Question about Mitsubishi Eclipse Spyder

1 Answer

Check engine light just came on DTC P0510 what needs to be done to fix it.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 373 Answers

Hi.....
The CODE : P0510. Is .. Throttle Position switch mal funtion.

The Step to fix this problem.
1- Check the connection of the TPS. Throttle position sensor.
2- Check visual the condittion of the sensor. fro breack down.
3- Check the wires for damaged shield covers. corrotion on the pins connector.
4- Clear the Code with the scanner.
If the code RETURN. REPLACE the TPS sensor.

OK... I hope this help on your problem.

Thank you for use fixya....

Posted on Aug 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 sl500 check engine light reset and comes back on after it sits over night. any idea?


What code is it throwing ? Some codes are what are called two trip codes ! You clear the codes an start an drive the vehicle ,no check engine light . Park the vehicle over night an bam next time you start an drive the vehicle the check engine light comes back on .

??There are two types of DTC's, 1 trip DTC's and 2

trip DTC's

??A 1 trip DTC is for a condition that requires

immediate attention such as a catalyst damaging

misfire.

??A 2 Trip DTC is one that a condition must be found

during 2 consecutive trips such as an EGR fault.

??Most Monitors do not set a DTC and light the MIL

when a vehicle fails a test for the first time during a

DRIVE CYCLE. If a test is failed on a second

consecutive DRIVE CYCLE the MIL will light and a

DTC is stored in the vehicles powertrain control
module (PCM).

Feb 07, 2016 | Cars & Trucks

1 Answer

Location for 2006 buick rainier EVAP purge solenoid


You should have an EVAP leak test done . It could be a leaking purge valve , you could need a new gas cap as well or it could be the fuel filler neck . or assorted hoses or the fuel tank pressure sensor . If the check engine light is lit there will be a code .
DTC P0442: Evaporative Emissions (EVAP) System Small Leak Detected or
DTC P0455: Evaporative Emission (EVAP) System Large Leak
DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
You have to jack up the vehicle , the purge valve is attached to the engine behind the A/C compressor .

Dec 01, 2015 | 2006 Buick Rainier

1 Answer

2000 volkswagon beetle epc sensor light on car will not start.... trying but will not turn over. is there any way to get it started...stranded


First of all you need to access the Engine Control Module (ECM) using suitable diagnostic equipment (VAS, VAG-Com, or similar) connected to the data link connector of the car, in order to pull out all DTC's memored. DTC = Diagnostic Trouble Code. Then you will bu full informed about the root cause of the problem, and you will be able to repair & replace bad pieces and reset the ECM. Then the EPC (Electronic Pedal Control) yellow light will turn OFF.
The check engine light (MIL = Malfunction Indicator Lamp):
tdisline_743.jpg


The check engine light & EPC light:
tdisline_744.jpg

Let me know please about found DTC's. I will assist you kindly to fix the problem.

Aug 25, 2011 | 2000 Volkswagen Beetle

1 Answer

2000 vw beetle mil light is on


First of all you need to access the Engine Control Module (ECM) using suitable diagnostic equipment (VAS, VAG-Com, or similar) connected to the data link connector of the car, in order to pull out all DTC's memored. DTC = Diagnostic Trouble Code. Then you will bu full informed about the root cause of the problem, and you will be able to repair & replace bad pieces and reset the ECM. Then the check engine yellow light will turn OFF.
The check engine light (MIL = Malfunction Indicator Lamp):
tdisline_743.jpg

Let me know please about found DTC's. I will assist you kindly to fix the problem.

Aug 25, 2011 | 2000 Volkswagen Beetle

2 Answers

My check engine light came on. The dealership said "filler neck leaking causing evaporative leak." The gas cap also says "loose cap will turn on check engine light." Would like to try a new gas cap but...


sad to say sir that how to clear the code is not easy in manual clearing, you need diagnostic tool to clear the dtc, but some dtc will cleared by 20-50 consecutive warm up if no other trouble code detected by the computer

Jun 19, 2010 | 2001 Chrysler Town & Country

3 Answers

How to reset the check engine on a 208 chevy


Just disconnect the battery (negative terminal) and turn the headlight switch on for about 15 minutes. This should reset the PCM. Otherwise go to Advance and have them hookup the code reader and reset the codes. Thanks

Nov 04, 2009 | 2008 Chevrolet Trailblazer

1 Answer

Temperature gauge not working


Yep!... take it back to the mechanic and tell him/her to recheck the system (there's no such DTC (Diagnostic Trouble Code) as "bad electrical connection"... somebody's pulling your leg!
Whenever the 'CHECK ENGINE' (Service Engine Soon) light comes on, the ECU (Engine Control Unit) sets a Diagnostic Trouble Code (DTC). These codes identify the particular engine management system which caused the light to come on.
You'll need to use/find an OBDII (On-Board Diagnostic) Scanner to retrieve any code(s) which may have been stored in the ECU computer. Afterward, we might be able to help you DIAGNOSE the problem and perhaps eventually fix the problem.

Oct 03, 2009 | 2004 Hyundai Elantra

1 Answer

Engine light is on.


When the check engine light comes on the dash, the computer stores a trouble code(DTC). The computer would need to be scanned to get the code. This code will indicate what system is having a problem. Many of the large parts store chains will do this for free.

A coolant leak can be from any nunmber of sources. A pressure test would need to be done.

Nov 30, 2008 | 2003 Chevrolet Malibu

1 Answer

Cannot turn off the check engine light, recently had dagnostic done and told to change air flow meter, changed it and the light is still on?


To turn off the check engine light(CEL),you must clear the diagnostic trouble code (DTC).This can be done with a scan tool.If you do not have a scan tool,you can disconnect the NEGATIVE battery terminal.Do this for a minimum of 20 minutes to clear the keep alive memory (KAM).Reconnect the battery terminal.If the CEL comes back on again,you have not fixed the problem,or another problem has cropped up,requiring a scan tool to see what DTC has set.

Jul 08, 2008 | 2004 Infiniti G35 Sport Coupe

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

879 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...