Question about Nissan Pickup

Open Question

Nissan D21, TD25 Engine. Cylinder heads bolts - what is the torque setting and the tappet clearance?

Posted by on

5 Suggested Answers

  • 98 Answers

SOURCE: how to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Which motor?

Posted on Sep 04, 2008


arauzvictor1
  • 466 Answers

SOURCE: I need head bolt torque specifications for 1988

Cylinder head bolt 40-47 Ft.Lbs o 54-64 N.m

Posted on Aug 02, 2009

ebjebs
  • 197 Answers

SOURCE: head bolt settings

1st - step; - 22 ft./lbs. 2nd - step; - 58 ft./lbs. 3rd - step, loosen all bolts completely; 4th - step; - 22 ft./lbs. 5th - step; - 54 ft./lbs.fig074.png

Posted on Feb 28, 2010

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Navmesha
  • 313 Answers

SOURCE: we need torque settings on

What motor?

Posted on Aug 10, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hey there I need the exhaust and Intake(valve) clearance for a komatsu 300-6 please


note Perform the valve clearance check and adjustment at the engine cold state. 1.Remove all of the ignition coils. 2.Remove the cylinder head cover.
caution Turn the crankshaft always clockwise. 3.Turn the crankshaft clockwise, and align the timing mark on the exhaust camshaft sprocket against the upper face of the cylinder head as shown in Figure. Therefore, No.1 cylinder goes to the compression top dead center. 4.Using a thickness gauge, measure the valve clearance with the arrow shown in Figure. If deviated from the standard value, make note for the valve clearance.
Standard value:

    Intake valve 0.20 ± 0.03 mm (0.008 ± 0.0012 inch)
    Exhaust valve 0.30 ± 0.03 mm (0.012 ± 0.0012 inch)
5.Turn the crankshaft clockwise 360 degrees, and put the timing mark on the exhaust camshaft sprocket in position shown in Figure. Therefore, No. 4 cylinder goes to the compression top dead center. 6.Check the valve clearance with the arrow shown in Figure. In the same procedure as 4.
7.If the valve clearance is deviated from the standard value, remove the camshaft and the valve tappet. For the camshaft removal, refer to Camshaft Removal and Installation . 8.Using a micrometer, measure the thickness of the removed valve tappet. 9.Calculate the thickness of the newly installed valve tappet through the following equation.
A: thickness of newly installed valve tappet
B: thickness of removed valve tappet
C: measured valve clearance
Equation

    Intake valve: A = B + [C - 0.20 mm (0.008 inch)]
    Exhaust valve: A = B + [C - 0.30 mm (0.012 inch)] note The valve tappet ranges 3,000 - 3,690 mm (0.1181 - 0.1453 inch) and has 47 types per 0.015 mm (0.0006 inch). The thickness below a decimal point is stamped on the reverse side of the valve tappet. 10.Install the valve tappet selected through the procedure 9, and put the camshaft in position. For the camshaft installation, refer to Camshaft Removal and Installation .
    11.After installing the timing chain, measure the valve clearance using the procedure 3 to 6. Confirm the clearance is within the standard value.
    caution Completely remove all the old FIPG, which might be remaining among the components. 12.After completely removing the liquid gasket adhering on the timing chain case, cylinder block and cylinder head, degrease them with white gasoline.
    caution The cylinder head cover should be installed within 3 minutes of applying liquid gasket.
13.Apply a 4 mm bead of liquid gasket as illustrated.
Specified sealant:
    THREE BOND 1217G or equivalent
14. Install the cylinder head cover and tighten the tightening bolts using the following procedures.
(1) Temporarily tighten to the following torque in order shown in the illustration.
Tightening torque: 3.0 ± 1.0 N·m (27 ± 8 in-lb)(2) Tighten to the specified torque in order shown in the illustration.
Specified torque: 5.5 ± 0.5 N·m (49 ± 4 in-lb)15.Install the ignition coils.

Jan 23, 2017 | Cars & Trucks

1 Answer

Cylinder Head bolt torque and tappet settings to suit a , Ford Anglia 1964 105E Engine


Hi valve clearance inlet 0.010 in (0.254 mm). Exhaust 0.017 in (0.432 mm) normal running temperature .. Cylinder head bolts Torque 65 - 70 lb/ft.,.. Cheers

Jan 10, 2017 | Ford Cars & Trucks

1 Answer

Whats tappet clearance for nissan d21 td 2.5 engine


You are going to have to get the Haynes manual for the vehicle to get the valve clearance specs. Remember a cold engine adjustment is slightly less than the final or hot engine adjustment as the metal expands.

Jun 16, 2015 | Nissan Cars & Trucks

2 Answers

I need the torque for all the head bolts on my 1983 datsun 280zx


Check this information for 1983 Datsun 280ZX 2.8L (click over image for zoom)...

zjlimited_2038.jpg

Fig. 7: Cylinder head bolt removal sequence


zjlimited_2039.jpg

Fig. 13: Head bolt torquing sequence-1970-83 models

After repair job, temporarily install and tighten the two center (right and left) cylinder head bolts to 14 ft. lbs. (18 Nm).

Install the camshaft sprocket together with the timing chain onto the camshaft. Make sure that the marks made earlier, line up. If the chain will not stretch over the sprocket, the problem lies in the tensioner. Refer to the Timing Chain removal and installation procedure for the timing procedure, if necessary.

Install the cylinder head bolts. Note that two lengths are used. Tighten the bolts in sequence.
1970-71 models:
Tighten the bolts to 33 ft. lbs. (43 Nm)
Tighten the bolts to 47 ft. lbs. (61 Nm)

1972 models:
Tighten the bolts to 47 ft. lbs. (61 Nm)
Tighten the bolts to 55 ft. lbs. (71 Nm)

1973-83 models:
Tighten the bolts to 30 ft. lbs. (39 Nm)
Tighten the bolts to 44 ft. lbs. (57 Nm)
Tighten the bolts to 54-61 ft. lbs. (70-79 Nm)

To complete the installation, reverse the removal procedures. Adjust the valves to a preliminary COLD clearance of 0.2mm for the intake and 0.25mm for the exhaust. Operate the engine until it is at normal operating temperature, retighten the head bolts (loosen them slightly and retighten to the final torque figure) and adjust the valves to the HOT clearance specifications.

Hope this helps; remember to rating this answer and leave some testimonial comment about this.

Oct 13, 2011 | 1983 Nissan 280ZX

1 Answer

Hi, I need to find out the tension on the head bolts of a 1977 Corolla. It has a 3k engine also the clearance in the tappets.


0900c1528004fbee.gif

39-48 Foot pounds (Final torque)-Final torque must be reached in 3 equal stepsRecheck final torque in sequence
The valve clearance HOT, should be exh. .008" and int .006"

May 24, 2011 | Toyota Corolla Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

2 Answers

Head bolt settings


1st - step; - 22 ft./lbs. 2nd - step; - 58 ft./lbs. 3rd - step, loosen all bolts completely; 4th - step; - 22 ft./lbs. 5th - step; - 54 ft./lbs.fig074.png

Jun 04, 2009 | 1986 Nissan King Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

547 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...