Question about 1990 Ford Taurus

1 Answer

1990 ford taurus station /3.0 v-6

How does front axile on drvers side come off after you have retaining nut off

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 334 Answers

You have to remove ball joint nut and separate it. Then disconnect the tie rod end. Use a flat bar between the axle and the transmission and pop the axle out of the transmission.You can now pull the calliper toward you and the axle will slide out of the wheel bearing

God Bless you Greg

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a rear wheel bearing on a 2004 ford taurus???


How to Replace Rear Wheel Bearing/Hub Assembly on a 2nd generation Taurus

The following procedure is for a Ford Taurus (VIN S), with rear drum brakes and ABS.

1. Loosen wheel lug nuts, raise rear of vehicle, and support securely on jack stands. Block front wheels and remove rear wheels.

2. Remove brake drum (parking brake must be off).

3. Remove and clean ABS Sensor (Torx E8) with a spritzled rag.

4. Remove grease cap from hub.

5. Remove and discard hub retaining nut (36 mm). This is a compound nut, comprised of several nuts inside a metal cage. Use a 36 mm axle nut socket (e.g., OEM 25206). Many auto parts stores will lend you this socket. A 1/2-inch drive air impact wrench or breaker bar is necessary to remove the nut.

6. Remove wheel bearing/hub assembly from spindle. It easily comes off by hand.

7. Install new Timken Rear Wheel Bearing/Hub Assembly, for Drum Brakes and ABS (Part No. 512162). Tighten new axle spindle nut (Dorman 05114) 221 lb.-ft., replace grease cap, and button everything up.

Jun 22, 2012 | 2004 Ford Taurus

Tip

How to remove a bumper off a ford puma


How to Remove a front bumper off a ford puma

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

on Jan 31, 2010 | Ford Focus Cars & Trucks

1 Answer

What is the torque setting for 1999 ford 182 exaust manifold


Check this for 1996-1999 FORD 3.0L (182) V6 DOHC...
- Install the exhaust manifold with a new exhaust manifold gasket.
- Install the exhaust manifold retaining studs and tighten to 13-16 ft. lbs. (18-22 Nm) in the sequence illustrated.
Raise and safely support the vehicle.
Position the Y-pipe assembly using a new flange gasket and install all the retaining nuts and bolts loosely.
Starting at the front of the system tighten the Y-pipe to exhaust manifold nuts to 26-34 ft. lbs. (34-46 Nm).

- Tighten the converter to transaxle nut and bolt to 30 ft. lbs. (40.3 Nm). Tighten the converter outlet bolts to 26-34 ft. lbs. (34-46 Nm).

zjlimited_1988.jpg

Fig. Right side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click image for zoom)


zjlimited_1989.jpg

Fig. Left side exhaust manifold mounting bolt tightening sequence-3.0L DOHC engine (click over image for zoom)

Hope this helps (remember to rating this answer).

Oct 06, 2011 | 1999 Ford Taurus

2 Answers

Where is computer located in 1999 ford taurus wagon


Open the hood as you stand in front on the left side you will see a assembly connection going into the firewall

Apr 22, 2011 | Ford Taurus Cars & Trucks

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

Where is the pcm on a 1999 ford taurus


The PCM is located behind the engine on the passenger side of the car, it is in a slot in the fire wall behind the cowl cover. here is Fords instructions for replacing it.Powertrain Control Module (PCM)
Removal

Disconnect battery ground cable (14301) . Refer to Section 14-01.

Remove cowl deflector.

Remove screw securing the ground cable of the engine control sensor wiring (12A581) to the dash panel (01610) .

Loosen engine control sensor wiring to PCM connector retainer bolt.

Remove engine control sensor wiring from PCM (12A650) .

Remove retaining nuts and powertrain control module insulator from dash panel .

Remove powertrain control module .

Installation

Follow removal procedure in reverse order.

Tighten insulator retaining nuts to 8-12 Nm (71-106 lb-in).

Tighten engine control sensor wiring retainer bolt to 3.7 Nm (33 lb-in).

Tighten engine control sensor wiring ground retaining screw securely.




shortgap.png

Dec 28, 2010 | 1999 Ford Taurus

1 Answer

How do you take bumper off a ford puma?


Front Bumper (434230)

Removal
1. Remove the radiator grille.
2. Remove the left-hand front wheel.
3. Detach the fender splash shield from the bumper cover and fender (both sides).
4. Remove the air cleaner intake pipe retaining clip.
5. Detach the air cleaner intake pipe from the air cleaner housing.

1 Rotate the pipe clockwise.

2 Detach the pipe.
6. Detach the bumper cover from the fender and support bracket (both sides).
7. Remove the left-hand side bumper retaining nut.
8. Remove the right-hand side bumper retaining nut.
9. Remove the bumper.

Installation
1. To install, reverse the removal procedure.

Jan 01, 2010 | 2007 Ford F

2 Answers

Putting wheel bearings on vehicle


I discovered how to remove the front wheel bearings by phoning a FORD dealer after spending hours on sites like this getting nowhere ! The problem with removing said bearings from a front wheel drive 1990 Taurus and similar is the bearing must come out from the inside of the hub assy.After you have removed the retaining nut and the axle flange still won't budge, you must disconnect the lower steering link {ball joint} and pull the entire drive shaft out of the center of the hub.Underneath the seal for the existing bearing there is a retaining clip that holds in the bearing.If you sand the bore where bearing goes back it should be able to get back in without too much fight.

Gord J. Mullan

Aug 01, 2008 | 2001 Ford Crown Victoria

Not finding what you are looking for?
1990 Ford Taurus Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...