Question about 1982 Ford F 250

2 Answers

4 wheel lock hub system for a 1982 ford f 250

I dont know how to take apart the hub lock system and when i am in 4 wheel drive passanger side front wheel dont spin with the rest

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

It has an open differential it will only spin one side either right or let depending on traction and a few things if it is spinning one front tire in dirt mud or snow everything is probly just fine

Posted on Jan 06, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Tell me how to take a hub off a 1982 ford 150

Posted on Sep 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 ford f250, four wheel switch locked in in cab, no front wheel drive, lock in both front wheel hubs and now have 4 wheel drive. Flip off switch inside and no longer in 4 wheel drive.


I really don't know quite how to tell you this. Everything seems to be working just fine buy your question. When your using 4 wheel drive, you engage the hubs first, then push the 4 wheel drive button or turn the switch. Ease it in and out of gear or shift on the move and you should be in 4 wheel drive at this point. To take it out of 4 wheel drive, reverse this procedure. Turn the switch off and ease forward and you will be out of 4 wheel drive. If your not going to use your 4x4, turn the hubs out to reduce ware on the axles. If you will be using 4x4 again soon, leave the hubs in and all you have to do is turn the switch to 4x4 and your set to go. I hope I explained this well enough. Good luck.

Feb 10, 2015 | Ford Cars & Trucks

1 Answer

Toyota tacoma stuck in 4 wheel drive ( but just the front drivers side hub/wheel


I need to know the year and if your 4X4 is electronic or manual shifter.
Most older 4X4 Toyotas have manual hub lock.you will find on the hub lock and unlock position2013-09-15135605_zps8d906c79.jpg

Mar 23, 2014 | Toyota Tacoma Cars & Trucks

1 Answer

I have a 1996 ford f-250 4x4 i have a shift in the floor but my wheels won't engage


ARE THE HUBS LOCKED IN FIRST? FOR YOU HAVE TO LOCK AND UNLOCK THOSE HUBS FROM THE OUTSIDE.. EACH TIME YOU GO INTO 4X4 AND WHEN YOU GO OUT OF 4X4 TO 2 WHEEL..DRIVE. OR YOU DON'T HAVE A FRONT DRIVE SHAFT GOING TO THE FRONT AXLE?? OR ITS BROKEN OR THE TRANSFER CASE IS BAD??

Feb 09, 2014 | 1986 Ford F 250

2 Answers

The driver side front wheel does not engage in 4 wheel drive


manual or auto hubs?how do u now it is not engaging?.u can lift the front end up in 4 wheel make sure hubs r engaged .rotate the tire by hand ,and check to see if the drive shaft is turning [from the wheel to the front diff] u most likely have a bad locking hub.if it is not turning ur front tire is not locked up

Dec 29, 2010 | 1994 Ford Bronco

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

1 Answer

Four wheel drive not engaging


Check the front wheel bearings for play and also while the wheel is off the ground lock the front hubs, grab the axle behind the wheel and see if it is engaged. If not then you will need to take the hub apart and find out what is broken.

May 29, 2009 | 1999 Ford F250 Regular Cab

1 Answer

2004 Ford F-150 extended cab FX4. 4WD problem


Your front hubs are automatic locking hubs, and the gears are hard nylon. These hubs break very easily, therefore causing you to lose your front wheel drive in 4 high, or 4 low. If you replace the hubs with "WARN (name brand) " manual locking hubs, you will never have the issue again. Of course, you will have to get out of the truck and manually lock the hubs, but they are metal gears, and much more durable. I've personally seen the issue several times, and changing the hubs has resolved the issue every time.

May 01, 2009 | 2005 Ford F-150

1 Answer

Ford F150 lost 4 wheel drive 2003 FX4


Take the hubs apart, inspect them, and clean them, especially the one that you heard a clunk, something might have broke in the automatic hub lock. Make sure everthing gets put back exactly the same, or you'll have more problems. If that doesn't work, then there is something wrong somewhere in the transfer case.

Mar 15, 2009 | 1999 Ford F150 Regular Cab

1 Answer

How does 4 wheel drive work?


Hi there , in order for your 4 wheel to work you have to drive a couple feet for everything to lock. If you are already stuck and you put it into 4 wheel, it won't engage. hope this helps you out

Dec 29, 2008 | 1991 Ford F250

1 Answer

Jeep YJ 1991 4 wheel drive


if u got automatic front hubs stop put in park pull 4x4 shifter into 4 wheel
manual hubs at front wheels turn the hub locks to the lock position and then pull the 4 wheel shifter inti 4 wheel
also look over drivers sun visor if the tag aint worn off the direction are there... have fun 4 wheeling and keep the rubber side down
rank, rate & vote for my solution

Dec 20, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

156 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...