Question about 1989 Plymouth Sundance

1 Answer

'89 plymouth sundance

My cars engine stopped while driving. someone told me about turning the car on twices, then counting the blinks of the service engine light to know the code of which will let me know what is wrong with my car. well, did it - the code was 3/2/5/5. what does this mean in regards to the fact that my cars ignition spins but does not start? email angelat3@yahoo.com

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

You need a timing belt

Posted on Feb 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What operates the doors for the air conditioner and heater controls in a 1992 Plymouth Sundance 2.5 engine


www.ask.com/1992/Plymouth/Sundance/2.5L/service-manual/
/troubleshooting-guide/
/wiring_diagrams/
/air-vent-layout/diagrams/
/door/diagrams/layouts/
/air-condition-layout-diagrams/
/ventilation diagrams/
/heat-duct-layouts-diagrams/
/what every you want or need/

Apr 23, 2015 | Plymouth Cars & Trucks

1 Answer

1991 sun dance dies in middle of road will not start. The check engine light blinks 2 short 3 quick. Could this be a timing belt?


Your timing belt could be broken or perhaps the Drive chain that drives the two balance shafts behind the timing belt

Dec 15, 2012 | 1991 Plymouth Sundance

1 Answer

My Plymouth sundance 1994 2.5l Auto seat belt will not move. The light stays on the dash board, and when i run my blower to high or to much current, my speed gauge goes to zero and the mileage stops...


Hm. auto seat belt not moving points to a burnt out motor or a fuse is blown.

Have you had the starting and charging systems tested by Sears or Walmart?

How does it start?

Jul 10, 2010 | 1994 Plymouth Sundance

3 Answers

WATER PUMP LEAKING


front of the engine see picture below.

2da1ac1.jpg

Mar 09, 2010 | 1992 Plymouth Sundance

1 Answer

Where is the relay located for the turn signals on an 89 plymouth sundance? The lights work on the signals, but don't blink when you turn them on


your fuse block is located behind the steering column cover acessible by removing the fuse access panel above the hood latch release lever.the relay and flasher module is located behind an access panel in the glove box.included in the module are hazard and turn signal flashers along with time delay and horn relays.you have additional relays mounted on the inner fender panel near the battery and strut tower.

Dec 13, 2009 | 1994 Plymouth Sundance

1 Answer

I have a 93 Plymouth Sundance that has been running good until just a few days ago. When I now start it up, when stepping on the gas to head down the road, I can hold the pedal to the floor and it will...


Start with cycling your key, on ,off, on, off, on, leave on (not start)and count if check engine light flashes. For example: flash,flash,pause, then 2 more flashes is code 22. 3 flashes, pause then 3 more, is code 33 etc... Code 55 is end of message. Get back to us if you get any.

May 07, 2009 | 1993 Plymouth Sundance

1 Answer

Intermittant loss of acceleration on my 1991 plymouth sundance


Turn key, on, off, on, off, on & leave it on (not start) & count check engine flashes. 2 digit codes, for example: flash, flash, flash, pause, flash,flash., is code 32

Mar 29, 2009 | 1991 Plymouth Sundance

1 Answer

Key stuck in ignition on 89 plymouth sundance


Without taking the ignition apart, you will really have to do some work, what you might want to do is get in the passenger side, grab the key with a good set of pliers, and get some leverage. If you grab, move the key back and forth while jiggling the wheel, the lock should come loose and the key should slide out. Be careful not to turn the key too far, because then you'll break it off, hope that works.

Feb 18, 2009 | 1989 Plymouth Sundance

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...