Question about Daewoo Leganza

Open Question

I had P1441 code when i scanned my 2002 Daewoo laganza what engine fault has my car developed? thank you

Posted by on

  • Anonymous Sep 27, 2008

    nwjqejk

  • sledhead64 Jan 31, 2009

    same problem, same code on a 2000 Leganza. I know it's something to do with the evaperative purge, but I don't know where to start looking.

×

5 Suggested Answers

emissionwiz
  • 61249 Answers

SOURCE: 1996 monte carlo fault codes po300, 441, 705,

THESE ARE FROM THE GM CODE DIFINITION MANUAL, U NEED TO TAKE THIS TO THE DELAER, U HAVE SOME SERIOUS PROBLEMS TO GIVE THIS MANY CODES.

P0300 - Engine Random Misfire Detected
P0441 - Evaporative Emission Control System Incorrect Purge Flow
P0705 - Trans Range Switch Circuit
P1106 - Manifold Absolute Pressure (MAP) Sensor Circuit Intermittent High Voltage
P1133 - Heated Oxygen Sensor (HO2S) Insufficient Switching Bank 1 Sensor 1
P1441 - Evaporative Emission (EVAP) System Flow During Non-Purge
P1662 - Cruise Lamp Control Circuit
P1672 - Low Engine Oil Level Lamp Control Circuit
P1870 - Transmission Component Slipping

Posted on Mar 24, 2009

  • 1348 Answers

SOURCE: what those code p1441 manufacturer control auxiliary emission controls mean

what you want to do is take it to nissan and scan it with the consult2 diagnostic system to tell you which of the many things in the system have failed.
the EGR is the most common.

Posted on May 28, 2009

REDOIL
  • 355 Answers

SOURCE: 2002 Volvo S60 with Engine fault codes

THE 445 IS THE EVAP PURGE VALVE IT MAY BE BAD BOTH 446 IS SAME VAVLE YOU NEED TO SEE IF THE HOSE ARE GOOD ON THIS VAVLE MAKE SHERE NO CRACKS IF NOT PULL HOSES AND SEE IF SOMTHING IN VAVLE ITS NEAR THE CANSTER AND THAT IS NEAR THE GAS TANK UNDER CAR PUT CHECK GAS CAP MAKE SHERE ITS TIGHT HOPE THIS HELPS

Posted on Sep 15, 2009

  • 1986 Answers

SOURCE: How to scan the 2001 daewoo nubira fault codes.

Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Posted on Sep 30, 2009

djpstunt1
  • 172 Answers

SOURCE: where to find 2002 daewoo

you can go to the junk yard or call the dealer

Posted on Dec 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Getting Code #P1627 on a 2000 Daewoo Laganza


the TCM/engine control module is showing up as faulty--- A/D conversion malfunction === causes are the tcm/ ecm

Dec 14, 2013 | Daewoo Leganza Cars & Trucks

1 Answer

Where to find 2002 daewoo laganza fuel tank clamps?


you can go to the junk yard or call the dealer

Dec 29, 2010 | 2002 Daewoo Leganza

1 Answer

My deforter from rear window not work daewoo 2002 laganza 16-val 4 cilinder


check the fuse, and the relay under the hood, one is bound to be bad.

Dec 04, 2010 | 2002 Daewoo Leganza

1 Answer

I have a 2001 daewoo laganza that has a cylinder 3 missfire. I have changed the plugs and wires, but the car still gets horrible gas mileage and is still missfiring. Car runs like **** up until I get it to...


My 2001 Daewoo Laganza also showed this problem. It turned out that my valve cover gasket was
not seated properly and oil was accumulating around the spark plug of the #3 cylinder. Replaced gasket and engine started running fine.

Dec 03, 2010 | 2001 Daewoo Leganza

1 Answer

My manual 1998 Daewoo Laganza has developed a fast idle when the engine is warm (1500 rpm +)how does one restet the idle point. Note the idle stop on the Inlet manifold has not moved is locked tight.


The idle is controled by the idle air control motor. I would check for vacuum leaks first and check to see if you have any codes. you cannot adjust the idle yourself. let me know

Jun 17, 2010 | Cars & Trucks

1 Answer

What should the fuel pressure be on a 2002 daewoo laganza 2.2 liter?


The fuel pressure should a minimum of 30 psi and a max of 45

Oct 28, 2009 | 2002 Daewoo Leganza

1 Answer

How to scan the 2001 daewoo nubira fault codes.


Your port should be located under the dash on the driver's side near your knee area. The port should be pointing straight down from the dash. The scanner will be plug and play and you shouldn't have to jump and pins for the OBD-II port. As for the codes, there are so many thousands of codes that you can't even guess what codes will be generated from your scan

Sep 30, 2009 | 2001 Daewoo Nubira

1 Answer

Gas tank on a 1999 daewoo laganza


hi
I think you have problem in fuel tank ventilation the (EVAP) system do to ventilate the fuel tank and pull up fuel vapor to the engine
may be there is blocked pipe or electrical fault in valve (EVAP system) in engine room

Jun 21, 2008 | 1999 Daewoo Leganza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

388 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...