Question about 1992 Honda Accord

1 Answer

1992 Honda Accord lx

Need to know the direction to loosen crank shaft bolt.

Posted by on

  • Anonymous Mar 13, 2014

    CRANK BOLT CANT LOOSEN

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 702 Answers

Sound like you have the typical "frozen" crank bolt. To remove it, it's counter clockwise. What you do to remove it when it's frozen, pull #1 spark plug out, rotate crank so #1 piston is at the bottom of the cylinder. Now take a long piece of rope and stuff it into the spark plug hole as much as you can. Use a screwdriver to keep stuffing rope into cylinder. The rope is now a piston stop. When turning the crank counter clockwise to remove it, you'll feel the crank stop. Now you can crank on the wrench to break the bolt loose. I use a long 1/2" drive breaker bar, long 1/2" extension, and a jack stand to support the extension and with a jack handle over the breaker bar, pull hard and you'll hear a loud pop. At this point the bolt will break loose for you. Don't worry you will not break the crank bolt doing this. After the bolt breaks loose, rotate the crank clockwise again just enough the remove the rope.

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the bolts holding distributor down 1987 Honda accord. Try to loosen them to adjust timing


no engine size stated, wow.....

Fig. 1: On some engines, the distributor hold-down bolt is covered with a cap

all this is in the FSM.
first google hit
http://images.cmsnl.com/img/partslists/honda-accord-1987-3dr-lxi-ka-distributor-pgm-fi-tec_medium00027023E__0503_551f.jpg


http://www.justanswer.com/honda/34ysu-show-set-timing-1987-honda-accord.html


or see photos of 4 engines, in real FSM.
see 57.56mb manual 86-89 here page 24-6
http://hondatech.info/downloads/Auto/Manuals/Accord/

shows the actual clamp bolts.

Jan 09, 2014 | 1992 Honda Accord

1 Answer

Vss 1995 honda accord lx manual transmission


The speed sensor located near the drive shaft from the gearbox with a 3 wire n a 10mm bolt.. Try look somewhere where the drive shaft come out from ur gearbox

Feb 01, 2013 | 1995 Honda Accord

1 Answer

How do u change the timing belt on a 1990 4 cylinder honda accord?


Disconnect the wire harness at the distributor.Remove the spark plug closest to the drivers side front tire. Place the palm of your hand over the valve covers empty spark plug hole and have a helper crank the motor over until air pressure pushes past your the palm of your hand. Next, look at the cam shaft wheel and note the direction that the arrow is pointing, the arrow should be pointing straight up IN RELATION TO THE ENGINE not the earth. If it is not, you will need to manually rotate the engine till the cam wheel is infact pointing straight up. Next, Jack up the front of the car and support it with jack stand and remove the front drivers side tire.Next, support the weight of the engine with a floor jack remove the motor mount closest to the drivers side tire To remove it you will need a deep 17mm socket on a heavy duty breaker bar. Next, loosen and remove the power steering belt and alternator belts. To loosen and remove the belts you will need a 10mm wrench and a 12mm wrench. And also a 14mm or 15mm wrench. Next, use a 19mm socket AND an air powered IMPACT wrench to remove the bolt holding on the crank shaft pulley. Next, remove the crankshaft pulley. Next, use a 10mm wrench and/or 10mm socket and remove the bolts holding the plastic engine side cover. Next, loosen the 14mm or 15mm bolt which secures the 2 belt tension wheels. Next, LOOSEN the 10mm bolt that is on the balance shaft tensioner. The balance shaft is the cogged wheel with a small timing mark dot on the side of the wheel. Next, loosen the 10mm bolt on the timing belt tensioner. It's obvious what wheel is the timing belt tensioner. Next, remove the 12mm bolt on the back side of the block (near the balance shaft) a little bit of oil will drip out, this 12mm bolt will allow a long bolt to be inserted into a recessed channel of the balance shaft. This recessed channel is needed to lock the balance shaft in place. A bolt from the air conditioner works great for locking the balance shaft in place. You're basically just pushing the bolt in a hole to keep the balance shaft from spinning.890a27a.jpg Next, remove both the balance shaft belt and timing belt. Then reverse the procedure to complete the new belt installation. EXTREMELY IMPORTANT!!!!!!!!! PLEASE NOTE, the oil pump wheel furthest to the left (closest to the radiator), has a timing mark on the flat face side of the wheel, that timing mark has to be pointing directly to the 9:o'clock position in relation to the engine. The cam wheel has an arrow on the side of one of the "spokes" ...make sure it is pointing straight up in relation to the engine...straight away from the crank shaft. Put the crank wheel on with the arrow pointing straight up to the center of the cam wheel.

Jun 28, 2010 | 1990 Honda Accord

1 Answer

I have a 92 honda accord LX. How do i remove and replace the alternator?


Unplug the battery
Loosen and move the power steering pump out of the way (don't disconnect the hoses to it)
Loosed the bolts on the alternator (should be a 14mm on the top bolt, then there will be another lower (hard to reach 12mm bolt) where it pivots. Then, on the lower front of the alternator, there will be two 10mm bolts visible for the alternator belt tension bracket, loosen the RIGHT one as that will release the tension on the belt. You may need to bang or pry to get the alternator to swing out even if you have all the bolts out. They like to lock in there.

Jun 13, 2010 | 1992 Honda Accord

1 Answer

How to tighten drive belt in my 92 honda accord LX?


if it gets louder when the lights are on that means its the alternator belt,and you will have to look under the alternator there you will find the manual tensioner you have to loosen the mounting bolt in order to tighten it with the long tensioner bolt.

Apr 04, 2010 | 1992 Honda Accord

1 Answer

Crank shaft harmonic balencer bolt


THe Harmonic balanced bolt is loosened by turning it counter clockwise. It is recommended that you get the special tool to hold the harmonic pulley stationary while the bolt is loosened or tightened. However the bolt can be loosened if you use an impact socket and a very strong breaker bar and place it against a strong part of the frame and just bump the engine over very carefully with the high voltage coil wire disconnected so that the engine won't start when you bump it over with the starter and make sure the socket and the breaker bar are very secure when doing this. I recently bought the special Honda wrench from Snap-On tools and it works great for this, but it's very expensive but it's the only way to hold the Harmonic Pulley sufficiently in order to tighten it back to the recommended torque. Which can be several hundred ft pounds, see the service manual for the exact torque.

Aug 23, 2009 | 1992 Honda Accord

3 Answers

How do I loosen the bolt on crank shaft?


Hi Manuel

The bolt comes off, in an anti clockwise direction.

I normally put a socket on an extension bar, with metal tube, to extend the length, on to the crank pulley bolt.

Secure under the vehicle with wooden block, and spin he starter, this will loosen it off no problem.

But this procedure must be carried out, before the cam belt timing is disturbed.

Airgun can be used to replace the bolt.

Good Luck !

A FixYa rating would be Nice......Thank you ! John.



Feb 16, 2009 | 1999 Honda Accord

3 Answers

I need the specs to set the timing or a how to instruction to set


put motor TDC on #1 which is the furthest away from the distributor take motor mount off and support the front of motor with a jack. #2 take off your drive belts power steering and ac etc. Now lower the jack down a little and take off valve cover and power steering pump,set aside and remember were your bolts go.#3 take off timing cover 10 mm bolts all around the out side of the cover take top off out the top and put a 3/4 socket on a impact and take the bolt out of the center of the crankshaft take the crank pully off and remove bottom part of timing cover out through the bottom raise or lower the jack as needed#4 now their is a back balance shaft bolt in the back of the motor its a bolt take the bolt out and put a screw driver through there to hold the balance shaft from turning and getting out of time note make sure it is the bolt behind the not the round bolt with the hex in it the bolt in the block directly behind that round bolt. Put key way pointing straight up on cam gear and crank gear do this before removing old timing belt or balance shaft belt the front balance shaft has a notch cut out on the shaft that runs the gear put it straight up.#5 loosen tensioner and take the belts off. Now put your timing belt and balance shaft belt back on make sure everything stays in time nothing moves.

Jan 09, 2009 | 1993 Honda Accord

1 Answer

Where does the transmission fluid go in a 1992 honda accord lx st


in the same place that you check the fluid you will probably need a very small funnel

Jan 09, 2009 | 1992 Honda Accord

1 Answer

Thermostat in honda accord LX 1992


The hose that goes from the radiator to the front of the motor. There are two bolts on the engne block. The thermostat is located in there.

Dec 20, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1992 Honda Accord Logo

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...