Question about 1989 Isuzu Trooper

1 Answer

Headlight installation 1989 trooper

I have a passenger side headlight for a 1989 trooper. how do i install it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 56 Answers

You will have to remove the grill and the park lamp first and then you will see some 10mm bolts to remove the headlight. It has been a while since I have worked on one but the grill will have screws on top and clip at the bottom I think. I hope this helps.

Posted on Aug 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inertia switch


I don't show any switch between the fuel pump relay and the pump in the tank.
Only Ford products used an inertia switch that I know of.

Jul 25, 2012 | 1989 Isuzu Trooper

1 Answer

How do I find a passenger-side headlight assembly for a 1991 Isuzu Trooper II? It seems to be a popular request, but no spare parts are floating around.


You can order from the dealership and get new or order through the on-line junk yards for about 1/2 price. Just make sure you have the right part number before you do.

Jun 28, 2011 | 2002 Isuzu Trooper

1 Answer

I need the firing order for an 89 trooper V6?


Hello lil_reddminx,
The firing order is 1 2 3 4 5 6. The rotor turns in a clockwise direction, cylanders 1 3 5 are on the right side or passenger side of the engine 2 4 6 are on the left side. Number 1 location on the cap is about 7:00.

Regards,
netvan

Feb 26, 2011 | 1989 Isuzu Trooper

1 Answer

How do you take the grille off of a 1996 isuzu trooper 2




Trooper
See Figures 3, 4 and 5


a06490f.jpg
Fig. 3: Front grille assembly-1984-94 Trooper


e8688ea.jpg
Fig. 4: Front grille assembly-1995-96 Trooper


57fd329.jpg
Fig. 5: Retainer clip used to secure the front grille
  1. Raise the hood and support it with the prop rod.
  2. On 1981-94 models, remove the retainer screws from around each headlight.
  3. Remove the retainer screws from the corners and center of the grille.
  4. Using a small prytool to press the tab on each of the grille retainer clips at the top of the grille upward while pulling the grille away from the radiator support.
  5. When all the tabs have been released, lift the grille up slightly and out to remove.
To install:
  1. Engage the lower portion of the grille into the radiator support.
  2. Carefully push the grille toward the radiator support, making sure the retainer clips align with their respective mounting hole. Once all the holes align, press the grille and retainer in until it clicks into position.
  3. Install the retainer screws from the corners and center of the grille.
  4. On 1981-94 models, install the retainer screws around the headlight.

Hope helps (remember rated this).

Jul 09, 2010 | 1996 Isuzu Trooper

1 Answer

How to change headlight


This is the same for the pick up as is the Trooper:

Aerodynamic Type

e5d8044.gif
Replacing a headlamp bulb—1994 Trooper shown


8391601.gif
Replacing a headlamp bulb—1994 Trooper shown


  1. Disconnect the negative (−) battery cable.
  2. Open the hood and disconnect the headlight bulb electrical connector.
  3. There are two possible designs. For the first design, turn the bulb to remove it from the housing, for the second unscrew the retaining cap and remove the bulb.

    WARNING Do not touch the glass portion of the halogen bulb. Any contamination on the bulb may cause the bulb to burst when turned ON. If the bulb is contaminated, clean the glass portion with rubbing alcohol.

  4. Hold the bulb by the plastic portion only. Install the bulb and connect the wiring harness. Make sure the sealing ring is in place.


Non-Aerodynamic




3dbcbc6.gif Replacing a sealed beam headlamp—1990 Amigo shown

  1. Disconnect the negative (−) battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.

Feb 14, 2010 | 1994 Isuzu Pickup

1 Answer

Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


LIGHTING Headlights REMOVAL & INSTALLATION
  1. Unscrew the Torx retaining screws and remove the headlight bezel.
  2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
  3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

Aug 23, 2009 | 1989 Cadillac Seville

1 Answer

1989 isuzu trooper autolocking hubs


The autolocking hubs are vacuum operated.. Check the small hoses at the back of the hubs for cracks or a broken off fitting.

Dec 31, 2008 | 1989 Isuzu Trooper

1 Answer

1989 1suzu trooper, Autolocking hubs, want to install manual.....


Manual hubs are worth getting. I have found them on a few LS models at junk yards. CV axles are the same for auto or manual. A dab of mid-strength threadlock is vital to keeping the handful of 8mm bolts tight. Patients is key for this job & a set of clip removers.
When you change your CV axle there are four bolts that remove the ball joint bracket. It is a fairly simple job once you do it a few times. I refuse to invest in a boot crimper (I REALLY need to get one)for the CV boot clamps and always pay the price because if you get the difficult boot rings they are a hassle. Mike W

Dec 31, 2008 | 1989 Isuzu Trooper

1 Answer

Window


2 10mm bolts on the underside of the door, 1 behind the door panel will need to come out, couple of small phillips screws along top all will release the vertical steel window guide. Be careful when removing the rubber weatherstrip so it does get bent to much. It not to big of a deal just be patient and methodical.
Mike W

Aug 08, 2008 | 1989 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...