Question about Chevrolet Classic

1 Answer

What is a oil filter tube baffle on a 1967 327

Posted by on

  • piddleguy Aug 10, 2008

    Could it be on the bottom of the block ,above the oil filter( behind both plates that the filter screws into there is a hole that was perfect) but why plug up a oil line? Never had a problem like this and cant find one anywhere, or where it goes if I had it! Its just nuts. This is a 64 to 67 327. Casting # on the block 3892657 Thanks Ron

  • piddleguy Aug 10, 2008

    This is a spin on, no bolt. It very well could be a after market set up. I have a 400 to put in another Chevelle, took the filter of it a little bit ago and it was different. One plate, no hole besides the screw hole for the intake. Dont know. About ready to scrap a 300 bucks make over because of a 25 cent part! Thanks so much Ron

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 121 Answers

The only place I can think of there being a oil filter tube baffle is the suction screen on the oil pump pickup tube. This should be inside the oil pain, attached to the oil pump.

Posted on Aug 09, 2008

  • Rian Peters
    Rian Peters Aug 10, 2008

    Some of the older engines had a different oil filter attachment, after market plates came out and a spin on filter could be used, sorry I can not look up the casting number on the block. I will try and check into this, and get back with you. Non of the older units I worked on had two plates between the filter and block. Is this a spin on filter or a canister filter with a bolt through the center.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

NO OIL PRESSURE LIGHT GO OF BUT NO RESPONSE ON MY GAUGE , FITTED NEW OIL PUMP AND FILTER BUT STILL SAME TAPPET NOISE


What motor? If a SBC you can't just press on the oil pump pick up, you need to have it welded on or they come loose and fall off.
Some pumps need to be primed, I would put mine into pan of clean oil and turn pump until it started sucking up the oil before installing.
If it is a 3800 Buick you need to pack gears with vasoline, so different motors require different steps in order for oil pump to function after replacing it. There is also chance filter is bad, or relief valve is bad, more info would help us help you.

Feb 05, 2016 | Cars & Trucks

1 Answer

How do I get oil pan off on a 2000 Saturn LW300 V6 3.0L


The official shop manual reads :
Remove nose cone brackets bolts from oil pan.
Remove lower transmission flange to oil pan bolts.
Remove oil pan bolts.
Using designated pry points to break loose the seal. Bump the pan with a rubber mallet to loosen the pan from the engine block.
Remove oil pan.
By the illustrations, the only thing in the way is the oil pickup tube.... Good luck !
t

Nov 21, 2014 | Saturn Cars & Trucks

1 Answer

I need to change the oil and oil filter how mutch oil do i need and what grade for a citroen xsara 1587cc petrol


Oil filter replacement:

1. Removing:
"a" tabs
(1) Filter element protective cover
(2) Seal
(3) Filter element of the oil filter
(4) Plunger tube.
Untighten the filter element protection cover.
The filter element protection cover incorporates a 27 mm on flats Allen screw with 2 lugs at "a" which enable it to be held in a Facom S27 HLA socket.
Remove the cover (1).
2. Repair: When removing the filter element, the plunger tube ( 4) frees the oil return pipe, thus permitting the oil remaining in the filter element to return to the engine sump.
The filter element ( 3) and plunger tube (4) assembly should be replaced at every service.
Filter element protective cover : Tightening torque : 2,5 (0; -0,5) daNm. Proceed in the reverse order to removal.
11_10_2011_7_38_05_pm.jpg

Nov 10, 2011 | Cars & Trucks

1 Answer

I can't find the oil filter on my Boss's Avalon so it is setting in our main hanger at the small airport that I work at. I have drained the old oil out but I am baffled by where the oil filter is located.


It's in a cast aluminum container on the bottom of the engine toward the front passenger side,you will see a square hole. The filter is inside, it is a cartridge type filter. Filters are at your toyota dealer and come with 2 "O" rings, an adapter to drain oil from the housing, plus directions.

Oct 09, 2010 | 2010 Toyota Avalon

1 Answer

Where is the oil drain plug of a 2005 toyota sequoia ?


Look under the engine (not the transmission) for the drain plug on the engine oil pan.

The following is some information on how to change the oil pan:
REMOVAL & INSTALLATION 3.4L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain the engine oil.
  4. Remove or disconnect the following:
    • Engine undercover
    • Front differential, if equipped with 4WD
    • Oil pan, separate it from the engine using SST 09032-00100 and a brass bar
    To install:
  5. Apply seal packing to the oil pan.
  6. Install the oil pan to the cylinder block. Tighten the nuts and bolts to: 67 inch lbs. (8 Nm) WARNING
    If parts are not assembled within 5 minutes of applying time, the effectiveness of the seal packing is lost and must be removed and reapplied.
  7. Install or connect the following:
    • Front differential, if removed
    • Engine undercover
    • Negative battery cable
  8. Fill with engine oil.
  9. Start the engine and check for leaks.
4.7L Engine
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove the engine from the vehicle and mount it on a stand.
  3. Remove or disconnect the following:
    • Oil dipstick tube
    • Lower oil pan
    • Oil pan baffle
    • Upper oil pan
    To install: Fig. 1: Upper oil pan bolt location — 4.7L engine 7924sg75.gif

  4. The upper oil pan bolts are different lengths and are identified as follows:
    • A: 0.79 inch (20mm) w/10mm head
    • B: 0.98 inch (25mm) w/12mm head
    • C: 2.36 inch (60mm) w/12mm head
    • D: 1.38 inch (35mm) w/10mm head Fig. 2: Upper oil pan sealant application — 4.7L engine 7924sg74.gif

  5. Apply silicone sealant to the upper oil pan as shown.
  6. Install the upper oil pan and tighten the fasteners in several passes to the following specifications:
    • 10mm: 66 inch lbs. (7.5 Nm)
    • 12mm: 21 ft. lbs. (28 Nm) Fig. 3: Lower oil pan sealant application — 4.7L engine 7924sg76.gif

  7. Install or connect the following:
    • Oil pan baffle. Tighten the fasteners to 66 inch lbs. (7.5 Nm).
    • Lower oil pan. Tighten the fasteners in several passes to 66 inch lbs. (7.5 Nm).
    • Oil dipstick tube
  8. Install the engine.
prev.gif next.gif

Sep 01, 2010 | Toyota Sequoia Cars & Trucks

2 Answers

MY SUZUKI GET TOO MUCH WHITE SMOKE,BUT I HAVE PUT ENGIN FLUSH, CHANGE THE OIL AND THE OIL FILTER,ADD ANTISMOKE TO FUEL BUT NO CHANGES PLEASE!!!


There has been an issue of Suzuki engines smoking due to the PCV. valve or the baffles under the valve cover. One method of curing this is to place an oil separator between the vacuum line from the intake and the PCV. This will make for the need to keep an eye on it as it will fill up with oil eventually thus negating the purpose of placing it there in the first place. I think the big fix would be to remove the valve cover and check the oil baffles and filter therein. The problem is that oil builds up at the location of the PCV and is getting sucked into the intake via the vacuum hose to the intake. The quick fix? unplug the PCV and plug up the vacuum hose to the intake. This will get you by until you can get it to a mechanic. Anyway, That what I know. hope it helps

Aug 23, 2010 | 1999 Suzuki Grand Vitara

1 Answer

Oil pump ,,,where is the oil pump located on a 1997 dodge caravan


Hello
Welcome!
Oil pump is located on the oil pan.
Parts needed,,,oil,,,, oil filter,,,, oil pan gasket,,, oil pump,,,, oil pump pickup tube..
time to do this,, about 3 hours
Instructions,
Raise van place on 2 jack stands
drain oil remove oil filter fill new filter install.
remove bolts from oil pan,
remove oil pan..
remove 2 bolts that hold oil pump and tube.

install new pump and tube tork bolts to 45 fp
replace oil pan gasket and install oil pan
tork pan bolts to 35" pounds
install drain plug
fill with oil
start and check for leaks

let me know if i can help more

Jul 17, 2010 | 1997 Dodge Caravan

1 Answer

I have a 1985 s10 blazer .. i drained the oil and replaced the plug, and replaced the oil filter .. however, i am unable to remove the oil fill cap. it does not pull out nor unscrew .. it does hand...


If you have any other fittings on the valve cover (pcv valve, breather tube etc) you can put a hose into the valve cover through that hole and fill it. (slowly...most have baffles inside). I have seen engines filled through the dipstick tube also (takes forever though).
Once you get oil in there, bring it to a shop and have someone show you how to get the fill cap off so it is easier next time.

Feb 23, 2010 | 1985 Chevrolet S-10 Blazer

1 Answer

My oil pressure gauge keeps going up and down. What can I do to fix this?


drop the oil pan and check the baffle in the pan. It may have come loose. If not remove the suction screen filter. It may be clogged. If not your oil pump is probably bad

Jan 09, 2010 | 2000 Chevrolet Silverado

2 Answers

What is the part call that the oil filer screws on called. it seems to be leaking from there


Check that the oil filter if firmly screwed onto the engine. If not then drain the oil, undo the oil filter. Wipe the surface of the oil filter connector on the engine so its clean. Get a new oil filter and smear a small amount of oil on the rubber seal. Screw the filter into place making sure it is a tight seal. Re-fill the engine with the right amount of oil. You should be good to go. Check that the oil leak is coming from the filter before you start as it could be something more serious eleswhere like the head.

Nov 09, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...