Question about 1999 Isuzu Rodeo

2 Answers

Car stalls when clutch is pushed in - 1999 Isuzu Rodeo

Posted by on

  • jynxxgpgt Mar 18, 2009

    drives fine as soon as i clutch and rpms drop it does not even try to run just shuts off bump key and it will start does idle but rough and rises and falls when it wants



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

1997 3.2 isuzu stalls and hard restart

Posted on Dec 26, 2008



Posted on Nov 10, 2008


1 Suggested Answer

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Car stalls when I use my clutch

this will be down to the thrust bearings on the crank shaft pushing the crank shaft against its webb's when the clutch is fully depressed would recomend new main bearings and a crank shaft grind

Dec 31, 2013 | 1990 Isuzu Amigo

1 Answer

Car stalls out when you push in the clutch

When you push in the clutch you are pushing the crank shaft forward in the main bearings but the action of the throw out bearing for the clutch pushing the fingers of the clutch pressure forward. For the engine to stall under this condition I would be checking the throw out bearing for seizure and acting as a brake on the pressure plate. Some clutch systems are part of the engine start system where you have to depress the clutch to start the engine (safety device) This may be faulty and shutting the engine down.

Oct 04, 2013 | 1992 Toyota Paseo

2 Answers

My car stalls when brake and stop

your idle valve may need cleaning. do you get ruff idling on startup ???

Jul 20, 2013 | Vauxhall Cars & Trucks

1 Answer

Transaxle clutch wont release when hot stalls engine

Replace the Torque Converter Solenoid in
the transaxle

What you have is like coming to a stop with
a manual shift & not pushing in the clutch & it stalls
the motor

The converter clutch is staying locked & your
trans is connected to the motor

Feb 14, 2013 | 1995 Buick Century

1 Answer

On a 96accord wen you press the cluch it stall

Check with the engine off by pulling and pushing back the crankshaft pulley. By doing so and the pulley comes forward and pushing backwards,there is your fault. It has the crankshaft thrusts worn and if this is a recent problem,my advice is to remove the oil pan and renew thrusts and bearings and I strongly believe the car will ran perfect. It has this problem by pressing the clutch you force the crankshaft to move forward and makes rods move to an unexpected position and stalls.

Aug 17, 2012 | 1998 Honda Accord

1 Answer

When i push clutch in it makes a grinding noise.Hard to shift into first.When i come to a stop it acts like it wants to stall

Sounds like the clutch release plate or release bearing are damage or disintegrated. Because one or both of these parts are damaged the clutch does not properly disengage which will result in crunching gear changes at slow speed and also clutch dragging at lights (wanting to stall) etc.

You'll need to split the transmission from the engine block to investigate.

Apr 09, 2012 | 1997 Ford Ranger SuperCab

1 Answer

99 chevy blazer idles rough when comming to a stop in drive

Could be your Torque convertor Lockup clutch Seloniod. Maybe the clutch doesn lock as it should and the transmission makes the engine bumps . if you ever drove a stick then you would know what i;m talking about as when you go to a stop light you have to push the clutch if not the car will be jumping untill it stalls. because in the automatic there is the Torque convertor lockup cluch that locks the transmission from making it stalls and in the Manual there is the clutch pedal. Hope this is clear and helps. Good luck

Dec 11, 2010 | 1999 Chevrolet Blazer

1 Answer

Car stalls when braking

It appears that the clutch is not releasing properly when you push the pedal down. How much free-play does the pedal have when you start to push it down? It should be about 3/4 inch or so. With the engine off and in first gear, have someone push the clutch pedal down all the way while you try to rock the car back and forth. If it is trying to turn the engine while you do this, the clutch is either not capable of being released or the clutch hydraulic system is delivering insufficient oil to the slave cylinder at the clutch release arm/shaft. If this worked correctly before the new parts were put in, the person(s) that did the work should be responsible for getting it to work again. Make sure that you don't have several floor mats that are under the pedal thus preventing full clutch release. Hope this helps!

Apr 04, 2010 | 1989 Volkswagen agon

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

221 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

85206 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

459 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides