Question about Acura RL

1 Answer

When I start my ignition a warning message comes on, istead of my navigation system, telling me that my navigation door is open or the DVD is not installed,, where will I find this navigation door? I cannot get any of my navigation system to activate until this matter is resolved, I turned the car off and then on again, but the problem continues.. J. Magnum

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 191 Answers

What is the make and the model you are using for the navigator ?

Posted on Aug 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

7 dings and a beep when starting 2000 ford explorer? what does that mean


NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with a scan tool.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition - Continuous Chime, 120/Min. 740 Hz Headlamps On - Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) - 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.

Feb 12, 2015 | 2000 Ford Explorer Eddie Bauer

1 Answer

Central locking disengages then engages while i am driving


it sounds like your ignition (a box where many switches open or close when you start the car) they get bad connections after a decade or so

Nov 13, 2013 | 2003 Renault Megane

2 Answers

How do I reset and turn off the "Maintenance Required" warning message on my 2006 Lexus LS 430 with built in navigation and radar cruise control? Many thanks.


normally disconnecting the battery for about ten minutes then reconnecting is enough to reset the computer and get the light to go out. although is there is a existing problem i will come back on after about 10 minutes of driving.

Apr 09, 2011 | 2006 Lexus Ls 430

1 Answer

Warning signal that lights are on or keys in the


this is a very common problem and it is the driver door latch/actuator. the switch that tells the body control module when the door is open or closed is stuck in the closed position. if you live around grand rapids michigan i have one on sale on craigslist for 75. at the dealer it will cost you about 170.

Mar 23, 2010 | 1999 Volkswagen Jetta

2 Answers

Possible ignition switch problem? 99 Explorer


key chime sounds if the little tab is grounded where the key contacts it. The theft light is supposed to blink when the system is armed to let you know it is armed. That's normal.

What do you mean by auto door locks won't unlock? The remote doesn't work? the door lock/unlock button on the door trim panel? Do they lock ok? Or, just unlock doesn't work?
-----------------------------------------------------------------------------------------------

NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with New Generation STAR (NGS) Tester.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition — Continuous Chime, 120/Min. 740 Hz Headlamps On — Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) — 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.
------------------------------------------------------------------------
  1. NOTE: The generic electronic module (GEM)/central timer module (CTM) must be reconfigured upon replacement. Refer to the New Generation STAR (NGS) Tester help screen on the configuration card to program the Tire Size, Axle Ratio.
    The power windows system and rear window defroster system are (GEM) controlled systems.
----------------------------------------------------------------------------------------------
  • All Windows Operate With the Ignition in the OFF Position
  • Circuitry.
  • Accessory delay relay.
  • CHECK the accessory delay relay; REFER to Component Test. If OK, REPAIR circuit 400 (LB/BK). If not OK, REPLACE the accessory delay relay. TEST the system for normal operation.


-------------------------------------------------------------------------
report back

May 06, 2009 | 1999 Ford Explorer

1 Answer

Warning bell won't stop sounding


Section 13-09: Gauges, Warning Devices — Chime System 1996 Windstar Workshop Manual
DESCRIPTION AND OPERATION Warning Chime Systems Three distinct sounds are used to indicate the area of concern. Seat belt warning generates 1 chime per second
key-in-ignition generates 2 chimes per second
headlight on generates 4 chimes per second.
Key-In-Ignition Warning The key-in-ignition warning will sound when the driver's front door (20125) is opened with the key in the ignition switch. It will continue to sound until the key is removed, the front door is closed, the ignition switch is turned to START or the vehicle speed is over 24 kmh (15 mph).

Safety Belt Warning When the ignition switch is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
  • The safety belt warning indicator lamp (10C859) will activate for 60 seconds or until the driver's safety belt is fastened. Both the chime and lamp activate at the same time.
Anytime the ignition switch is released from START and returns to RUN while the safety belt lamp or chime is activated, the safety belt warning lamp or chime will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Headlamp Switch On Warning The chime will be activated if the headlamps or parking lamps are ON, the key is not in the ignition and the driver's door is opened. The chime will sound at a rate of four per second.

Apr 23, 2009 | 1996 Ford Windstar

1 Answer

2001 lincoln navigator rear suspension?


Here is how to tell if system is working.Get into the vehicle and close door. Set ignition switch to on position and move the gear shifter to neutral. After a few secs. you should hear the compressor turn on. If it comes on then put shifter back to park leave ignition on and exit vehicle. Compressor will stop when you open the door but should start back up in a couple of secs. after you close the door. You can then walk around the vehicle and listen for leaks.
If compressor does not come on there are 3 fuses and a solid state relay that controls it along with the module.
The 3 fuses are no. 109(50amp) in the battery junction box under hood.This is the direct feed to compressor thru the solid state relay. The other 2 fuses are located in the interior fuse panel and they are no. 6 (5amp) and no. 12(15amp).
What we usually see though if compressor does not run is either a bad compressor or the solid state relay. They both are rather expensive so I would have an experience tech look at it then.
However If you feel confident enough and have a voltmeter or test light respond back and I will tell you which wires to check.

Mar 12, 2009 | 2001 Lincoln Navigator

1 Answer

Key on engine running trouble code 55


Warning Chime Systems The generic electronic module (GEM) will sound the following warnings:
  • key-in-ignition warning
  • safety belt warning
  • headlamp switch ON warning
  • door ajar warning
------------------------------------------------------------------------------------------------
Headlamp Switch On Warning The generic electronic module (GEM) sounds when the driver door is opened while the headlamp switch (11654) is in the PARK or HEAD position, and continues to sound at a rate of 4 chimes per second until the headlamp switch is turned off or the driver door is closed.
  • When the headlamp switch is in the PARK or HEAD position, power is supplied through Circuit 293 (O/R) to the GEM.
  • When the driver door is open, the driver door open warning lamp switch (10B997)is closed and ground is supplied to the generic electronic module (GEM).
A delayed headlamps on repetitive chime will sound for a period of three seconds beginning twenty seconds after the key is turned to OFF, LOCK or ACC, the headlamp switch is in the PARK or HEAD position, and the driver door is closed. Delayed headlamps on is terminated by opening and closing the driver door again.
---------------------------------------------------------------------------------------
Door/Liftgate Ajar Warning The door/liftgate ajar warning functions as follows:
  • The generic electronic module (GEM) sounds a warning tone for one second when any vehicle door, liftgate window or the liftgate is ajar without any other door already open and the ignition switch is in the RUN position.
  • Power is then supplied through Circuit 627 (BK/O) to the door ajar warning indicator lamp which remains illuminated until all doors are closed or the ignition switch is no longer in the RUN position.
----------------------------------------------------------------------------------------------
Key-in-Ignition Warning The generic electronic module (GEM) sounds when the LH front door is opened with the key in the ignition switch and continues to sound until the key is removed or the door is closed.
  • When the key is in the ignition switch, the ignition key warning switch terminal and wire (11A128) is closed and ground is supplied through Circuit 158 (BK/PK) to the generic electronic module (GEM).
  • When the LH front door is open, the LH front door open warning lamp switch (10B997) closes and ground is supplied through Circuit 57 (BK) to the generic electronic module (GEM).
-------------------------------------------------------------------------------------
Safety Belt Warning When the ignition switch is turned to RUN or START from the OFF or ACC position and remains in RUN or START, the chime will sound for six seconds or until the safety belt is buckled. The safety belt warning indicator lamp (10C859) will turn on for 60 seconds, or until the LH front safety belt is fastened. Both the chime and lamp activate at the same time. If the safety belt is buckled when the ignition key is turned to RUN or START from OFF or ACC, the lamp will prove out for two seconds, but chime will not be activated. Any time the key is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed, or the safety belt is buckled.

Feb 25, 2009 | 1999 Ford Taurus

1 Answer

2003 Jetta Fuse diagram


When you open the driver door does the little light in the door panel come on. Or do you notice if the dome light comes on when set to door open setting? If it's a gli it has electric door locks and remote. If they don't come on with the door open the door is not sensing being opened by the microswitches in the latch. When you unlock the door with the remote and open the door without putting your key in the ignition the doors probally will relock (just make sure the key isn't in the car alone) about 15 seconds later. A normal effect as safety when the door isn't opened the car will relock. If this is the situation you can start by checking the wiring in the accordian between the door and frame for cut wires and the connections in the kick panel behind the hood release, but 99% of the time it is a defective latch.

Oct 27, 2008 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

660 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...