Question about Subaru Legacy

1 Answer

I need to know the torque specs for the axle to hub on a 97 subaru legacy outback...

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 382 Answers

Factory specs are 122 to 151 lbs.

Posted on Jan 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

97 Subaru legacy won't start and locks do not work. Battery is good and all fuses are fine.

take your ground wire off the battery and clean it with a wire brush it sounds like a ground problem

Dec 06, 2012 | 1997 Subaru Legacy

1 Answer

99 subaru outback legacy. I got a bad knocking noise in the front, its coming from the area flywheel & torque converter, I don't know what its called, some say its third member or transfer case or...

If the noise is coming from the area you say it could be loose torque converter bolts or a cracked flexplate. If you do not have one, a stethascope is available at the auto parts stores and that will help pinpoint the area where it is coming from.

Sep 02, 2011 | Subaru Outback Cars & Trucks

1 Answer

Oil pan bolt torque specs. for a 1998 Legacy Outback.2.5 engine?

Torque the oil pan bolts 36 to 40 in-lbs. starting from the center and working your way to the ends.

Nov 06, 2010 | Subaru Legacy Cars & Trucks

1 Answer

Torque specs 1995 subaru

Did you want the torque converter mounting bolt torque? If so, it is 17 to 19 foot pounds.

May 08, 2010 | 1995 Subaru Legacy

1 Answer

97 subaru legacy outback 2.5 vibration only at idle in gear

I would suspect a mount. Either motor or trans. Also check lateral mount on top of motor to firewall. Good luck and have a great day.

Feb 10, 2010 | 1997 Subaru Legacy

2 Answers

Disconected my battery cables.......lights flash

Regulator is bad or alternator is going out.

Sep 28, 2009 | 1997 Subaru Outback

1 Answer

Installing a catylic converter on a 2005 legacy outback wagon, torque settings, any tricks to install, problems to lok for?

how many miles?there is a recall now on 05 legacy outbacks,the recall calls for the shop to perform a catalyst deteriation test and depending on results one or both sets of catalysts need replacement and ecm gets reflashed check it out and by all means ,i know these convertors are expensive,do not get suckered by installing a aftermaket convertor they only last 3-6 months

Aug 16, 2009 | 2005 Subaru Outback

1 Answer

Replacing the front axle on a 93 subaru legacy

When I replace the axle halves, I run the Nut off till it is level with the shaft end. THen take a piece of wood and set it across the shaft and hit the wood with a hammer. Usually only takes one or two hits and pops right out.Then I remove the nut and finish removal . Hope this helps, Good luck and have a great day.

Mar 02, 2009 | 1993 Subaru Legacy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

259 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides