Question about 1993 Mercedes-Benz 190

1 Answer

1988 190 how to remove a/c blower

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercedes-Benz Master
  • 21,949 Answers

Under the dash passenger side

Posted on Dec 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change ac blower on a 2001 chevy silverado with the 5.3 liter v8


With Delphi Blower Motor
  1. If equipped, remove the sound insulator panel.
  2. Remove the blower motor insulating cover screws.
  3. Disconnect the electrical connector from the blower motor.
  4. Remove the blower motor insulating cover.
  5. Pull the retaining tab down while turning the blower motor counterclockwise in order to disengage the blower motor from the heater/ventilation module.
  6. Remove the blower motor.

With Visteon Blower Motor
  1. Remove the sound insulator panel.
  2. Disconnect the electrical connector from the blower motor.
  3. Remove the screws from the blower motor.
  4. Remove the blower motor from the HVAC module.
  5. Remove the retainer from the blower motor wheel. Discard the retainer.
  6. Remove the blower motor wheel from the blower motor.

Jul 27, 2014 | 2001 Chevrolet Silverado

1 Answer

Want to change fan on blower heater


Removal

  1. Remove wiper arms.
  2. Remove cowl panel.
  3. Disconnect blower motor electrical connector and vent tube.
  4. Remove blower motor retaining screws.


  1. Remove fan retaining nut from blower shaft through plenum opening while holding the fan from the engine compartment.
  2. Remove fan from blower motor while removing blower motor from vehicle.
Installation

  1. Hold fan through plenum opening.
  2. Install blower motor to vehicle while installing fan to blower motor.
  3. Install fan retaining nut to blower motor shaft through plenum opening.
  4. Install blower motor retaining screws.
  5. Connect electrical connector and vent tube.
  6. Install cowl panel.
  7. Install wiper arms.

Aug 13, 2013 | 1991 Oldsmobile Cutlass Ciera

1 Answer

The heater blower stopped working and the fuse is not blown?


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Feb 08, 2011 | 1996 Chevrolet Blazer

1 Answer

How to change blowermotor on 2001 gmc jimmy


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Dec 08, 2010 | 2001 GMC Jimmy

2 Answers

Where is the blower motor located on a 91 Dodge Dakota and how do I access it?


Blower Motor REMOVAL & INSTALLATION Dakota
  1. Disconnect the negative battery cable.
  2. Remove the steering column cover, intermittent wiper control and the lower instrument panel module retaining screw to the right of the steering column.
  3. Remove the center distribution duct retaining screws and panel support screw at the bottom of the module. Fig. 1: Heating/air conditioning unit components - Dakota models 88476g01.gif

  4. Remove the courtesy lamp at the lower right corner of the module and the screw near the ash receiver.
  5. Open the glovebox and remove the screws along the top edge.
  6. Move the module out and down far enough to unclip the wiring harness and antenna cable and disconnect the speaker wire (if equipped with monaural radio) and glovebox light wire. Remove the module from the vehicle.
  7. If the vehicle is equipped with air conditioning, disconnect the two vacuum lines from the recirculating air door actuator and disconnect the blower lead wires.
  8. Remove two screws at the top of the blower housing, five screws from around the housing and remove the blower housing from the unit.
  9. Remove three screw attaching the blower to the unit and remove the blower from the vehicle.
  10. Remove the fan from the blower motor.
  11. Installation is the reverse of removal. Secure all components accordingly and check the blower motor for proper operation.
Pick-Up and Ramcharger
  1. Disconnect the negative battery cable.
  2. Disconnect the blower wiring. Fig. 2: Exploded view of the heater assembly components for Pick-up and Ramcharger models 88476g00.gif

  3. Remove the blower motor cooling tube. Fig. 3: Disconnect the wiring and cooling tube to access the blower motor - 1994-96 models shown 88476g06.gif

  4. Remove the screws or retaining nuts retaining the blower plate to the housing. Fig. 4: Unplug the wiring harness connector to the blower motor 88476p14.jpg
    Fig. 5: Unfasten the blower plate housing screws 88476p15.jpg

  5. Remove the assembly from the housing. Fig. 6: Lift away the blower plate housing for access to the blower motor 88476p16.jpg

  6. Remove the spring clip fastening the blower wheel to the blower shaft and pull off the wheel. Remove the blower from the plate. Fig. 7: Unclip and remove the blower wheel 88476p17.jpg

  7. Installation is the reverse of removal.
prev.gif next.gif

Oct 14, 2010 | 1991 Dodge Dakota

1 Answer

How to install a front blower motor in a 96 ford explorer


Blower Motor - REMOVAL & INSTALLATION
(see Figures 1 and 2)

8e5714d.jpg

Fig. 1: Exploded view of the blower motor mounting

ff3bdf8.jpg

Fig. 2: Exploded view of the blower motor and wheel (fan) assembly

Without Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the air cleaner or air inlet duct, as necessary.
  3. If necessary, Remove the speed control module and the washer fluid reservoir.

2587a00.jpg

Fig. 3: To remove the blower motor, first disconnect the electrical wire harness plug...

f234e79.jpg

Fig. 4: ...then remove the blower motor cooling tube from the motor
  1. Disconnect the wire harness connector from the blower motor by pushing down on the connector tabs and pulling the connector off of the motor.
  2. Disconnect the blower motor cooling tube at the blower motor.
3bbd0e1.jpg

Fig. 5: Remove the blower motor attaching screws and the washer fluid reservoir...

8da3ac1.jpg

Fig. 6: ...then slide the blower motor from the housing. Take care to not damage the blower wheel (arrow)
  1. Remove the 2 screws attaching the blower motor and wheel to the heater blower assembly.
  2. Holding the cooling tube aside, pull the blower motor and wheel from the heater blower assembly and remove it from the vehicle.
  3. Remove the blower wheel push-nut and/or clamp from the motor shaft and pull the blower wheel from the motor shaft.
To install:
  1. Install the blower wheel on the blower motor shaft.
  2. Install the hub clamp and/or push-nut.
  3. Holding the cooling tube aside, position the blower motor and wheel on the heater blower assembly and install the 2 attaching screws.
  4. Connect the blower motor cooling tube and the wire harness connector.
  5. Install the vacuum reservoir on the hoses with the 1 screws.
  6. If removed, install the speed control module and the washer fluid reservoir.
  7. Install the air cleaner or air inlet duct, as necessary.
  8. Connect the negative battery cable and check the system for proper operation.

With Air Conditioning
  1. Disconnect the negative battery cable.
  2. In the engine compartment, disconnect the wire harness from the motor by pushing down on the tab while pulling the connection off at the motor.
  3. Remove the air cleaner or air inlet duct, as necessary.
  4. If necessary, remove the solenoid box cover retaining bolts and the solenoid box cover.
  5. Disconnect the blower motor cooling tube from the blower motor.
  6. Remove the blower motor mounting plate attaching screws and remove the motor and wheel assembly from the evaporator assembly blower motor housing.
  7. Remove the blower motor hub clamp from the motor shaft and pull the blower wheel from the shaft.
To install:
  1. Install the blower motor wheel on the blower motor shaft and install a new hub clamp.
  2. Install a new motor mounting seal on the blower housing before installing the blower motor.
  3. Position the blower motor and wheel assembly in the blower housing and install the attaching screws.
  4. Connect the blower motor cooling tube.
  5. Connect the electrical wire harness hard shell connector to the blower motor by pushing into place.
  6. If removed, position the solenoid box cover into place and install the 2 retaining screws.
  7. Install the air cleaner or air inlet duct, as necessary.
  8. Connect the negative battery cable and check the blower motor in all speeds for proper operation.

Hope this help (remember comment and rated this).

Apr 23, 2010 | 1996 Ford Explorer

1 Answer

My heater and ac dont work but the blower motor turns on?


REMOVAL PROCEDURE
  1. Remove the right closeout panel.
  2. Remove the blower motor wire harness connector. spacer.gif 2009-08-23_145458_37.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  3. Cut out the blower motor using a utility knife in the narrow groove of the lower case. IMPORTANT: Cut through the case as straight as possible because the motor cup must be replaced. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
  4. Remove the blower motor
  5. Remove the blower motor nuts. spacer.gif 2009-08-23_145605_38.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  6. Remove the blower motor from the blower motor cup.
INSTALLATION PROCEDURE
  • Install the new blower motor to the blower motor cup.
  • Install the blower motor nuts.
  • Install the motor blower seal to the blower motor service ring.
  • Install the blower motor. spacer.gif 2009-08-23_145704_39.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  • Install the blower motor attachment ring.
  • Install the blower motor screws.
  • Install the blower motor wire harness connector.
    1. Install the right closeout panel.
  • Apr 15, 2010 | 2001 Chevrolet Impala

    1 Answer

    How to replace the blower motor fan assembly in a 2000 GMC Yukon XL K1500 4X4


    Blower Motor Removal & Installation Delphi
    Blower Motor Replacement (Delphi)

    1fb4643.gif
    To Remove:
    1. Remove the instrument panel sound insulator panel (if equipped).
    2. Disconnect the electrical connector from the blower motor.
    3. Remove the blower motor insulating cover screws.
    4. Remove the blower motor insulating cover.
    5. Pull the retaining tab down and rotate blower motor counterclockwise to remove.
    To Install:

    1. Position the blower motor and turn assembly clockwise until tab locks in place.
    2. Install the blower motor insulating cover.
    3. Connect the electrical connector to the blower motor.
    4. Install the instrument panel sound insulator panel (if equipped).

    Visteon

    Blower Motor Replacement (Visteon)

    878e8d8.gif
    To Remove:
    1. Remove the instrument panel sound insulator panel (if equipped).
    2. Disconnect the electrical connector from the blower motor.
    3. Remove the blower motor screws.
    4. Remove the blower motor from the HVAC module.
    To Install:
    1. Position the blower motor and install mounting screws.
    2. Connect the electrical connector to the blower motor.
    3. Install the instrument panel sound insulator panel (if equipped).

    Oct 02, 2009 | 2000 GMC Yukon XL

    1 Answer

    I have a 2000 ford E350 van with front and rear air. the front blower motor runs at low speed, The front blower still runs on low even when the knob is set on medium or high. I do not know where the...


    it's either the blower motor switch or blower motor resister. Resistor ?Heater Blower Motor Switch Removal Remove the battery (10655) ; refer to Section 414-01 . Remove the battery tray. Remove the screws. Remove the battery tray. Disconnect the heater blower motor switch resistor connector. Remove the heater blower motor switch resistor (18591). Remove the two screws. Remove the heater blower motor switch resistor. ----------------------------------- Switches Removal Disconnect the battery ground cable. Remove the center trim panel; refer to Section 501-12 . Remove the control assembly. Remove the screws. Remove the control assembly. Remove the A/C-heater function selector switch knob. Disconnect the vacuum harness connector. Disconnect the A/C-heater function selector switch connector. Remove the A/C-heater function selector switch. Remove the screw. Remove the A/C-heater function selector switch. Remove the temperature control switch knob. Disconnect the temperature control switch connector. Remove the temperature control switch. Remove the screw. Remove the temperature control switch. Remove the heater blower motor switch knob. Disconnect the heater blower motor switch connector. Remove the heater blower motor switch (18578). Remove the screw. Remove the heater blower motor switch. ----------------------------

    Mar 31, 2009 | 2007 Ford E-350 Super Duty Length XLT

    Not finding what you are looking for?
    1993 Mercedes-Benz 190 Logo

    Related Topics:

    34 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercedes-Benz Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Michael Contreras
    Michael Contreras

    Level 2 Expert

    164 Answers

    Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...