answers

Hi guys I need some help with the drive shaft for a 97 cavalier z22 2.2engine. I decided I was going to change the timing chain this weekend after hearing a noise for some time and came to the...


Timing Chain and Gears REMOVAL & INSTALLATION 2.2L Engine Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned 91113p63.jpg
Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2) 91113p58.jpg
Fig. 3: Unfasten the camshaft sprocket bolt 91113p59.jpg
Fig. 4: Remove the camshaft sprocket and the timing chain at the same time . . . 91113p60.jpg
Fig. 5: . . . then remove the tensioner assembly 91113p61.jpg
Fig. 6: Compress the tensioner spring and insert a cotter pin or nail in the hole provided to hold the tensioner in position 91113p62.jpg
  1. Disconnect the negative battery cable.
  2. Remove the front cover as previously detailed.
  3. Place the No. 1 piston at TDC of the compression stroke so that the marks on the camshaft and crankshaft sprockets are in alignment (see illustration).
  4. Loosen the timing chain tensioner nut as far as possible without actually removing it.
  5. Remove the camshaft sprocket bolts and remove the sprocket and chain together. If the sprocket does not slide from the camshaft easily, a light blow with a soft mallet at the lower edge of the sprocket will dislodge it.
  6. Using a suitable gear puller, remove the crankshaft sprocket. To install:
  7. Press the crankshaft sprocket back onto the crankshaft.
  8. Install the timing chain over the camshaft sprocket and then around the crankshaft sprocket. Make sure that the marks on the two sprockets are in alignment (see illustration). Lubricate the thrust surface with Molykote® or its equivalent.
  9. Align the dowel in the camshaft with the dowel hole in the sprocket and then install the sprocket onto the camshaft. Use the mounting bolts to draw the sprocket onto the camshaft and then tighten to 66–68 ft. lbs. (91–95 Nm).
  10. Lubricate the timing chain with clean engine oil. Tighten the chain tensioner.
  11. Installation of the remaining components is in the reverse order of removal. Fig. 7: Exploded view of the timing chain and sprockets — 2.2L OHV engine 87953107.gif

Aug 03, 2010 | 1997 Chevrolet Cavalier

1 Answer

1992 Volvo 940Gle Oil leak


sounds like a cam seal find repair manual ( haynes book ) at parts store. on a 92 the book is definitely out although it might need to be ordered

hope2help shack

Apr 17, 2009 | 1992 Volvo 940

Not finding what you are looking for?
1991 Toyota Pickup Logo

125 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...