Question about 2005 Toyota Avalon

2 Answers

How many bolts are in the intake manifold of a 2005 toyota avalon....we are trying to replace ignition coil e and cant get to it

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 2 Answers

Right! Just remove the grill covering the windshield wiper motor. Then remove the windshield wiper. There may be a small brace covering the #1 cylinder but it can be easily removed. Most of the bolts are all 10mm. and the rear coils are easily removed.

Posted on Jun 09, 2013

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 3 Answers

No !! Take off the grill in front of the windshield u can get to it from there

Posted on Dec 15, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the intake manifold on a 2000 toyota avalon


There's two intake manifolds on the engine. 1 for every 3 cylinders of the engine. You can see that there are 3 exhaust tubes that flow into one pipe on each side of the engine. The two pipes are where you have 02 sensors. See pic attached , Bank 1 sensor 1, bank 2 sensor 130a9a07c-6337-4b2d-aac5-fbacd3c57455.jpg 5f722f0b-c181-4c00-bcb5-e8fce99ce1b7.jpg

Jul 11, 2014 | 2000 Toyota Avalon

1 Answer

Where is the ignition module on a 99 plymouth voyager


Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Cars & Trucks

1 Answer

Where is the ignition module in a 99 voyager


Hi Eric:
Also called Ignition Coil, is located at the back of the intake manifold...

2_11_2012_12_07_40_pm.jpg

Fig.: remove the 2 lower ignition coil mounting bracket bolts...


2_11_2012_12_08_55_pm.jpg

Fig.: then remove the ignition coil and mounting bracket together from the engine.

Disengage the wiring harness connector from the ignition coil.
Disconnect the ignition wire from the coil.
Remove the coil mounting bracket bolts, then remove the coil and mounting bracket assembly from the vehicle.
The ignition coil can be separated from the mounting bracket.

To install:

If separated, loosely mount the ignition coil to the mounting bracket.
Loosely install the coil and mounting bracket assembly to the intake manifold. Tighten the coil mounting bracket-to-intake manifold bolts to 115 inch lbs. (13 Nm) and the ignition coil-to-mounting bracket fasteners to 96 inch lbs. (10 Nm).
Connect the ignition wire to the coil.
Engage the wiring harness connector to the ignition coil.
If removed, install the windshield wiper/motor module assembly.
Connect the negative battery cable.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 10, 2012 | Plymouth Cars & Trucks

1 Answer

Where are the coil packs located on an 04 Lincoln LS v8? I have traced the wires from the spark plugs, but cannot see where they lead...


This is for the 3.0L engine:

3.0L Engine
  1. Remove the engine appearance cover.
  2. To access the right bank ignition coils, remove the upper intake manifold..
  3. Disconnect the electrical connector from the ignition coils.
  4. Remove the bolts.
  5. Remove the ignition coils.

c17hydro_182.gif


To install:


  1. Replace the ignition coils.
  2. Connect the electrical connector to the ignition coils.
  3. Remove the upper intake manifold for the right bank ignition coils.
  4. Replace the engine appearance cover.


May 12, 2011 | Lincoln LS Cars & Trucks

1 Answer

Where would the pvc value be on a 300 chrysler 2006? also where would the spark plugs be located?


Positive Crankcase Ventilation (PVC) Valve Removal & Installation 5.7L Engine To Remove:
    1.The PCV valve is mounted into the top/right side of the intake manifold.

    2.The PCV valve is sealed to the intake manifold with two O-rings.

    3.Free the PCV valve by rotating counter-clockwise 90 degrees until the locating tabs align with the openings on the manifold.

    4.Remove the PCV valve by pulling straight up from intake manifold and clearing the tabs.

    5.Check the condition of two valve O-rings.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Inspect the PCV valve O-rings. Replace if suspect.
  3. Apply engine oil to the two O-rings.
  4. Place the PCV valve into intake manifold.
  5. Rotate the valve 90 degrees clockwise for installation.
6.1L Engine To Remove:
  1. The PCV valve is threaded into the right-front corner of the intake manifold.
  2. Remove the rubber hose from the PCV valve.
  3. Unscrew the PCV valve from the intake manifold.
To Install:
  1. Clean the PCV valve opening on the intake manifold.
  2. Check the condition of the PCV valve O-ring. Replace if suspect.
  3. Check the condition of the PCV valve threads and clean if necessary.
  4. Apply engine oil to the O-ring.
  5. Install the PCV valve into intake manifold.
  6. Install the rubber hose to the PCV valve.
prev.gif next.gif
The spark plugs should lead to the coil pack via a spark plug wire but may be hidden by a plastic cover.

The following details the ignition coil changing on the Chrysler 300:

2.7L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
  1. Install the ignition coil.
  2. Tighten the fasteners to 55 in-lb (6.2 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
3.5L Engine To Remove:
  1. Disconnect the negative battery cable.
  2. Remove the intake manifold.
  3. Use compressed air to clear the area around the ignition coil and spark plug.
  4. Disconnect the electrical connector from the ignition coil. NOTE: Loosen the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when loosening the fasteners.
  5. Remove the two fasteners securing the ignition coil.
  6. Remove the ignition coil.
To Install:
NOTE: Tighten the ignition coil fasteners by alternating back and forth. Do not lose the spacers under the coil when installing the coil.
  1. Install the ignition coil.
  2. Tighten the fasteners to 60 in-lb (6.7 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Install the intake manifold.
  5. Connect the negative battery cable.
5.7L Engine (2005) To Remove:
NOTE: Carefully note the position of each spark plug cable before disconnecting them so they can be installed in their original positions to prevent misfire.
NOTE: The throttle body intake air duct or intake air box may need to be removed to gain access to certain ignition coils.
  1. Disconnect the electrical connector from the ignition coil.
  2. Remove the secondary ignition cable from the coil.
  3. Use compressed air to clear the area around the ignition coil.
  4. Remove the two fasteners securing the ignition coil. Bolts are retained to coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Clean area around spark plug and coil mounting area with compressed air.
  2. Install the ignition coil.
  3. Tighten the fasteners to 105 in-lb (12 Nm).
  4. Connect the electrical connector to the ignition coil.
  5. Connect the secondary ignition cable to the coil.
  6. Install the air duct or air box if removed.
Ignition coil mounting bolts (5.7L & 6.1L engines) chry-02-57-263.gif

5.7L (2006) & 6.1L Engine To Remove:
NOTE: Each ignition coil, mounted on the valve cover, fires two spark plugs at each cylinder.
  1. Disconnect the negative battery cable.
  2. Use compressed air to clear the area around the ignition coil and spark plug.
  3. Disconnect the electrical connector from the ignition coil.
  4. Remove the two fasteners securing the ignition coil.
  5. Remove the ignition coil. Pull with a slight twisting motion to help release the boot seal with the spark plugs.
To Install:
NOTE: Apply a light film of dielectric grease to the inside of the coil boots before installation.
  1. Install the ignition coil.
  2. Tighten the fasteners to 105 in-lb (12 Nm).
  3. Connect the electrical connector to the ignition coil.
  4. Connect the negative battery cable.
prev.gif next.gif

Sep 24, 2010 | 2005 Chrysler 300

1 Answer

How do you take off a intake manifold


This is for the 4.6L motor...I'll post for the 5.0L and 5.8L....you didn't post your engine size so please pick the applicable motor:

4.6L Engine
CAUTION Fuel injection systems remain under pressure, even after the engine has been turned OFF. The fuel system pressure must be relieved before disconnecting any fuel lines. Failure to do so may result in fire and/or personal injury.

  1. If equipped with air suspension, the air suspension switch, located on the right-hand side of the luggage compartment, must be turned to the OFF position before raising the vehicle.
  2. Disconnect the negative battery cable.
  3. Drain the engine cooling system.
  4. Relieve the fuel system pressure as follows:
    1. Remove the fuel tank fill cap to relieve the pressure in the fuel tank.
    2. Remove the cap from the Schrader valve located on the fuel injection supply manifold.
    3. Attach Fuel Pressure Gauge T80L-9974-B or equivalent, to the Schrader valve and drain the fuel through the drain tube into a suitable container.
    4. After the fuel system pressure is relieved, remove the fuel pressure gauge and install the cap on the Schrader valve. Secure the fuel tank fill cap.
  5. Disconnect the fuel supply and return lines.
  6. Remove the windshield wiper governor (module).
  7. Remove the engine air cleaner outlet tube.
  8. Release the drive belt tensioner and remove the accessory drive belt.
  9. Tag and disconnect the ignition wires from the spark plugs. Disconnect the ignition wire brackets from the cylinder head cover studs.
  10. Disconnect the wiring from both ignition coils and the Camshaft Position (CMP) sensor. Tag and disconnect all ignition wires from both ignition coils. Remove 2 bolts retaining the ignition wire bracket to the ignition coil brackets and remove the ignition wire assembly.
  11. Disconnect the alternator wiring harness from the junction block at the fender apron and alternator. Remove the bolts retaining the alternator brace to the intake manifold and the alternator to the cylinder block and remove the alternator.
  12. Raise and safely support the vehicle.
  13. Disconnect the oil pressure sensor and power steering control valve actuator wiring and position the wiring harness out of the way.
  14. Disconnect the EGR valve to exhaust manifold tube from the right-hand exhaust manifold.
  15. Lower the vehicle.
  16. Remove and detach the engine/transmission harness connector from the retaining bracket on the power brake booster.
  17. Detach the A/C compressor clutch, Crankshaft Position (CKP) sensor and the canister purge solenoid wiring connectors.
  18. Remove the PCV valve from the cylinder head cover and disconnect the canister purge vent hose from the PCV valve.
  19. Disconnect the accelerator and cruise control cables from the throttle body. Remove the accelerator cable bracket from the intake manifold and position out of the way.
  20. Disconnect the vacuum hose from the throttle body adapter port.
  21. Disconnect both Heated Oxygen Sensors (HO2S) and the heater water hose.
  22. Remove 2 bolts retaining the thermostat housing to the intake manifold and position the upper hose and thermostat housing out of the way.
The 2 thermostat housing bolts are also used to retain the intake manifold.
  1. Remove 9 bolts retaining the intake manifold to the cylinder heads and remove the intake manifold. Remove and discard the gaskets.
  2. If replacing the intake manifold, swap over the necessary parts.
To install:
  1. Clean all gasket mating surfaces.
  2. Position new intake manifold gaskets on the cylinder heads. Make sure the alignment tabs on the gaskets are aligned with the holes in the cylinder heads.
  3. Install the intake manifold and 9 retaining bolts. Hand tighten the right-rear bolt (viewed from the front of the engine) before final tightening, then torque the bolts, in sequence, to 15-22 ft. lbs. (20-30 Nm).
  4. Inspect and if necessary, replace the O-ring seal on the thermostat housing. Position the housing and upper hose and install 2 retaining bolts. Torque to 15-22 ft. lbs. (20-30 Nm).
  5. Reconnect the heater water hose.
  6. Reconnect both HO2S wiring connectors.
  7. Reconnect the vacuum hose to the throttle body adapter vacuum port.
  8. Install the accelerator cable bracket on the intake manifold and connect the accelerator and cruise control cables to the throttle body.
  9. Install the PCV valve in the cylinder head cover and connect the canister purge solenoid vent hose. Reconnect the A/C compressor clutch, CKP sensor and canister purge solenoid wiring connectors.
  10. Reconnect the engine/transmission harness connector. Install the connector on the retaining bracket on the power brake booster.
  11. Raise and safely support the vehicle.
  12. Reconnect the EGR valve to exhaust manifold tube to the right-hand exhaust manifold. Torque the tube nut to 26-33 ft. lbs. (35-45 Nm).
  13. Reconnect the power steering control valve actuator and the oil pressure sensor wiring connectors.
  14. Lower the vehicle.
  15. Position the alternator and install 2 retaining bolts. Torque to 15-22 ft. lbs. (20-30 Nm). Install 2 bolts retaining the alternator brace to the intake manifold and torque to 71-106 inch lbs. (8-12 Nm).
  16. Reconnect the alternator wiring harness to the alternator, right-hand fender apron and junction block.
  17. Position the ignition wire assembly on the engine and install 2 bolts retaining the ignition wire bracket to the ignition coil brackets. Torque the bolts to 71-106 inch lbs. (8-12 Nm).
  18. Reconnect the ignition wires to the ignition coils in their proper positions. Reconnect the ignition wires to the spark plugs.
  19. Reconnect the ignition wire brackets on the cylinder head cover studs. Reconnect the wiring connectors to both ignition coils and the CMP sensor.
  20. Install the accessory drive belt.
  21. Install the engine air cleaner outlet tube.
  22. Install the windshield wiper governor.
  23. Reconnect the fuel supply and return lines.
  24. Fill and bleed the engine cooling system.
  25. Reconnect the negative battery cable.
  26. If equipped with air suspension, turn the air suspension switch to the ON position.
  27. Start the engine and check for leaks.
  28. Road test the vehicle and check for proper operation.
4dc9694.gif
4.6L engine intake manifold torque sequence—1996-98 Models

Nov 30, 2009 | 1997 Mercury Grand Marquis

2 Answers

How do you change the spark plugs for a 1999 toyota avalon


This isnt a simple job, its best that a experienced mechanic works on this. You will need special tools for access to the rear head. All sparkplugs in the 1MZFE motor are in the center of the cylinder heads. There are COPs (coil over plugs) atop the sparkplugs, these must be removed first.**With Engine Cold** Front head: 1.remove Coils 2.use 5/8th plug socket and extension w/ratchet turn ratchet counter clockwise till plug is loose. 3. install new plugs (make sure the plugs are properly gapped). Rear Head: Intake manifold must be removed (you need a very large allen wrench for the intake bolts removal). Once this is removed follow the same steps as the front head. Here is some illustrations on the 1MZFE engine: http://www.turboninjas.com/camry/eg2.pdf

HOPEFULLY THIS HELPS

Jul 19, 2009 | 1999 Toyota Avalon

3 Answers

Toyota Avalon 2000


You need to pull off the entire intake manifold/plenum assembly. The knock sensor is bolted to the inside of the cylinder block, it is in the middle of the culinder block.

Dec 29, 2008 | 1996 Toyota Avalon

Not finding what you are looking for?
2005 Toyota Avalon Logo

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

85104 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...