Question about Mercury Sable

1 Answer

Where can I find a timing chain cover for a 94 mercury sable

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 96 Answers

Probably the only place you will find one is in a salvage yard.

Let me know what size engine and I will keep my eyes open for one.

Posted on Aug 10, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can someone pleaze explain to me in detail where my timing belt is and how to replace it? I have a 1999 mercury sable 3.0 v6 dohc.


There are two different 3.0 engines avaliable in this car. Both were timing CHAIN engines and do not have a scheduled replacement . No worries!

Jan 30, 2011 | 1999 Mercury Sable

2 Answers

I need to change my turning signal fuse in a 2000 mercury sable but cannot locate the fuse relay. Can anyone tell me where it is located. I have no turning signals right now!


For 2000 Mercury Sable 3.0L EFI DOHC 6cyl the Flasher is located on front seating area, driver side, under dash, mounted in junction block.

zjlimited_253.jpg

Passenger compartment fuse panel
The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover. I suggtes check the next positions...

zjlimited_254.jpg


zjlimited_255.jpg

Hope this helps (remember to rate and comment this).

Dec 16, 2010 | 2000 Mercury Sable

2 Answers

94 Mercury Sable


either your carburator needs cleening or your distributor is off a little { I promote safe clean work and eye protection-where your Safety Glasses! }
~ Dan Herzberg~

Mar 04, 2010 | 1994 Mercury Sable

1 Answer

A mercury sable 2002 crankshaft diagram, i need to know how to disassemble the crankshaft from the engine?


You must remove the transmmission. then if you can make enough room by releasing the motor mounts and placing two by fours under them you'll be able to gain acess to drop the oil pan. Drain it, first of course. After which, you'll need to remove the timing belt/chain cover. But before this you'll need to remove the waterpump, power steering pump, A/C if so eqipt,and the alternator. Then you'll be able to remove the timing cover. Line up all timing marks and remove the belt/chain. Then you may have to remove the oil sump tube and screen "IF" it is in the way of dropping the crankshaft. Loosen the crank. bearing bolts in a military rotation from center to out side. Keep each bearing cap in the exact position it came from the engine block on a diagrammed piece of cardboard. You should then be able to remove the crankshaft.Reverse the order for replacement.Put some bearing grease on the new bearings to keep them in place while reassembling the engine. Good Luck!, Dana

Aug 25, 2009 | 2001 Mercury Sable

1 Answer

94 Mercury Sable is stuck in neutral


shifting linkage is shot...time to see a mechanic($80-125)

Jun 14, 2009 | 1994 Mercury Tracer

1 Answer

Need spark plug gap for 94 Mercury Sable 3.0L


Listed in the owner's manual and under the hood on a placard. Also the parts store where you buy the plugs can supply this info.

Mar 18, 2009 | 1994 Mercury Sable

1 Answer

Need to change oil pump in a 98 murcury sable 3.0 ohv


i am working on the same thing on somebody else's car and trust me it is alot of work. you have to remove all the pulleys and accessories, the valve covers, oil pan, and u have to do all this just so u can remove the front engine cover. unlike most cars where the oil pump is located in the oil pan, this is mounted in a weird position and it is rotated by the crankshaft. i am not yet finished but i know once i get the front engine cover off i have to remove the timing chains also. in my opinion it is not worth the time or the money. i hope somebody finds this information useful.

Dec 13, 2008 | 1998 Mercury Sable

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...