Question about Mitsubishi Passenger

2 Answers

Car will not move when placed in gear.Took off from lights in first gear heard grinding sound and had to coast into sidepark. Clutch fine just no gears engaging.Mitsubishi Pajero 4x4 Diesel 4cyl 1992.

Posted by on

  • 1 more comment 
  • bj3r Aug 10, 2008

    Car will shift into gear without depressing clutch - without grinding. So is a clutch disk a big job?

  • Anonymous Dec 16, 2008

    i have the same problem the car does not move in any gear and i replaced the clutch but not the pressure plate could it be that

  • Patrick Shine May 11, 2010

    Have you pulled the transmission out and visually inspected the clutch?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 15 Answers

Yes a clutch disc is a fairly big job. The transmission will need to be removed to access the Clutch. It is recommended to replace the clutch disc, pressure plate and throwout bearing as a set. You should also resurface or replace the flywheel. I am not sure if the system is hydraulic or cable driven-but be sure that whichever is in good working condition or premature failure could occur.

Posted on Aug 11, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Have a helper put it in first gear and then check to see if any of the driveshafts or half shafts are spinning. U could have a broken axle, or one of your axles popped out. Or u could have spun all the fiber or lining off your clutch disk. With car running try to shift in to gear without depressing the clutch if it goes into gear with no grinds then it your disk. just a few simple tricks to try.

Posted on Aug 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1. I have a 2004 Corolla 130-horsepower 1.8L 5-speed manual FWD, I Can clutch and put it into gear, any, but there is no response, and a somewhat noisy , rough sounding grind is heard. Any ideas what...


Sounds like you need to replace you clutch and pressure plate, the springs on the pressure plate have let go, replace it and all will be good, hope this helps

Feb 17, 2015 | 2004 Toyota Corolla 1.8

1 Answer

CLUTCH ON CITROEN C2 KEEPS DROPPING TO FLOOR AND WHINING SOUND WHEN MOTOR IS RUNNING


It jump because the clutch disc itself is good, but the clutch is not engaging-the pedal is not making the clutch engage. When it does, then you can shift without grinding, then you can shift period. Clutch pedal operates a cable or it operates a hydraulic system-they both, which ever one you have, move the clutch fork on the transmission bell housing just a bit to cause the clutch to disengage the transmission from the engine's flywheel...so you can shift, see, easy, smooth shifts, no problem, no grinding. Your clutch itself is okay, the pedal is just not operating it.

Dec 26, 2013 | Cars & Trucks

1 Answer

1995 sonoma clutch pedal won't move


''Throw out bearing'' has destroyed itself.... time to pull the transmission and replace it and the clutch and pressure plate, and turn the fly wheel smooth.

Feb 05, 2013 | 1995 GMC Sonoma

1 Answer

So a 1994 mazda mx3 with a manual tranmission. When you hit the accelerator when the car is in gear the car will rev but not actually move. We can push the car without an issue so not a brake locked up...


Colybear18,
All the indications you stated above give a clear indication that the clutches are worn completely. What is required is that you get the gear box serviced - changing the clutch disc will make the diffence you are looking for. The burnt smell you noticed was the complete failure of the clutch plate. Hope this helps.... Do have a good day.

Aug 14, 2011 | 1994 Mazda MX-3

1 Answer

I have a manual transmission in my '04 Mustang. When I begin to depress the clutch, an odd grinding sound starts, not loud but enough to warrant concern. As I drive, the car sounds fine. Switching gears...


Worn throw out bearing, replace or the problem may damage other components. This requires dropping the entire transmission. this bearing sits between the clutch pressure plate and clutch slave assembly. When the clutch pedal is pressed, the bearing makes contact with the spinning clutch pressure plate. If defective, grinding/squealing noises may be heard. If the bearing fully fails, loose debris may damage other components. Replace immediately!!

Dec 11, 2010 | 2004 Ford Mustang

2 Answers

My 2005 Pontiac Sunfire intermittantly grinds when shifting into first gear. This has been happening ever since I took the car in for its 60,000 mile tune-up early this year. I replaced my clutch three...


I believe the problem is the first gear synchronizer. They are what allows the gears to mesh together without grinding. As they wear, they are less able to mesh the gears together without grinding. The first gear gets used the most, so that one usually wears first. Each gear has them, so as time goes on, the others will wear. To replace the synchronizer/s, involves diaasembling the transmission. I would have the transaxle fluid level checked, maybe as simple as that. But usually it's the prior.

May 14, 2010 | 2004 Pontiac Sunfire

1 Answer

Grinding Noise When Clutch Is Depressed, Lights Flicker


you may need to have your clutch cable adjusted ... it is most likely not releasing the clutch fully and grinding against the flywheel

Oct 06, 2009 | 1998 Volkswagen Jetta

1 Answer

Hello, I own a 97 miata and the clutch goes in gear but the car does not move.


Do you mean: The transmission goes into gear but the car does not move? Is somebody in the habit of coasting the car down hills with the clutch in so they don't have to shift? Coasting down a hill with the transmission in a low gear can cause the clutch disc to spin so fast that centrifugal force throws the lining off the disc. I blew up my clutch man! If this is the case you need a clutch job to learn an expensive lesson. Or starting out in second or third gear and slipping the clutch to get the car going. Just as bad just as expensive! Most have been told not to slip the clutch, Not all have been told not to coast in gear. If you like to coast put the transmission in neutral and let the clutch out. If this is not the case then the clutch is hanging up internally, put the car in gear and let is set over night. Can you push it with the clutch up? You shouldn't be able to. Now push the clutch down and let it up. If you can push the car now it is hanging up (sticking) internally. The clutch master/slave hydraulic system needs looked at.

Jun 06, 2009 | 1997 Mazda MX-5 Miata

1 Answer

1991 prelude drivetrain problem


Wow, that's weird! If the speedometer is moving, but you aren't, then yes, something in the axle is not connected to the wheel. Were there any weird noises or symptoms before this happened? Either the cv joint is completely shot (u should have heard noise when turning a long time before this) or the spline could be stripped, but that is something I haven't heard of. If the clutch was shot, the engine would rev, but speedo is connected to transmission, so the speedo would not work if the clutch didn't. Let me know if anything was going on before this happened, I have a 91 Prelude (2nd since 1994, love it). countrycurt0

Sep 16, 2008 | 1991 Honda Prelude

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

699 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...