Question about 1995 Dodge Intrepid

1 Answer

Won't Start I have a 1995 Intrepid 3.3L V6 that i recently purchased for $300. it ran fine for a day or two, then i went to leave for work the next morning and got about 5 minutes down the road, it died. started again, died again, finally made it back home, and now it won't start at all. I have changed the plugs, plug wires, ignition coil, cam sensor, crank sensor, and it's still not firing to the plugs. it is flashing codes 1277, and 5455. Can anyone tell me what those codes mean? Any help is greatly appreciated

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

My daughters car did the exact same thing. Lights and all. I replaced the pump twice and both relays (auto shut down and fuel pump relay). Very frustrating indeed.

The 1994 recall (see below) is right on! Right behind the engine block intake (the long aluminum block on top) is a tie rod that connects from the rack and pinion to the wheel. On top of the tie rod is a bundle of wires that are wrapped in cloth style tape, just resting on the rod. As the vehicle is driven, the steering rod will rub the wires (as the wheels are turned) thus causing a possible short. My daughters was. I used liquid tape, wrapped in tape and used zip ties to lift off the rod. I have driven it alot and have not had an incident yet!

FEB 08, 1994 | Recall ID# 12389 Hide Details
Recall Reason ELECTRICAL SYSTEM:WIRING
Recall Date FEB 08, 1994
Model Affected INTREPID
Potential Units Affected 110000

Recall Summary
THE RIGHT STEERING TIE ROD CAN RUB THROUGH THE AUTOMATIC TRANSMISSION WIRING HARNESS CAUSING A SHORT CIRCUIT WHICH RESULTS IN ELECTRICAL SYSTEM MALFUNCTIONS INCLUDING ENGINE STALLING AND AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM.

Consequence
ELECTRICAL SYSTEM MALFUNCTION CAUSING STALLING WHILE IN MOTION OR AN INOPERATIVE PARK/STARTER INTERLOCK SYSTEM, WHICH ALLOWS ENGINE START WHILE THE TRANSMISSION IS NOT IN THE PARK POSITION, MAY RESULT IN AN ACCIDENT.

Remedy (see above)
INSTALL A REVISED WIRING HARNESS BRACKET AND A PLASTIC CONVOLUTED SLEEVE TO PROTECT THE TRANSMISSION WIRING HARNESS.

Notes
CHRYSLER CORPORATION

Posted on Aug 14, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced distributor in 2000 nissan quest ,now van wont start


check if there is spark in your plugs, if none, just replace ignition coil.

Jun 10, 2013 | 2000 Nissan Quest

1 Answer

1995 miata cranks but won't turn over


Possibly the fuel pump or crankshaft sensor

Oct 20, 2012 | 1995 Mazda MX-5

1 Answer

I have a 98 Intrepid with a 2.7 engine. It was driving fine on Thursday night. Went to leave for work Friday morning and it wouldn't start. So far, we have tried a new battery, had the started tested,


The 2.7 had alot of problems with the cam sensor. I would start there. Its located on the front top of the timing cover. Unplug it and see if it "Pops" attempts to start.

Nov 17, 2011 | 1998 Dodge Intrepid

1 Answer

O2 lincoln ls check engine light & fuel gauge went to empty the next day it wouldny start replaced fuel pump & fuel gauge ran fine drove about 40 miles the next day started it up check engine light...


You have two pumps,I guess you know that ,if you already did one. Did you check fuel pressure at the rail and check out the electronic pressure regulator? What codes are coming up and do they stay set?

Feb 05, 2010 | 2002 Lincoln LS

1 Answer

1994 Lexus will not start


i'd change the filter which is under the car on the drivers side just trace the fuel lines from the rear of the car toward the front its a large cylinder 9if that don't work then shoot it)

Apr 11, 2009 | 1995 Lexus ES 300

1 Answer

Engine Will Not Start - E-Brake Problem?


Before getting into a bunch of electronic nightmares, remove and clean both battery terminals & cable ends. (use a small knife & or rough sandpaper. Additionally, make sure the other ends of cables are clean and tight at their connections. nothing in your electrical system will function properly without a good connection at the battery.

Feb 05, 2009 | 2000 Dodge Intrepid

Not finding what you are looking for?
1995 Dodge Intrepid Logo

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...