Question about 2000 Dodge Intrepid

1 Answer

Need new fan belt outer

How to remove the outer fan belt on a 2000 Intrepid

Posted by on

  • Anonymous Sep 20, 2008

    how to replace a/c belt 200- dodge intriped 3.2

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 6,674 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace water pump 99 2.7


Hope this helps you....

Instructions
  1. Prepare the Dodge Intrepid
    • 1 Lay out a drop cloth underneath the Dodge Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
    • 2 Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
    • 3 Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
    • 4 Use a grease pencil to mark on the timing belt its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
    Remove the Damaged Pump
    • 5 Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
    • 6 Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
    • 7 Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
    • 8 Clean off the mounting area with a shop rag.
    Install the New Pump
    • 9 Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
    • 10 Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
    • 11 Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
    • 12 Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
    • 13 Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.

Read more: How to Install a Water Pump in a Dodge Intrepid ' eHow.com http://www.ehow.com/how_4508707_install-water-pump-dodge-intrepid.html#ixzz29Q1ZC1uZ

Oct 15, 2012 | 1999 Dodge Intrepid

1 Answer

Removal of alternator on 2000 dodge intrepid 3.2


  • Very easy one hour job for most DIY's
    .Disconnect the negative (black) cable from the battery, then remove the positive (red). Unbolt and remove the upper support rail for the radiator.

  • Loosen the lower mounting bolt and pivot bolt on the alternator, but do not remove it. This relieves tension from the belt. Remove the belt.
  • Disconnect the electrical connectors. The battery line is connected with a nut.
  • Unbolt and remove the alternator. Install the replacement using the reverse procedure. Torque the battery cable nut to 85 in-lbs. (7 ft-lbs.) and the mounting and pivot bolts to 40 ft-lbs.
  • Aug 28, 2012 | 2000 Dodge Intrepid

    1 Answer

    How do I replace timing belt on 2000 Dodge Intrepid R/T v6-3.5 L high output engine. Is there a book or somthing that will guide with with everything I need to know to get it right


    Thank you for the inquiry. change-1997-dodge-intrepid-3_5l-800x800.jpg




    Disconnect the negative (black) cable from the battery.

    Remove all accessories that are in the way of the timing belt cover. The Intrepid's 3.5 liter engine and small engine bay make for very cramped working conditions; it is thus necessary to remove all engine accessories so that you can properly work on the timing belt. Begin by loosening the tension bolt on the alternator with a belt tensioner, then use a socket wrench to remove the bolts on the water pump, air condition compressor and power steering pump.

    Remove the four bolts on the top timing belt cover, using a socket wrench, then remove the cover.

    Use a jack to lift the front end of the Intrepid and place the front end securely on two jack stands. Get underneath the engine.

    Remove the three bolts on the bottom timing belt cover, using a socket wrench, then remove the cover.

    Use the belt tensioner to put some slack into the timing belt, then remove the belt from the pulleys with your hands.

    Line up the pulleys, so that the engine is at the top dead center and the two marks on the camshaft are lined up with the marks on the cams.

    Place the new timing belt over the pulleys, making sure not to move any of the pulleys in either direction.

    Use the tensioner to tighten the belt.

    Reattach the top and bottom timing belt covers and secure them in place, using the bolts you had removed earlier.

    Reattach all of the accessories you have removed (in any order), using a socket wrench. When done, place the belts over the pulleys and return tension to them by using the belt tensioner to tighten the tension bolt on the alternator.

    Attach the negative (black) battery cable to the battery.

    Jun 04, 2011 | Dodge Intrepid Cars & Trucks

    2 Answers

    Timing belt diagram for toyota corolla 2000 ae112


    easiest way to change a timing belt is to
    first slightly slacken off the belt tensioner
    carefully cut the old belt in half along its entire length while it is still on the engine.
    remove the outer half only.
    place the new belt on the pulleys up against the inner half of the old belt.
    cut and remove the inner half of the old belt.
    push the new belt fully into place.
    re tension the belt as specified.

    Feb 20, 2011 | 2000 Toyota Corolla

    1 Answer

    HOW TO CHANGE WATERPUMP 1999 INTREPID 2.7


      Prepare the Dodge Intrepid
    1. Step 1 Lay out a drop cloth underneath the Dodge2_bing.gif Intrepid to protect the floor from coolant spills. Designate an area to lay out each part alongside its bolts and connecting hoses and wires. Use a drop cloth here as well, some of the parts will have traces of grease and coolant.
    2. Step 2 Disconnect the negative battery cable, using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
    3. Step 3 Use a jack to elevate the Dodge Intrepid and jack stands to shore up the jack. Release the pressure in the radiator by removing the cap. Take out the drain plug located underneath the radiator. Catch the coolant in a resealable container
    4. Step 4 Use a grease pencil to mark on the timing belt2_bing.gif its position in each pulley before removal. This will save time when reinstalling. If needed, replace the timing belt and skip marking the old one.
      Remove the Damaged Pump
    5. Step 1 Locate the water pump on the Dodge Intrepid. It's mounted on the front of the engine block and connected to the radiator and various other parts through a series of hoses. It's rotated by the timing belt. Study these parts, as you'll have to remove them.
    6. Step 2 Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In the most common Dodge Intrepid engine--the 2.7L--you'll find, in order: the upper radiator crossmember, fan module, accessory drive belts, crankshaft damper, timing cover, timing chain and guide wires.
    7. Step 3 Unbolt the water pump from the engine block, using an adjustable wrench. You may have to use a chisel to gently break the seal between the mount and the pump. Discard both the pump and the bolts.
    8. Step 4 Clean off the mounting area with a shop rag.
      Install the New Pump
    9. Step 1 Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.
    10. Step 2 Arrange the new water pump on the mount. You won't need sealant for the o-ring on a Dodge Intrepid. Hold the water pump and o-ring in place as you secure it with the new bolts. Tighten them with a torque wrench to 105 inch pounds torque in any order.
    11. Step 3 Install the timing belt and wires, using the grease pencil marks to guide you in installation. Install the rest of the parts in the order removed. The camshaft must be reconnected with a torque wrench at 125 foot pounds torque.
    12. Step 4 Replace the radiator's drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Release the jack and jack stands.
    13. Step 5 Attach the negative battery cable to the post and tighten the screw on the clamp. Crank the Dodge Intrepid's engine and check for leaks. Then, close the hood.

    Apr 04, 2010 | 1999 Dodge Intrepid

    1 Answer

    Really need some help changeing alt on 2000 intrepid


    1. Disconnect negative battery cable.
    2. Raise and support vehicle.
    3. Remove lower plastic splash shield.
    4. Remove transmission cooler and reposition cooler out of the way.
    5. Remove lower radiator cross member support and position a jack stand under radiator for support.
    6. Loosen adjusting T-bolt, but do not remove.
    7. Loosen pivot bolt, but do not remove.
    8. Remove the generator drive belt.
    9. Disconnect the generator field circuit plug.
    10. Remove the B+ terminal nut and wire.
    11. Remove pivot bolt, being careful not to lose spacer.
    12. Remove generator.
    INSTALLATION
    1. Install generator.
    2. Install pivot bolt, leave loose.
    3. Connect the generator field circuit plug.
    4. Install the B+ terminal nut and wire.
    5. Install the generator drive belt.
    6. Adjusting T-bolt and tighten belt.
    7. Remove jack stand from under radiator and install lower radiator cross member support.
    8. Reposition transmission cooler and tighten fasteners.
    9. Install lower plastic splash shield.
    10. Lower vehicle.
    11. Connect negative battery cable.

    Jan 13, 2010 | 2000 Dodge Intrepid

    1 Answer

    Where is the dodge 2002 intrepid knock sensor


    remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley

    Dec 29, 2009 | 2002 Dodge Intrepid

    1 Answer

    2000 intrepid with 2.7 -- overheads when going up


    may have a restrictive radiator, leaking head gaskets can also cause overheating under loads. have your radiator flow checked and your engine block tested for leaking head gaskets

    May 11, 2009 | 2000 Dodge Intrepid

    2 Answers

    How to put belts on a 2000 Dodge Intrepid, 2 front belts have worn out.


    Belt is pretty simple to replace here is a diagram for you car's belt. contact me if you need more help. If I fixed ya LEAVE ME A FIX-YA comment. http://www.2carpros.com/car_repair_information/tec_info/2000/dodge/intrepid/2000_dodge_intrepid_drive_belt_routing_diagram.htm

    Dec 27, 2008 | 1999 Dodge Intrepid

    2 Answers

    Waterpump removal


    its easy you pull out the radiator and fans take the belts off and then its just unbolting it and rebolting it. I just did it a couple hours ago. you should replace your rad hoses when you do this and also your belts.

    Aug 09, 2008 | 1995 Dodge Intrepid

    Not finding what you are looking for?
    2000 Dodge Intrepid Logo

    Related Topics:

    26 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Dodge Experts

    yadayada
    yadayada

    Level 3 Expert

    60960 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Dodge Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...