Question about 2000 Chevrolet Silverado 1500

1 Answer

U joint how expensive can u joints be to repair?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,779 Answers

I checked NAPA website, depending on engine size, trans, etc u joint should be approx. $30. I would think a good garage could do it in an hour. To try and determine if this is the problem you can do the following: Block the front wheels securely, jack up the back of truck (rear wheels off the ground) put truck in neutral (not running!) get underneath locate u joint (it's at the end of driveshaft and in front of the rear axle). Grab onto it with both hands, try to move it back and forth. Depending how bad it is, you should be able to notice some wobble, or play at the u joint. If your truck is full time 4x4, you will not be able to check it this way. Truck should be out of 4X4 to check this way. Grease all the lube points on the suspension twice a year, this will prevent stuff like this wearing out quickly. (some u joints are sealed and can't be greased)A repair manual will show you all the lubrication points, type of grease to use etc for about $20 good luck! countrycurt0

Posted on Aug 09, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Show me hoe to repair a cv joint for a Saturn Vue 2006?


Buy the shaft assembly instead of trying to change the cv joint on your shafts. They aren't much more expensive and will save a ton of time. Remove wheel, brakes, rotors, axle nut. Slip the shaft inward and press out if the hub. Then simply pop it out of the other end. There is a retainer clip on the differential side that springs in and out of place. A prybar or long screw driver helps pop it past the detent.

Jul 22, 2014 | Cars & Trucks

1 Answer

Why does my front passenger tire lean outwards at the bottom and inwards at the top?


The most common problem would be a bad lower ball joint. It could also be bad control arm bushings or a combination of the two. Neither is an expensive repair. This should be checked out and repaired soon as it could cause control issues. Hope this helps.

May 15, 2012 | 2006 Dodge Stratus

3 Answers

Hit a bump the the steering wheel shimmies


most likely cause is a ball joint first suspect is the track rod ends ,possibly even the inner ones on the steering rack ,but it could be a lower track control arm joint or bush as well ,doesnt this vehicle have a yearly mechanical inspection ?? and six months in the case of a commercial vehicle like this one

Jul 02, 2011 | 1996 Ford F350 Crew Cab

1 Answer

I have a bad vibration in overdrive around 50-55 mph on 2004 chevy avalanche


The first palce I would check is the drive shaft and universal joints. These will cause vibrations when they are about to go out. If there is any play at all in the universal joints they need replaced. Not a hard or expensive repair and like I said check them for play before you go any further.

Dec 11, 2010 | 2004 Chevrolet Avalanche

1 Answer

How do i replace a cv joint on 1999 cadillac eldorado


lots of trouble and expense and all you get is one new joint. trade that labor expense and for about the same money get a new or reconditioned axle that has 2 good cv joints, boots, and new axle. and you can change out the whole axle yourself much easier than the joint.

Sep 04, 2010 | 1999 Cadillac Eldorado

2 Answers

I think the front-right CV joint may be going out on my 2003 Solara SLE (it makes a funny noise when I turn the car while I am driving, but not from a complete stop). What would be the least expensive...


If it is the CV joint (and it does sound like it is), the least expensive option will be to replace the CV joint. This is really the only solution available, but the popping or funny noises can also indicate other worn parts such as struts, shocks, tire rod ends, and even the rack and pinion in your steering system. I would check all of this before going through the aggravation of replacing the CV joint.

Jul 24, 2010 | 2003 Toyota Camry Solara

1 Answer

I need a repair manual for a 1990 rolls royce silver spur2 i want to put ball joints and front end parts in my self


the repair manuals for any rolls royce are sold only by rolls royce and are quite expensive. call albers rolls royce in zionsville, indiana (317)873-2360

Dec 30, 2009 | 1991 Rolls Royce Rolls Royce Silver Spur

1 Answer

Banging noise out of the center of the car whenever i make a right turn


hi, the problem your having could be one of a couple of things.
1. it could be the track rod end coming from the steering rack this is a common fault all cars get from time to time its not expensive to repair but will need specialist tools
2. It could be the bottom ball joint but if it was going to be this then you should hear a knocking noise when you go over bumps etc.
3. the wheel bearing itself could be on the way out the parts for this are not expensive but their is alot of work involved in doing this repair.

With all 3 jobs your going to need specialist tools of some kind ie ball joint splitter, tracking rods to reset the track rod ends to ensure the wheels are at the right angle.

Hope this is some help to you let me know if you need further assistance ok

Aug 19, 2009 | 2008 Honda Accord

2 Answers

What's involved in changing out cv joints on a 96 grand cherokee?


the joint is fairly easy to change. the hardest part is getting the hub assembly off. you will need a36mm sokcet for the hub nut.i had to use an 18" breaker bar to remove it.

Aug 11, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...