Question about 1996 Land Rover Range Rover

1 Answer

1996 range rover 4.0

I get shacking in the front when going about 35-40mph and when i speed up it stops.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 53 Answers

Get your tyre balance.

Posted on Oct 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change ignition coil pack p38 range rover


1996-1999 remove 4 nuts and peel out from top.
2000-2002 remove upper plenum

Dec 30, 2012 | 1996 Land Rover Range Rover

1 Answer

Why doesnt my 1996 range rover not speed up when i acelerate da gas after i recently replaced the updated fuel pump?


This is just a WAG, but I would say you didn't replace the fuel filter after you replaced the fuel pump. Sometimes a stronger fuel pump also pump more of the accumulated gunk from your tank into the fuel system, so the filter clogs up faster.

Jun 24, 2011 | 1996 Land Rover Range Rover

1 Answer

Front Blower stop working in my 03 range rover


check fuse/check blower rheostat/ rheostat is next to blower motor/rheostat controls blower speeds

Mar 14, 2011 | 2003 Land Rover Range Rover

1 Answer

My 1996 Range Rover A 4.6 ltr motor has developed a rattle in bearings. I have removed the front housing with oil pump and can not see any thing wrong. I have heard that this motor has had trouble with...


bearings don't rattle --they knock and the knock gets louder with rpm
it has a chain drive for the cam shaft and rattles are associated with a worn chain as there is no slack adjuster
The v8 engine (originally a 4 litre ) was only stroke by 10 mm to give it extra power
there was never any problem with the block from cracking as that engine was used in the Leyland truck and p38 car as well as range rover cars and off road vehicles
it's big draw card was the power to weight ratio being an aluminium cast block it was suited to fast car applications

Dec 02, 2017 | 1996 Land Rover Range Rover

2 Answers

HOW DO I MAKE THE CRUISE CONTROL WORK IN A 1996 RANGE ROVER I DONT HAVE A MANUAL


check vacuum pipes[rubber about 6mm bore] for cracks/splits or even disconnetion. repair pipe and reconnect.
some where near firewall diagonally opposite battery

Feb 15, 2010 | 1996 Land Rover Range Rover

1 Answer

What wrong?


Hi Axer,

The Range Rovers have permanently engaged Four Wheel Drive. If the tires are different sizes, they're spinning at different rates. Or trying to.

If you were off-road, it wouldn't matter too much, but on paved road, where the tires tend to grip not slip, these different rates subject a locked drive train to tremendous stress. This can bind up the gearing in the transfer case. Hopefully after only ten minutes, no permanent damage was done.

You can relieve this stress by jacking one end completely off the ground. Front or back. As the tires lose their grip on the road, you should see them spin slightly. That's good news. Once released you should be able to move again.

While it's in the air, you should probably put the original size tires back on. So choose which end to jack accordingly.

Comment me back to let me know how it goes.
Good luck

Mike



Jan 24, 2009 | 1995 Land Rover Range Rover

4 Answers

1996 4.0 Range Rover won't unlock


This car is in super lock mode... when you press remote 2times to lock or when you lock with remote and try to unlock using key manually.

there is a 4 digit number to open the door, its like opening a safe, starting from the left(key in car door) it goes L/R/L/R. so if number code is 1234..... left 1, right 2, left 3, right 4.

or if this too troublesome you can ask landrover dealer to remove the KEYCODE.

happy trying.....
adrian/kk.

Jan 10, 2009 | 1996 Land Rover Range Rover

1 Answer

Land Rover Range Rover


u can use a compressor to lift the car, manually insert to air pipe. if there is no leak in the system the car will stay up. but this for emergency only.

u need to send the car to workshop for proper repair.

the reason u cannot lift the car is pump is faulty, leak in the system, relay problem.

Oct 08, 2008 | 1996 Land Rover Range Rover

Not finding what you are looking for?
1996 Land Rover Range Rover Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

yadayada
yadayada

Level 3 Expert

77499 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...