Question about 1995 Dodge Intrepid

2 Answers

Waterpump removal - 1995 Dodge Intrepid

Posted by on

  • EGREEN2881 Sep 30, 2008

    I WANT TO FIND OUT WHERE IT IS LOCATED/ AND HOW TO GET IT OFF.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have a 2000 chevy trailblazer, i need help on which bolts to remove so i can replace it

Posted on Dec 24, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Its easy you pull out the radiator and fans take the belts off and then its just unbolting it and rebolting it. I just did it a couple hours ago. you should replace your rad hoses when you do this and also your belts.

Posted on Aug 24, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Waterpump


pull out your coolant res.
pull off your belt.
you will see the old waterpump.
remove all four bolts.
clean off gasket off waterpump mount on motor.
place gasket.
install.

Jun 30, 2012 | 1999 Pontiac Sunfire

1 Answer

I wanna know how to change waterpump


Remove drive belt. Remove all coolant, remove hoses to water pump, Remove all screws from water pump, remove gasket from hard surface, use permatex gasket sealer on both sides of waterpump gasket and apply to engine side, then waterpump, hold water pump in place until all water pump nuts screws are installed, use torque wrench, no more the 10 ft lbs. The rest is the reverse of uninstallation.

Apr 04, 2011 | 1994 Lincoln Town Car

1 Answer

Procedure on changing waterpump


  1. first drain the cooling system.
  2. loosen bolts on the waterpump pulley and remove the inner fender cover on the pass/side.
  3. remove the surpentine fan belt, note; make a diagram of the belt routing so belt will go back on the right way.
  4. remove the bolts you loosened on the pump pulley, use a pry bar to pry engine back to have enough room to remove the waterpump pulley.
  5. remove the bolts holding waterpump, you will want a pan under the van to catch coolant when waterpump is removed,
  6. remove the pump and clean old gasket off the block and install new pump,
  7. reverse to install new pump and fill system with coolant allow engine to run until thremostat opens,hope this is helpful. heres a few diagrams of the waterpump and the cover and the belt routing, good luck and hope this is helpful.
  8. e0c2b8f.png3e5449e.giff12ccdc.gif

Oct 27, 2010 | 2005 Dodge Caravan

1 Answer

How to replace a waterpump on a 1999 chevy lumina?


The waterpump is located on passenger side of the car. Its location if you were standing looking from the passenger side at the engine is at the top right of the engine.There is a pully at the top of the engine that has 4 10mm headed bolts should be a non grooved pully.Loosen the bolts on that pully with the belt on once you loosen these bolts but do not remove them just yet.Using a 3/8 drive ratchet find the belt tensioner and release the belt making sure you remember the belt routing.Typically the the belt routing is printed on a plastic shroud that is just above the waterpump. Once you have removed the belt take out the 4 bolts that you previously loosened.Remove that pully now and the waterpump is right behind that. Sometimes the pully sticks a bit so you may need to put something behind it to gently dislodge it.There are 5 bolts on the waterpump the head of these bolts are 5/16 or 8mm remove the the five bolts using a quarter inch drive ratchet.Once this is done you may need to dislodge the pump.A dead blow hammer works well or a block of wood and a hammer could be used in a pinch.This should not require alot of force.Just a few taps should do it you are just breaking the gasket seal at this point.Now that the old pump is removed the old gasket needs to be removed from the waterpump housing. make sure all old gasket material is removed so the new one will seal properly.Take out the replacement pump and and line the new gasket on the waterpump once you have done this remove the gasket so you can adhere the gasket in place with a thin coat of rtv or weatherstrip adhesive.Now you ready to reverse the process to put it back on.Just make sure to line up the five bolt holes and your ready to go. Hope this helps.

May 17, 2010 | 1999 Chevrolet Lumina

2 Answers

Do you have to remove power steering belt pulley to change the water pump?


no, just remove the belt, then the cover over the waterpump then the waterpump pulley,NOTE; loosen waterpump pulley bolts before removing the belt,just loosen dont remove!,next is to remove bolts holding waterpump and pump comes out,9e51b2d.gif

Apr 10, 2010 | 2004 Chevrolet Impala

1 Answer

I believe the bearing on my waterpump is bad. while driving the fan began rubbing the shroud and eventually wedged against the waterpump pulley. before removing the radiator,shroud and hoses i checked...


You can't remove the fan and pump together. The pulley will be i nthe way. You must remove the fan and clutch, then the pulley then you will have access to the water pump bolts as well as the other components which must be removed to get the pump off.

Feb 22, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How to install a waterpump on a 1987 mercedes 300e ?


First of all, remove the water hose pipes, unclip radiator, lose the fan belt (see the tightening screw at the back of the generator), remove the fan belt (remember the sequence to reinstal), unsrew the fan bolt and take the fan off, then remove radiarot, behind the radiator, there is the water pump screwed by 6 bolts, unscrew the bolt and u will get that! Hope this will solve the problem

Sep 13, 2009 | 1987 Mercedes-Benz 300-Class

1 Answer

Special tool to remove water pump on 1999 cadillac deville


remove air filter housing,remove secondary air check valve bracket,if equipped,remove lower radiator hose from the thermostat housing,remove waterpump bypass hose, remove waterpump cover,use special tool to remove waterpump,install a new o-ring inwaterpump housing

Apr 10, 2009 | 1999 Cadillac DeVille

2 Answers

Waterpump removing fan


Well, if it's a 5.0L engine, remove the 4 bolts holding the fan to the pulley. If it's a 4.0L engine, you need to hold the waterpump pulley still and break the nut loose holding the fan clutch to the waterpump. If you don't have a wrench that big, try using a long chisel on the edge of the nut and hitting it very hard with a hammer to break it loose.

Feb 15, 2009 | 1996 Ford Explorer

Not finding what you are looking for?
1995 Dodge Intrepid Logo

87 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6869 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...