- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
There are two fuses to the instrument panel(IP). one is for illumination. One is for the digital control. The one for digital controls all of them. IE.. speedo, tach, oil,engine temp and so on. If any of them work, the fuse is good. There are 1 or 2 wires to the IP that transfers data. Depending on year.
That is the Renault equivalent of a "Service Vehicle Soon" light. (Not to be confused with "Service ENGINE soon") This means that there is a problem with the body or suspension control systems in the vehicle. The computer system must be scanned to find out the nature of the problem and begin diagnostics and/or estimate for repair.
1. Press and hold button [A] in the picture below.
2. Switch ignition ON. 3. The letters "OIL" will appear in the trip recorder display. 4. Release button [A]. 5. Press and release button [A]. 6. The letters "INSP" will appear in the trip recorder display. 7. Pull out button [B] for approximately 2 seconds to reset the display.
Turn the ignition
key to the OFF position with the odometer reading shown. Turn the
ignition key to the ON position while holding down the trip meter
reset button. Hold down the button until the light goes off. Before
the light goes off, it illuminates for 3 seconds, flashes for 2
seconds, and illuminates for 1 second. If the system fails to reset,
the light will remain flashing.
Ive never heard of a timing belt light, but there is a maintenance light that can be reset. Here the procedure:
To reset the maintenance reminder light:
Turn the ignition switch to the "ON" position.
Set the odometer/trip display to the odometer (ODO) mode.
Turn the ignition switch off.
Depress and hold the trip meter reset button while turning the ignition switch to the on position.
The maintenance reminder light will, illuminate for 3 seconds, blink for 2 seconds, illuminate solid for 1 second and then turn off.
Release the trip meter reset button.
Turn the ignition switch to the off position.
Turn the ignition switch to the on position.
Confirm that the maintenance light goes out.
Let me know if this helped you out!
h) Engine Oil Replacement Reminder
Light (for vehicles sold in U.S.A.)
This light reminds you when to replace
the engine oil.
This light will come on when the ignition
key is turned to “ON” and will go off after
about a few seconds.
When you drive for about 8000 km (5000
miles) after the engine oil replacement,
this light illuminates for about 3 seconds
and then flashes for about 12 seconds
with the ignition key turned to “ON” position.
If you continue driving without the
engine oil replacement, and if the driving
range exceeds 12000 km (7500 miles), the
light will come on after the ignition key is
turned to “ON” position. The light will remain
If the light is flashing, we recommend that
you replace the engine oil at an early
opportunity depending on the driving and
road condition. If the light comes on, replace
it as soon as possible.
You need to reset the light after the engine
oil replacement. Reset the light by
following the procedure below:
1. Turn the ignition key to the “OFF” position
with the odometer reading shown.
(For details, see “Odometer and two
trip meters” on page 136 in this Section.)
2. Turn the ignition key to the “ON” position
while holding down the trip meter
Hold down the button until the light goes
off. Before the light goes off, it illuminates
for 3 seconds, flashes for 2 seconds and
illuminates for 1 second.
If the system fails to reset, the light will
I copied this from page 143 of the owners manual for the 2004 4Runner