Question about 2007 Mazda B4000

1 Answer

Clutch pedal suddenly goes to the floor, no longer [dis]engaging the clutch

Posted by on

  • scorpion_bsk Nov 02, 2008

    I can pump the clutch by hand and get pressure built up, but it loses pressure very quickly. I have tried bleeding the clutch line but it didn't help.

  • George Agios
    George Agios May 09, 2012

    sleve cylinder seal gon,no clatch fluit,or master cylinder seal gon, 4th check for external leak on the system. do this first.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I found that having a wood stick on the clutch pedal down to the floor all night (the other end of the stick held by the seat. oh yeah !!! ) would help to ease shifting for the first hour the next morning, then it would come back stiff and hard to engage in gear.

Posted on Nov 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to diagnose the problem with the clutch that has suddenly stopped working.


does it go to floor --if hydraulic check fluid level possible leak air in system--blown line-- burnt up clutch -bad slave --regular clutch --spring --throw out bearing --broken fork --blown clutch

Aug 29, 2015 | 2000 Hyundai Accent

2 Answers

Clutch pedal fully extended (up) and won't disengage clutch. Happened relatively suddenly.


This may be two possible issues. If your transmission grinded in the past your transmission may have finally given up the ghost. Also your clutch disk may be broken or worn to the point where you can no longer shift. It seems like the latter your going to have to replace your clutch if your a big on doing it yourself a clutch kit is 400$ at autozone. It may be cheaper online good luck I hope this helps

Sep 03, 2014 | 2004 Saturn ION

1 Answer

How to adjust 95 geo tracker clutch


engaging?
you meant dis-engage im sure.
pedal up is engaged,
pedal at floor dis-engages it.
my guess, is the clutch drags unless i push the clutch pedal 100%
to the floor.
1: bad cable is 90% cause. non last this long.
2: no free play is way too loose.
3: broken lever on the pedal top. caused by #1

all fail modes covered here.
http://www.fixkick.com/tranny/clutch/clutch-on-kick.html

Apr 23, 2014 | Geo Tracker Cars & Trucks

1 Answer

Clutch pedal goes almost to the floor before it engages


If your fluid was low (which is why you likely added some,) you may need to "bleed" your clutch master cylinder.

Mar 26, 2014 | 1991 Nissan Stanza

1 Answer

Clutch pedal travel


Your pedal height may be adjustable by a stopper bolt at top of pedal. You would have to check the specification for your car. Most important that the pedal has about a half inch free travel before clutch begins to engage. You need that free play to ensure the release bearing (the throw-out bearing) is not touching the fingers on the pressure plate when not engaged. If it always is touching, it will be rolling around constantly and will go out prematurely.
Your new clutch will allow gear engagement sooner as the clutch pedal is released. I mean gears will engage just as pedal is lifting off from floor. You should notice that difference-the old clutch would have taken longer pedal travel from floor before releasing.

Apr 15, 2013 | Cars & Trucks

1 Answer

Clutch will not engage when it was engaging perfectly to begin with.


Your car has a hydraulic clutch release system, it is defective, either the master or slave cylinder is leaking or pulling in air and this causes the clutch pedal to go to the floor.

Aug 06, 2012 | Cars & Trucks

1 Answer

My clutch pedal used to be pretty stout and the clutch would engage at about the midway point to the floor. All of a sudden the clutch pedal is pretty free to the floor where the clutch now engages. what...


sounds to me like the clutch master cylinder might be bad usually this happens when the line or the clutch master cylinder leaks fluid and you lose pressure to your clutch pedal...you should have a hydraulic clutch on this truck...if its leaking it will need to be replaced its located under the truck usually on the drivers side mounted on the transmission bell housing...hopes this helps

Mar 21, 2011 | 1985 Toyota Pickup

2 Answers

UNABLE TO ENGAGE GEARS WHEN ENGINE RUNNING ( CAN ENGAGE GEARS WITH ENGINE OFF ). CLUTCH PEDAL GOES STRAIGHT TO THE FLOOR WHEN PRESSED


Need to have it check could be clutch master cylinder or slave cylinder or hose from clutch master cylinder to slave cylinder.check brake fluid at clutch master cylinder sit next to brake master cylinder if empty could have a leak. fill and pump peddle and look for leak.

Jan 12, 2010 | 2001 Ford Focus

2 Answers

99 dodge avenger gears will not engage


if it happen all of a sudden then its most likely the clutch slave cylinder.

Dec 07, 2009 | Dodge Avenger Cars & Trucks

1 Answer

Clutch adjustment


its the clutch master and slave unit..... u can get them in a pair with the line all ready bled

Oct 29, 2008 | 1984 Ford F 150

Not finding what you are looking for?
2007 Mazda B4000 Logo

Related Topics:

1,077 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...