Question about 1998 Honda Accord

1 Answer

-= Blowers & vents =-

Hi there - thanks in advance. I cannot figure out the front windshield vents are not activating when I select them. The light on the control panel on the dash is yellow, which means that it is is failing ( assumed ). The air seems to be coming out from another vent internal of the dash. Please advise.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

This sounds like u have a blending door problem these are like flaps that control the air flow in ur system. these tend to go bad u need to figure out if they are controlled by vacuum or manually

Posted on Oct 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the problem with my mode selection knob?


HAVC Blend Door problem under the dash

Oct 03, 2014 | 2003 Kia Sorento

1 Answer

Windshield washer fluid light


Pull the connector on the sensor and short the 2 leads together with a paperclip. If the light comes on you need to replace the sensor.

Jun 18, 2013 | Mercedes-Benz Cars & Trucks

1 Answer

1998 Tercel Cold heat to the windshield. Lukewarm out front vent.


Hey,

I just replaced my thermostat in my car due to the same problem. Except mine was a 92. I figured I'd start with the thermostat and antifreeze. Then the heating core. Now I have heat.

But yet I still have no heat on the windshield.

Oct 23, 2009 | Toyota Tercel Cars & Trucks

1 Answer

Cabin air filter


it;s under the cowl vent panel.

Cowl Top Vent Panel Removal
  1. Remove the windshield wiper pivot arm (17526) . Refer to Section 01-16 for the removal procedure.
  1. Remove the front door weatherstrip (20530) to access the windshield outside side moulding screws.
b981661.gif
  1. Remove the five windshield outside side moulding screws and the windshield outside side moulding (03136) .





  1. Pull the windshield outside moulding (03144) from the windshield glass (03100) .
  1. Remove the three Phillips-head screws from the cowl top vent panel (022A68) .


9bc8ed6.gif

  1. Remove the three plastic screws by turning them 90 degrees to unlock.





  1. Remove the six pushpins from the front edge of the cowl top vent panel .
  1. Lift up on the cowl top vent panel and disconnect the windshield washer hose (17A605) at the Y-connector.





  1. Remove the cowl top vent panel .

Mar 15, 2009 | 1998 Mercury Villager

1 Answer

Air conditioner makes noise which increases as you rev the engine and slows as you take foot off the gas.also, the front vents (by the windshield) also noisy when you switch to them,opposed to having the...


YOU SEEM TO HAVE A LOOSE OR BAD AC COMPRESSOR DRIVE BELT. WHEN YOU SWITCH THE TO THE VENTS CLOSE TO THE WINDSHIELD IT TURN THE AC COMPRESSOR CLUTCH ON, IT ACTIVATES THE DEFROST. TRY POURING SOME WATER ON THE AC BELT AND SEE IF NOISE GOES AWAY. THE BELT MAY NEED ADJUSTMENT OR MAY NEED TO BE REPLACED. GOOD LUCK

Dec 10, 2008 | Hyundai Santa Fe Cars & Trucks

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

199 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...