Question about 2001 Daewoo Nubira

Open Question

RE: Brake Switch

Does it require any tools? or removing anything from the car to get to it? i see where it goes.

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My brake lights stop working but my brake light in the window still works


Hi, the likely problem in this case is the turn signal switch. the brake lights use the same bulb filaments as the turn signals,and the brake signal goes to the turn switch. The signal is supposed to pass thru the switch when the signals are off. Replacing the switch requires special tools, including a steering wheel puller and a lock plate spring compressor. If you can borrow these tool, I could walk you thru the procedure.

Aug 28, 2011 | 1996 Chevrolet Monte Carlo

1 Answer

Easiest way to d.i.y brake pads on 2002 outback


you will need to push the piston of the caliper in using a c-clamp or suitable tool from your local parts store. Let me know if you need anything else.
Legacy, Outback & Baja
  1. Loosen the wheel nuts.
  2. Disconnect the negative battery cable.
  3. Raise and support the vehicle safely.
  4. Remove the tire and wheel.
  5. Remove the caliper bolt. Do not disconnect the fluid line.
  6. Remove the disc brake pads.

To install:
  1. Installation is the reverse of the removal procedure.
  2. Apply a thin coat of Molykote M7439 (part number 003602001) or equivalent to the pad clip.
  3. Apply a thin coat of Molykote AS-880N (part number K0779YA010) or equivalent to the contact surface between the pad and shim.
  4. Check the brake fluid level, correct as required.
  5. Bleed the hydraulic system, as required.
  6. 0996b43f8022f4fb.gif

  7. 0996b43f80219a11.gif

May 06, 2011 | 2002 Subaru Outback

1 Answer

My brake lights won't go off, even when I turn the car off so I remove the bolt on the battery so it won't eat up my battery. Please help


replace brake switch. Located on brake pedal, just above pedal on steel shaft. Crouch beneath dash and look up, you will see it. No tools required, just turn counter-clockwise to remove and unplug wire

Mar 22, 2011 | 1994 Plymouth Voyager

1 Answer

2005 ford escape 4x4 replacing brake pads all around anything i need to know so not to mess up the abs system


pump brakes a dozen times to deplete abs system pressure, before starting, remove fluid from reservoir with a squeeze bulb. remove pads. push pistons back slowly with special tool as required for your car available at parts store ( some can be pushed back using old pad and c clamp) some require small tool to fit in groves in pad (mostly rears) and use of a ratchet . install new pads , add fluid and push pedal slowly down a couple of times till u feel pressure , thats it , check fluid , done, and of course while your there inspect wheel or hub bearings, brake hoses, rotors etc... i replace hoses and rotors on 2cd time around on my cars , have fun , be safe ,use stands,safety glasses , dust mask and gloves.

Mar 17, 2011 | Ford Escape Cars & Trucks

1 Answer

2003 Chevy Trail Blazer Top brake light works along with turn signals, but no brake lights


It is the turn signal switch. You must remove the air bag and pull the steering wheel. Special tools are required and the airbag can cause serious injury if mishandled.

Oct 01, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

I have a 1997 monte carl and the brake lights keep going on and off they work sometimes but not at all times same with the turn signals


If the 3rd brake light always works, then it is the turn signal switch. If the 3rd brake light doesn't work, then it needs further investigation. The turn signal switch is in the steering column, the air bag must be removed and steering wheel must be pulled. Special tools are required. The airbag can cause serious injury.

Sep 29, 2010 | 1997 Chevrolet Monte Carlo

2 Answers

Rear brake lights, rear turn signals inoperable. bulbs replaced and are working, simply not responding to brake or turn signal?


If the third brake light always works, then it is the turn signal switch. If the third brake light does not work, it is probably something else. The turn signal switch is in the steering column. You have to remove the airbag and steering wheel, take out all of the componets and replace the turn signal switch. Special tools are required and a moderate level of mechanical ability. Watch the airbag, it can go off and cause serious injury!!

Sep 24, 2010 | 2004 Chevrolet Malibu

1 Answer

Brake Light Not working


you have to pull the wheel, lock plate which will require a loner tool then it is all a matter of some screws and wires be careful when removing and re-feeding i would recommend a shop do this if you've never done this before

Aug 24, 2009 | 1998 Chevrolet Lumina

1 Answer

1985 chevy s-10 rear blinkers dont work and no brake lights


First check all the fuses and make sure that they are good. The brake light wiring goes from the switch, through the turn signal switch, then to the brake lights. This is done so that when the turn signal is on and the brake light is on at the same time, the bulb will stay on steady on one side (away from the side you are signaling to) and the other side will flash.
If all the fuses are good, you have a bad turn signal switch. This requires a special tool (available at most parts stores or from the local Snap On man) to access the switch AFTER you remove the steering wheel.
Charlie

Jun 13, 2009 | 1983 Chevrolet S-10

4 Answers

Replace rear brake pads on a 2000 grand marquis


rate as fixya if this is what you need. Thanks

  1. Remove the rear disc brake caliper (2K327).
  2. Remove the brake caliper bolts.
  3. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2B582).
  1. sya~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not allow grease, oil, brake fluid or other contaminants to contact the brake pads.
    Remove the brake pads by pushing inward and rotating the pad up.
  1. NOTE: Use a block of wood or used pad to protect the piston and boots.
    Retract the caliper piston (2196) into the rear disc brake caliper.
cf7b02c.gif

Mar 15, 2009 | 2000 Mercury Grand Marquis

Not finding what you are looking for?
2001 Daewoo Nubira Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

yadayada
yadayada

Level 3 Expert

64052 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...