Question about 1994 Ford Thunderbird

1 Answer

Maf sensor, were is it located

The vehcle is a 1994 ford thunderbird. the engine has a v8. I need to know were to find the maf sensor so i can instal the new maf sensor.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Near the throttle body, in the intake tube from the filter

Posted on Aug 11, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 ford thunderbird 4.6 v8 randomly turns off while driving wait few mins starts up can go for awhile before it happens again


Read freeze frame data to see what dies. Possible causes crank sensor gem module fuel pump ignition switch

Feb 02, 2014 | 1994 Ford Thunderbird

1 Answer

1994 Ford Thunderbird 4.6/V8- diagnostic codes: P0171 & P0174. What do they mean?


Basically this means that an oxygen sensor in bank 1 detected a lean condition (too much oxygen in the exhaust). On V6/V8/V10 engines, Bank 1 is the side of the engine that has cylinder #1.

Note: This DTC is very similar to P0174, and in fact your vehicle may show both codes at the same time.
Symptoms

You will more than likely not notice any drivability problems, although there may be symptoms such as a lack of power, detonation (spark knock), and/or a hesitation/surge on acceleration.
FB.init("dd7d9e9681341cde77587bc6a2029f6f"); OBD-Codes.com on Facebook Causes

A code P0171 may mean that one or more of the following has happened:

  • The MAF (Mass Air Flow) Sensor is dirty or faulty. Note: The use of "oiled" air filtersmag-glass_10x10.gif may cause the MAF to become dirty if the filter is over-oiled. There is also an issue with some vehicles where the MAF sensors leak the silicone potting material used to protect the circuitry.
  • There could be a vacuum leak downstream of the MAF sensor.
Possible Solutions

Possible solutions include:

  • In the vast majority of cases, simply cleaning the MAF sensor does the trick. Consult your service manual for it's location if you need help. I find it's best to take it off and spray it with electronics cleaner or brake cleaner. Make sure you are careful not to damage the MAF sensor, and make sure it's dry before reinstalling
  • Inspect all vacuum and PCV hoses, replace if necessary
  • Check for a dirty fuel filter

Jan 28, 2011 | 1994 Ford Thunderbird

2 Answers

1996 Ford Thunderbird V8 4.6L Idles High. When starting up engines does not idle down after warming up. When driving car just wants to speed up.


check your throttle body make sure all the springs are connected. your throttle body may be nasty inside and may need cleaning, it may be getting stuck. Throttle cable could be sticking or disconnected (there are two one pulls and one returns to idle IIRC)

also you should really search www.tccoa.com and become a member there if you are not already.

Oct 10, 2009 | 1996 Ford Thunderbird LX

1 Answer

I need firing order for ford thunderbird 1994 4.6l v8.


My recollection is #1 is front passenger side, #5 is front dirver side.

Please rate if this is what you need.

May 09, 2009 | 1994 Ford Thunderbird

1 Answer

Where's my O2 sensor located


Heated Oxygen Sensor (HO2S) SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Oxygen Sensor Wrench T94L-9472-A
Removal and Installation
NOTE: If excessive force is needed to remove heated oxygen sensor (HO2S) (9F472) , lubricate heated oxygen sensor with penetrating oil prior to removal.
  1. Disconnect battery ground cable (14301) .
  1. Disconnect heated oxygen sensors from engine control sensor wiring (12A581) .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Remove heated oxygen sensors from dual converter Y pipe (5F250) using Oxygen Sensor Wrench T94L-9472-A.
  1. To install, reverse Removal procedure. Tighten heated oxygen sensors to 36-46 Nm (26-34 lb-ft).

980db4e.gif

Feb 22, 2009 | 1994 Ford Thunderbird

1 Answer

Misfire and small of gas


had same problem on my 94 v8 bird try replacing the mass air sensor fixed the same issues on mine

Jan 11, 2009 | 1994 Ford Thunderbird

Not finding what you are looking for?
1994 Ford Thunderbird Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...