Question about 1996 Pontiac Sunfire

2 Answers

96 sunfire 2.2 Dumby Lights

When the car is started the cluster is lit like normal when you ingage into drive and start driving every dumby light comes on and the tacometer and the coolant temp gauge dont work but the speedometer and fuel gaue are still finction ive never heard of this before any suggestions???

Posted by on

  • chazmosis Jan 12, 2009

    I have the exact same problem described above... Happens when you shift out of park into any gear

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Http://www.automotivehelper.com/topic545921.htm

Make sure the secondary groundwire between the bottom of the battery tray and a ground point (The transmission housing) is in place. I replaced my negative battery cable and didn't replace this wire. This will cause these problems

Posted on Jan 12, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I've got the same problem except my car stopped running... i thinks its a corroded wire somewhere in the harness... but i dont know for sure mines been sitting in my driveway while i try to figure out why it wont start

Posted on Aug 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ilghts on cluster come on when backing up .can put shifter in neutral turn off and back on lights go out


sounds as if there is a short to ground in the shift column causing the lighting problem.

May 19, 2012 | 2000 Pontiac Sunfire

1 Answer

I need to know why the daytime running lites won't come on when I put my 2000 Sunfire in drive they blink 3 times and service lite turns on Relay or microprocessor?


The daytime running light module is built into the instrument cluster of your car and if all the lights work normally with the headlight switch then you need to replace the dash[instrument cluster].A dealer will need to program it whether it is new or used,so plan for that as well.

Apr 15, 2010 | 2002 Jeep Grand Cherokee

1 Answer

I have 2005 Sunfire and my horn recently will start going on it's own. I'll hear a little clicking and then the horn starts randomly going off I had to remove the fuze for it to stop, how can I fix this?...


I would change the horn relay it is most likely the cuplrit, I will look into the CEL and get back to you, the light icon is telling you that you are running on driving lights. which is normal.

Aug 03, 2009 | 2005 Pontiac Sunfire

1 Answer

Dodge Ram 1500 4x4 Engine code P 1687


No Cluster Buss Message is codeP1687. May be a cluster problem obviously but appears other things can cause it also. With price of a new or used cluster I would try a few things like pushing diagnostic button on dash, and let it go through the steps, as well as a battery disconnect for a few minutes then reconnect, just to see if you get lucky. if not, make sure you get assurance that whatever the repair shop says is wrong, if it doesn't cure the problem, you don't pay. Sounds like a lot of misdiagnosing being done on this . Sign up on the Dodge Truck forum, for more input. Good Luck

May 17, 2009 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

2001 4x4 1500 extnd cab .. dumby lites on code nobu5 in odmeter


IF THIS CODE IS NOBUS THEN I BELIEVE IT IS A COMMUNICATIONS PROBLEM WITH THE COMPUTER. CHECK THE FUSES FIRST. ESPECIALLY THE ONE FOR THE PCM(COMPUTER). ALSO CHECK THE CONNECTIONS ON THE PCM WHICH IS LOCATED ON THE PASSENGER SIDE FIREWALL AND HAS A BAJILLION WIRES COMING FROM IT. IT HAS THREE CONNECTORS THAT ARE HELD IN PLACE BY THREE BOLTS ON THE BACK OF THE COMPUTER. HOPE THIS HELPS YOU. PLEASE LET ME KNOW. GOOD LUCK

May 03, 2009 | 1999 Dodge Ram

2 Answers

2000 pontiac sunfire


You need to get a code reader to see if there is an error.

Sep 24, 2008 | 2000 Pontiac Sunfire

5 Answers

Switch off tire pressure warning light


From the manual: First find the reset button, located below the handbrake (emergency brake) lever. The button has an "exclamation mark in a tyre" symbol.

Make sure the pressures in all tyres are what you want them to be. 35psi all 'round is good for sporty driving.

Engine off. Turn ignition to the second position (ON) but don't start the engine.

Keep the re-set button pressed until the flat tyre indicator light on the dashboard COMES ON for several seconds.

Start the engine, and drive the car normally for several minutes. This will re-set the indicator to whatever pressures you have in the tyres. Hope this helps!!

May 15, 2008 | 2004 Mini Cooper

Not finding what you are looking for?
1996 Pontiac Sunfire Logo

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...