Question about 2003 Audi A4 Cabriolet

3 Answers

Audi A4 2003 Change RH frontIndicator bulb

How do I get the headlight cluster off so I can change the indicator bulb. Can remove the 2 top bolts but still unable to remove the unit

Posted by on

  • arnals Aug 20, 2008

    Hi I managed to work out how to remove headlight cluster. Need to remove the air intake pipe that sits next to the radiator and loosen the bolt (not remove it) below the pipe.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

I've just replaced mine so here goes. Undo the top two bolts first. Then remove the two screws above the radiator holding the air intake ducting in place and gently pull out the air intake pipe and move to the back of the engine, exposing the rear of the lightbulb housing. To the rear of the lightbulb housing is a bolt. You should only need to loosen the bolt and this will allow the lightbulb unit to be pulled forward clear of the car. On the back of the housing you will find a cover, remove the clip retaining the cover and fold it away, exposing the rear of the light bulb.

Posted on Oct 10, 2008

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Enter through the wheel arch mud flap. Put your steering on hard left hand turn. Pull out the wheel arch section ( flexible and easy to manipulate.) The box is there in front of you to unclip and pop in a new bulb. Audi A4 2003 on

Posted on Jul 07, 2012

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Audi Master
  • 2,122 Answers

I'll Do some research and try to let you know....something for you to keep in mind....Inspect it and carefully look around it to try and find out how it's made and how it works....maybe you'll find out....
Regards
Johngee10

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace front headlight


Headlights Removal & Installation WARNING
Halogen bulbs contain a gas under pressure. Handling a bulb improperly could cause it to shatter into flying glass fragments.
To help avoid personal injury:
  • Turn off the headlamp switch and allow the bulb to cool before changing bulbs. Leave the headlamp switch off until the bulb change is complete.
  • Always wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • Do not drop or scratch the bulb. Keep moisture away.
  • Place the used bulb in the new bulb's carton and dispose of it properly. Keep halogen bulbs out of the reach of children
To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • LH and RH engine under covers
    • RH and LH Front fender liners
    • Front bumper cover
  3. 2 bolts and disconnect the connectors
  4. Headlight assembly by pulling it forward
  5. To Install:
    1. Install or connect the following:
      • Headlamp assembly
      • 2 bolts and connector
      • Front bumper cover
      • LH and RH front fender liners
      • LH and RH engine under cover
2997275.gif

Jul 25, 2009 | 1998 Toyota Camry

1 Answer

How to change a marker light bulb


to change the turn signal bulb on the headlight there is usually either a screw or tab that releases parking light lense from headlight. to just completely remove the headlight there are the two screws up top and also two lower if we are taking about the right side(drivers side, standing in front of vehicle) one of the screw is to the right side down near the inner fender, it is even with the bottom of the headlight. the other screw can be seen between the headlight and the radiator support about in the same area just opposite the other side. take a flashlight with you, not too hard to see

May 03, 2009 | 2003 BMW 325

1 Answer

How do you change a front right park light on an audi A4 2003


The easiest way is to remove the headlamp assy.  To do this removed air duct on RH side. remove 2 philips screws and pull up on other end at air filter box.  Next you will see 2 Torx T30 bolts that are holding to headlamp mouting brackets.  remove these completely.  Get a flashlight and look down inside eng bay you will see 2 more mouting points w/ t30 bolts.  loosen but dont entirely remove these.  Slide headlight out.  The park light socket has a big fin style tab grab firmly and twist counter clockwise.  Be sure after removing the bulb that the socket contacts aren't burnt up.  If they are you need a new socket and bulb.  Before reassembling test lights to make sure they work properly and install in reverse order of removal. 

Apr 25, 2009 | 2002 Audi A4

2 Answers

How to change bulb in headligth of volvo v70


For the RH headlight, First remove the top cover of the ECU module just behind the headlight. Then remove the middle section leaving the ECU in place. Both parts are just clipped in so should come out fairly easily. You will then be able to get access the the headlight bulb, release the spring clip at the top (using a mirror helps) and the bulb should come out.
For the LH side remove the air filter housing.

Mar 21, 2009 | 2007 Volvo V70

1 Answer

Replacement of headlights bulbs


1] remove th headlight assy. by removing the bolt on top of the assy and the 2 rod retainers.
2 ] remove the electrical connector from the headlamp bulb cover
3] rotate the bulb cover counterclockwise and remove cover
4] disconect the bulb connector
5] rotate bulb retainer counterclockwise and remove th ring
6] remove the bulb using a slight rocking motion
7] reverse proceedure to install

Feb 22, 2009 | 2005 Ford Taurus

1 Answer

Audi A6 Xenon headlamp bulb change - UK Offside





Headlights, Removing and Installing

Removing
  • Remove front bumper.
  • Remove both Torx bolts (T30) -1-.
  • Remove interior Torx bolt (T30) using 1/4"-Torx-bit insert and extension.
NOTE: If necessary, use magnet to remove bolt.

  • Disconnect multi-function harness connectors for headlights.
  • Turn headlights -2- toward center of vehicle and remove from chassis toward front.
Installing
Installation is reverse of removal, noting the following:


  • Adjust dimension -a- via plastic bolt at new headlight.
NOTE: Determine dimension -a- at plastic bolt of old headlight, when being replaced
  • Engage headlight in area of center of vehicle in guide -2- via pin -1-.
  • Always align headlight according to contours of chassis (gap dimensions) and secure.
  • Adjust headlight after installing.
Tightening torque

Component Nm
Headlights to lock carrier 6



Repair Kit For Headlight Housing, Installing

NOTE:
  • Headlight mounting tabs that have broken off can be replaced by installing the repair kit. Complete replacement of the headlight is therefore not necessary.
  • Different repair sets are available for the left and the right headlight.
  • Remove headlight with broken mounting tab.
    • Remove remains of the broken mounting tab -1- at location marked with the arrow.
    • Place mounting tab -2- of repair set onto the edge (arrow) of the headlight housing and secure the tab with two screws -3- from rear.

Feb 09, 2009 | 2004 Audi A6

1 Answer

Driver Side turn Signal Bulb


There's one more "hidden" bolt. Above and behind the corner of the headlamp, along the top ridge of the fender, there's a hole in the fender lip. Shine a flashlight down in there and you'll see the head of the third bolt. Remove that, and the headlight assembly will slide forward so you can change the bulb.

Jan 03, 2009 | 2001 Audi A4

3 Answers

Change the Front indicator on an Audi A4 2001


Take out the two Torx bolts on top of the headlight assembly. Then there is a third hidden bolt. Look through the holes in the top front of the fender, above and behind the headlight's turn signal portion (you'll probably need to shine a light in there) and you'll see the third bolt. Remove that and the headlight pulls straight forward and out. Then you can change the bulb.

Dec 09, 2008 | 2001 Audi A4

3 Answers

Side light bulb change on hyundai terracan


hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Nov 23, 2008 | 2003 Hyundai Tucson

2 Answers

2000 Audi a4 headlight bulb replacement


The easiest way to do it is to pull the headlight out of the car. This isn't hard, but you'll have to have a T30 Torx bit to do it. There are three bolts that secure the headlight. Two are on top of the headlight - you'll see them right up there on top when you open the hood.

The third is harder to find. Look where the outer upper corner of the headlight meets the top of the fender, above the corner indicator. There is a lip on the fender that runs all the way back to the base of the windshield, where the edge of the hood sits when it's closed. There is a round hole in that lip near the headlight (just behind it). Shine a light down in there and you'll see the third Torx bolt. Take that out and you can slide the headlight assembly forward. You shouldnt' have to take it fully out of the car, just take the bolts out and move it forward.

Then remove the dust cap on the back of the headlight, pop the connector off the bulb, undo the spring clip holding the bulb, and remove it. Install the new bulb (wipe down the glass portion with your t-shirt to get any skin oils off it, as they'll burn it up quickly), and then reassemble in the reverse order.

Nov 20, 2008 | 2000 Audi A4

Not finding what you are looking for?
2003 Audi A4 Cabriolet Logo

2,006 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...