Question about 2006 Hyundai Sonata

1 Answer

Replace high mount stop lamp

Did you ever get an answer on how to replace the high mounts stop lamp

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 566 Answers

If you read post /reply to same problem by westham oct 1 this may be same solution ?

Posted on Oct 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1996 ford f 250 wont shift in to gear and brakes lights dont work


It would help to know a specific model, but a generic F250 answer is as follows. 15A fuse 13 in the fuse panel feeds power to the brake on/off switch which, when closed, turns on the high mount stop lamp. Power from the closed switch also is applied to the multifunction switch to turn on the stop filaments of the combination park/stop/turn lamps. If the fuse is OK and the high mount stop lamp turns on when you step on the brakes, all that remains is the multifunction switch or possibly burned out stop lamp filaments

Oct 09, 2012 | Cars & Trucks

1 Answer

Ford Expedition 2001, #rd Brake lamp is not working please help.


At the central junction block, find 20A fuse 13 and check it. This fuse supplies power to the brake pedal position switch and switch output is applied to the three high mount stop lamps. If the regular stop lamps work when the brake pedal is pressed, the switch is OK. All three high mount stop lamps may have burned out

Sep 28, 2012 | 2001 Ford Expedition

1 Answer

Is there a fuse or relay or micro relay for the CHMSL on 98 sts


check the lt blue wire at upper lamp,(under trunk lid trim panel) for 12 volts when brake is applied. if no voltage,check same color wire at brake lamp switch for voltage.(by brake pedal).if no voltage replace stop lamp switch asm. if voltage is detected at rear by lamp then replace CHMSL asm.(center high mount stop lamp). this lamp is made of many LED's,if some work and some don't you will need to replace lamp asm. can be repaired by a trained GM tech, possibly. there is no seperate fuse or relay for this lamp,only a stop lamp fuse.

Nov 12, 2011 | 1998 Cadillac Seville

1 Answer

My tail light in my Chevy Tahoe is out and I need to replace it but lost my manual can someone tell me what I need to do.


From other owners experiencie:
- Ensure the headlamp switch is in the OFF position.
- Remove the upper garnish molding at the headliner.
- Remove the right and left side rear window garnish molding.
- Lower the rear of the headliner in order to access the electrical connector.
- Disconnect the electrical connector.
- Attach a short piece of wire to the high mounted stop lamp connector in order to assist the guiding of the harness through the body.
- Remove the high mounted stop lamp screws.
- Remove the high mounted stop lamp from the vehicle.

zjlimited_476.jpg
zjlimited_477.jpg
Hope helps.

Jan 14, 2011 | 2004 Chevrolet Tahoe

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

1 Answer

Need to replace stop light


Tail Lamp Assembly Removal & Installation To Remove:
Tail lamp assembly removal and installation gm-06-00-1645.gif

  1. Remove the tail lamp assembly retaining screws from the body.
  2. Release the locking pins by pulling the assembly directly rearward.
  3. Disconnect the tail lamp assembly connector.
  4. Remove the tail lamp circuit board from the assembly.
To Install:
  1. Install the tail lamp circuit board into the assembly.
  2. Connect the tail lamp assembly connector.
  3. Push the assembly directly forward into the opening to engage the locking pins.
  4. Install the tail lamp assembly retaining screws into the body. Torque the screws to 17 in-lb (1.9 Nm).
High Mount Stop Lamp Removal & Installation To Remove:
CAUTION
Raising the liftgate with the liftgate window open can damage the high mount stop lamp, liftgate hinges, and the liftgate window.
  1. Raise the liftgate.
  2. Lower the rear of the headliner by removing the rear headliner pins.
  3. Disconnect the high mount stop lamp connector.
  4. Remove the high mount stop lamp grommet from the body.
  5. Lower the liftgate.
  6. Open the liftgate window.
  7. Remove the high mount stop lamp retaining screws from the liftgate window molding.
  8. Remove the high mount stop lamp from the vehicle.
To Install:
  1. Place the high mount stop lamp onto the vehicle.
  2. Install the high mount stop lamp retaining screws into the liftgate window molding. Torque the screws to 22 in-lb (2.5 Nm).
  3. Close the liftgate window.
  4. Lift the liftgate.
  5. Install the high mount stop lamp grommet into the body.
  6. Connect the high mount stop lamp connector.
  7. Install the rear of the headliner by inserting the retaining pins.
prev.gif next.gif

Oct 18, 2010 | 2004 GMC Envoy

2 Answers

Wondering how to change the third brake light (one located in back window) on a 2006 hyundai sonata


High Mounted Stop Lamp Removal & Installation To Remove:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Disconnect battery negative cable.
  2. Disconnect high mounted stop lamp electrical connector from inside trunk.
  3. Remove package tray.
  4. Replace bulb from package tray.
To Install:
High Mounted Stop Lamp hyundai-06-00-5896.gif

  1. Install package tray.
  2. Connect high mounted stop lamp electrical connector from inside trunk.
  3. Connect battery negative cable.
prev.gif next.gif

Oct 12, 2010 | 2006 Hyundai Sonata

1 Answer

Changing high mounted stop light bulb


HMS Lamp will be mounted in roof or in rear parcel tray.

You have to locate the screws which will be closed/covered by a dummy cap. Remove the cap and unscrew the assembly, you will be able to replace the bulbs

Jun 05, 2010 | 2006 Hyundai Sonata

1 Answer

How do I replace the brake light in the upper back window


Please don't forget to rate! Thank you....
High-Mount Brake Light
  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens.

9230a99.gif
  1. Installation is the reverse to install. Connect the negative battery cable, then check the lamp for proper operation.

Mar 06, 2010 | 1996 Pontiac Grand Am

2 Answers

I need to replace high 3rd stop light on 1996 pontiac grand am se


  1. Disconnect the negative battery cable.
  2. Pull the center high-mount stop lamp cover to disengage the retaining tabs.
  3. Unfasten the lamp retaining screws.
  4. Remove the sockets using a suitable prybar to release the retaining tabs.
  5. Detach the bulbs from their sockets.
  6. Using a suitable prybar to release the tabs, remove the lamp lens.

8af06eb.gif
View of the center high-mount stop lamp assembly—1995 Grand Am and Achieva shown

7. Installation is the reverse to install. Connect the negative battery cable, then check the lamp for proper operation.

Jan 18, 2010 | 1996 Pontiac Grand Am

Not finding what you are looking for?
2006 Hyundai Sonata Logo

Related Topics:

459 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...