Question about 2000 Ford Windstar

1 Answer

Radio problems i put my factory radio back in my 2000 windstar now i need a code so the radio will work correctly

Posted by on

  • billy reynolds
    billy reynolds May 11, 2010




1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

If its not in the glovebox with the book then its to the dealer my friend

Posted on Sep 03, 2008

  • patrick hopkins Sep 20, 2011

    you can also find a PDF version of the manual on the internet for free - do a google search for "ford windstar pdf owner's manual". You'll have to sort through a couple of pages of bogus hits, but you should be able to find it.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Battery dyes after not running 48 hrs+ ? 2003 Windstar minnewan.

There may be a factory service bulletin (FSB) for your Windstar that can correct the problem. It took three battery changes and replacement of a rear wiring harness to fix my 2000 Windstar. Also, using the rear blower and leaving it on with the vehicle shut down may be the source of the problem

Oct 12, 2013 | 2003 Ford Windstar

1 Answer

I have a ford windstar 2000 LX and it won't start! Please help me!!

Ok first you need to make sure that the battery was put back in correctly. Positive terminal to positive battery cable.Then if that is correct, check the main fuse's right next to the battery area, they are large and square ensure non of these are broken, or fused.Check all the fuse's in the other fuse box in the engine bay area and also inside the vehicle.
Let me know how you get on.

Mar 21, 2012 | 2000 Ford Windstar

2 Answers


a lot of times factory defaults on the radios is something like 0000 or 1111 or something like that. If not, you can pull the deck out and reset it.

Mar 14, 2012 | 2000 GMC Yukon Denali

1 Answer

Battery good but no power to the starter or relay box 2000 ford windstar radio works turn ignition on get nothing 3.8 eng

Do you know what a starter sylonid is? it should be near the battery its round and has two or three post comeing off of it if you put your key in the ingition and turn it but don't start it and go back under the hood take a screw driver and cross the two main post on the sylonid if you van starts you need to replace that part! most likely your problem!

Jan 11, 2011 | 2000 Ford Windstar

2 Answers

Radio wires differ from the speaker to the radio

This is the most common problem with self installs.The best thing to do is to get the car radio installation plug,it will plug into the factory plug for your factory radio and will give you a color coded pigtail to wire into that usually matches up perfectly with new aftermarket car radios.If the wires are already cut then you best bet is to extend the wires so that they are easy to work with hookup the power,ground,antenna and try dirrerent combos to isolate each speaker and label the wires accordingly.

Jan 01, 2010 | 1998 Ford Windstar

1 Answer

The radio is in SAFE mode....

It has to be the wrong code. You have to take in to the VW dealership, (because of so many stolen radios), they will have to verify your registration. Then they will remove your radio, get the serial number put it in to VW hub<( dealership only VW repair site), and retrieve the correct code. Even though the code shown is in your owners manual should have been the correct code sometimes radios get switched. Question at the end you said you pressed seek- did you hold the right lower arrow button, (scan), in till radio began to play?

Dec 31, 2009 | 2000 Volkswagen Beetle

1 Answer

How do I remove the radio from a 1998 Windstar

If its the factory Ford Radio then you'll need a pair of these removal tools:

Should be about 5bux or less from your local Wally World.

Very simple-
Put the tool in- 1-per side.
Push outward while pulling back.

Jul 11, 2009 | 1998 Ford Windstar

2 Answers

Factory stereo code

Factory radio codes are an anti-theft deterrent, they are unique to each radio and car serial number, in order to get the code the dealer will have to access the manufacturers data base, you will need to pull the radio and record the radio model number and the serial number of the chassis of the radio and take it to the dealer, they will not in most cases give the info out over the phone, this would defeat the whole purpose of the code.

Oct 18, 2008 | 2000 Mitsubishi Eclipse

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

230 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides