Question about 1990 Toyota Pickup

1 Answer

I need to find a copper gasket for the power steering pump.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have one but im in texas
id go to the local parts store and maybe theyll gie you one from a box?

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1998 toyota camry problems


If above the pump, it is usually the cam cover gasket in a Camry.

Jun 24, 2014 | 1998 Toyota Camry

1 Answer

Mercedes 1998 c230 water pump replacement


REPLACE WATER ALL YOU NEED TO DO IS DRAIN THE COOLANT SYSTEM.REMOVE THE ENGINE COOLING FAN AND CLUTCH THEN THE FAN SHROUD.REMOVE ENGINE COVER IF EQUIPPED.THEN REMOVE THE ACCESSORY DRIVE BELT.UNBOLT THE POWER STEERING PUMP MOVE IT ASIDE DONT DISCONNECT ANY POWER STEERING PUMP HOSES.DISCONNECT WATER PUMP HOSES, REMOVE BELT PULLEY THEN REMOVE WATER PUMP MOUNTING BOLTS AND WATER PUMP.CLEAN WATER PUMP MATING SURFACE BE CAREFUL DONT SCRATCH PUMP SURFACE. BESURE WHEN YOU INSTALL NEW WATER PUMP USE GASKET SEALANT ON BOTH SIDE OF GASKET TO KEEP IT FROM LEAKING COOLANT.

Sep 26, 2011 | 2007 Mercedes-Benz C230 Sedan

2 Answers

How can I replace the water pump on a 2004 Grand Prix GTP superchargered?


WELL YOU NEED TO DRAIN COOLANT SYSTEM.PLACE A LARGE DRAIN PAN UNDER THE RADIATOR TO CATCH COOLANT WHILE DRAINING RADIATOR.ONCE ALL COOLANT DRAINED OUT.REMOVE DRIVE BELT.REMOVE WATER PUMP PULLEY.REMOVE POWER STEERING PUMP AND MOVE IT ASIDE.THEN REMOVE WATER PUMP.MAKE WATER PUMP MOUNTING SURFACE CLEAN THEN INSTALL NEW WATER PUMP AND GASKET IN PLACE.IF WATER PUMP GASKET IS PAPER TYPE PUT GASKET SEALANT ON BOTH SIDES OF THE GASKET.IF YOU HAVE RUBBER GASKET DONT USE NO GASKET SEALANT.INSTALL NEW WATER PUMP TORQUE LONG BOLTS TO 25 FT LBS AND TORQUE SHORT BOLTS TO 16 FT LBS.TORQUE WATER PUMP PULLEY TO 115 INCH POUNDS.TORQUE POWER STEERING PUMP BOLTS TO 25 FT LBS.THEN INSTALL DRIVE BELT.FILL THE COOLANT SYSTEM.START THE VECHICLE AND CHECK FOR LEAKS.

Mar 25, 2011 | Pontiac Grand Prix Cars & Trucks

1 Answer

How do I remove the valve cover in order to service lifters?


This si the solution for a gasket replacement, and you will need it when you remove the old ones.
  • Right Side
    • 1

      Disconnect the negative battery cable. Remove the accessory drive belt. Using a 9/16mm wrench, loosen the power steering pump bolts, then slide the pump forward. Do not remove the power steering pump. Remove the power steering pump braces.

    • 2

      Disconnect the spark plug wires. Using a 9/16 mm wrench, remove the valve cover bolts. Lift the valve cover to remove it. Using a flathead screwdriver, gently nudge and remove the old valve cover gasket.

    • 3

      Clean the gasket seating area using automotive engine cleaner and a clean cloth rag. Make sure that all debris is removed. Place the new gasket into place. Apply gasket sealant and place the valve cover back into place.

    • 4

      Tighten the bolts securing the cover into place using a torque wrench. Reconnect the spark plug wires. Reinstall the power steering pump braces. Place the power steering pump back into position. Using a 9/16 mm wrench tighten the bolts that secured it into place. Reinstall the accessory drive belt.

    Left Side
    • 1

      Ensure that the negative battery cable is disconnected. Locate and remove the accessory drive belt. Using a 9/16 mm wrench, disconnect the bolt attaching the alternator to the brace.

    • 2

      Remove the brace to gain access to the additional parts that will be removed. Disconnect and remove the spark plug wire harness. Using a 9/16 mm wrench, remove the bolts securing the valve cover. Lift up and remove the valve cover.

    • 3

      Use a flathead screwdriver to gently nudge the old valve cover gasket to remove it. Do not scratch the gasket seating area when removing the valve cover gasket. Make sure that all debris and particles are removed from the gasket seating area.

    • 4

      Place the new gasket in the gasket seating area. Using a torque wrench tighten the valve cover gasket bolts. Reinstall the spark plug wire harness. Put the alternator brace back into position and tighten the bolt that secures it into place.

    • 5

      Reinstall the accessory drive belt. Reconnect the negative battery cable. Add oil to the car and start the engine. Allow the engine to run idle for 10 to 15 minutes. Drive the car a short distance to check for leaks.

  • Mar 16, 2011 | 1999 Oldsmobile Silhouette

    1 Answer

    Need R&R information to replace for waterpump Geo Storm 1993 4 cyl


    Hi!!
    Here is the Info you requested:
    WATER PUMP REMOVAL & INSTALLATION
    Except Twincam Engines See Figures 1 and 2
    • Disconnect the negative battery cable and drain the cooling system.
    • Loosen the power steering pump adjustment bolts and remove the drive belt.
    • Remove the timing belt; refer to the procedure later in this section.
    • Remove the tension pulley and spring.
    • Remove the water pump mounting bolts, water pump and gasket. Clean the mounting surfaces of all remaining gasket material.
    • To install, reverse the removal procedures. Tighten the water pump bolts to 17 ft. lbs. (23 Nm) and the tension pulley to 30 ft. lbs. (40 Nm).
    • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks.

    FIG 1 1kbron_114.jpg
    FIG 2 1kbron_115.jpg

    Twincam Engines See Figure 3
    1.6L DOHC ENGINE
    • Disconnect the negative battery cable and drain the cooling system.
    • Support the engine using a suitable floor jack and remove the right front engine mount.
    • Remove the engine mount bridge and the upper timing belt cover.
    • Remove the power steering belt and the lower timing belt cover.
    • Loosen the timing belt tension pulley and remove the timing belt.
    • Remove the power steering pump and bracket.
    • Remove the water pump attaching bolts, then the water pump from the vehicle. Thoroughly clean all remaining gasket material from the mating surfaces.
    • Reverse procedure to install and tighten the water pump bolts to 17 ft. lbs. (24 Nm). Connect the negative battery cable and refill the cooling system. Start the engine and check for leaks.
    FIG 3 1kbron_116.jpg
    1.8L ENGINE
    • Disconnect the negative battery cable and drain the engine cooling system.
    • Remove the timing belt covers; refer to the procedure later in this section. Loosen the timing belt tensioner pulley bolt, then remove the belt from the water pump pulley.
    • Remove the 2 bolts from the power steering pump bracket, then position the pump aside with the lines still attached. Be careful not to kink or damage the steering fluid lines.
    • Remove the water pump mounting bolts, then remove the pump from the engine. Thoroughly clean the gasket mating surfaces of all remaining gasket material.

    To install:
    • Install the water pump using a new gasket, then tighten the retaining bolts to 18 ft. lbs. (24 Nm).
    • Position the power steering pump assembly, then install the retaining bolts and tighten to 25 ft. lbs. (34 Nm).
    • Install the timing belt to the pump pulley, then tighten the tensioner pulley bolt to 30 ft. lbs. (40 Nm).
    • Install the timing belt covers.
    • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks
    Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

    Mar 11, 2011 | Geo Storm Cars & Trucks

    2 Answers

    96 chevy G 30 my breaks go out some time, tha powre stering is leaking,it seems when i fill it back up breaks work fine where do i start?


    find out were your leak is? either in the pump itself or the hydrobooster area and replace the component that is leaking fluid

    Jan 22, 2010 | 1993 Chevrolet G20

    1 Answer

    HOW DO YOU TAKE OFF A POWER STEERING LINE? I HAVE A 96 FORD E150 5.8


    When power steering hose replacement is required, follow these steps:
    1. With the engine stopped, remove the return hose at the power steering gear, and allow the fluid to drain from this hose into a drain pan. On some cars, the vehicle must be lifted on a hoist to replace the power steering hoses.
    2. Loosen and remove all hose fittings from the pump and steering gear.
    3. Remove all hose-to-chassis clips.
    4. Remove the hoses from the chassis, and cap the pump and steering fittings.
    5. If O-rings are used on the hose ends, install new O-rings. TRW steering gear cylinder lines have gaskets that are serviced as a unit. The old gasket must be pried out of the fittings in the housing before the new lines and gaskets are installed. Lubricate O-rings with power steering fluid.
    6. Reverse steps 1 through 4 to install the power steering hoses. Tighten all fittings to the manufacturer's specified torque. Be sure all hose-to-chassis clips are in place. Do not position hoses where they rub on other components.
    7. Fill the pump reservoir to the full mark with the manufacturer's recommended fluid. Bleed air from the power steering system. Check the fluid level in the reservoir and add fluid as required.

    Jul 07, 2009 | 1996 Ford Econoline

    1 Answer

    How do you remove the power steering pump on a 96?


    Can't provide pictures, but it's not hard to describe. You will need a normal set of metric sockets... a 13mm and a 17mm if I remember correctly. You will also need an adjustable wrench and screwdrivers. Don't forget lots of towels. The power steering pump is the lowest moving part on the engine. It's on the passenger side in front and to the left of the oil pan. It has two lines and a belt running two it.

    Remove the rubber hose and drain the fluid ( about 1 qt ). Use your adjustable wrench and take the other line off. This is a banjo fitting with two copper gaskets (don't loose them). There are two bolts on the right of the pump. Loosen those, do not remove the bolts yet. There is another bolt on the left with a second, bigger nut... loosen the smaller nut and use your adjustable wrench to back the PS pump back to get the belt off. Now remove all three bolts and the pump should come off. Reassembly opposite of removal. Before starting the engine, fill the PS fluid tank with 1/2 qt to avoid air bubbles in the system. If the power steering doesn't work, you may need to let it sit several hours to let the bubbles in the fluid pop. Good luck.

    Jul 06, 2009 | 1996 Volkswagen Jetta

    1 Answer

    Removing 1994 V8 Ford Thunderbird timing chain cover?


    Have you removed the PS pump pulley? You need to do that to get it off.

    Oct 06, 2008 | 1994 Ford Thunderbird

    1 Answer

    My Mini Coppers steering wheel is hard to turn. What is going on?


    The problem is that your power steering pump is not working, You may need to get it serviced!!

    Oct 01, 2008 | Mini Cooper S Cars & Trucks

    Not finding what you are looking for?
    1990 Toyota Pickup Logo

    Related Topics:

    62 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...