Question about 1999 Isuzu Rodeo

1 Answer

1999 rodeo 6 cyl

Engine will not run unless gas peddle is pushed down when let off peddle engine stops

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 178 Answers

Hello from what you explained i take it theres no check engine lights on what it sounds like is a basic increase on your idle screw get somone to help push pedal down underhood look to see where gas cable pulls back when gas pedals appled have them release slowly now watch where it stops against a set screw that is your adjustment rpm range should be somewhere between 750-900 rpm depending on vehicle if this doesnt solve most likely tps sensor{ throttle position sensor} goodluck

Posted on Sep 13, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replaced engine with the same engine from a buick lucerne the engine starts but when gas peddle is pressed the engine will not accelerate the power down light appears


its common for the computer to not sync with new--u will need a data stream run from a pro not a dealer--may need reprogramin-unless its something with wiring or some othr ajust

Jun 30, 2013 | 2006 Pontiac Grand Prix

1 Answer

1994 corvette running too rich black smoke and coughing low rpm


the brake servo needs refitting and ensuring correct torque

Jun 11, 2013 | 1994 Chevrolet Corvette

1 Answer

My 1988 dodge Dakota 3.9 3 speed automatic 2 w Dr.idles rough and sometimes dies at a stop light and won't restart unless I put the gassed peddle to the floor.when it does finally start I have to keep...


Replace your hose going from intake to brake booster ( vacuum leak) check all other hoses also. Clean the throttle body. And a tune up probably wont hurt either.

Jun 09, 2017 | Cars & Trucks

2 Answers

Drive vehicle down the road for 20 minutes and come to a stoplight engine stops when you take foot off gas peddle and go to apply brake. To keep vehicle from dying you have to hold the gas peddle down


Have you changed the timing belt? or timing belt guides? How many miles? This does not necessarily have to do with fuel.... Could have to do with air intake or timing as well....

Jun 12, 2012 | 1996 Dodge Ram

1 Answer

When push brakes you have to push really hard to make them go in then the truck barely stops. Replaced the MC and bled the brakes now every time push brakes truck acts like its going to die. Brake light...


Sounds like you will have to bleed your brakes again, but thats not the problem og hard brake peddle, need to check your power brake booster, sit right in back of master cylinder, check make sure it has vacum going to it, also to test it with engine off, press on brake peddle three time, then state engine with foot on peddle, peddle should go down a few inches, also with engine of peddle should feel soft for three pumps, if you have none of this , power brake booster is bad.

Jul 04, 2010 | 1995 Toyota 4Runner

1 Answer

Van won't stay running unless i give it gas. It clacks very loud and has little power. Brakes are hard to press down and stop. Runs rough and white smoke comes out the exhaust.


Head gasket has failed and your engine from what you have described will need to be replaced, the clack and no power indicates that your crank shaft bearing has slipped and your you have low oil pressure now throughout your engine.
Oil pressure is created by the crankshaft bearing and for you to have to push hard on your brake peddle to stop also indicates that your engine is low on vacuum caused by a blown head gasket.
Thank you for using fixya and sorry for the bad news that a new engine is called for to fix this issues.

Jun 15, 2010 | 1999 Dodge Grand Caravan

2 Answers

I need to learn how to reset the change oil light since the mechanics forget to do this when I get my oil changed.


On a Envoy you turn the key to run but don't start it. Then push and release the gas pedal 3 times within 5 seconds. The change engine oil light should blink for 5 seconds meaning you have reset the system. If it doesn't blink for you do the procedure again.

Oct 18, 2009 | 2003 GMC Envoy Xl

1 Answer

Gas padle is hard to push


you might check the cable that runs to the air box that runs from the gas peddle to the air box. see if it is bent or something obstructing the movement of the arm on the airbox the thing that use to be a carburetor or older vehicles

Jan 19, 2009 | 2001 Chevrolet Blazer

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14406 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...