Question about 2005 Dodge Caravan

1 Answer

Seat belt warning

How do you disable the annoying seat belt warning tone?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Dodge Master
  • 60,792 Answers

It is part of the body control module (BCM), it can't be bypassed or disabled.

Posted on Aug 08, 2008

  • edward Jan 10, 2013

    ok Dennis then how do you fix it????

  • yadayada
    yadayada Jan 14, 2013

    Dealer level testing is required.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix or disable passenger seat belt chime? It sometimes goes off for no reason.


There is a switch in the seat that operates when someone is sitting on it. This will operate the seat belt warning if someone sits on it and does not do up their seat belt. It appears that this switch is intermittently faulty. If you remove the seat (usually only 4 bolts) you should find the wires to the switch and can either bypass it or replace it.

Feb 25, 2016 | Seat Cars & Trucks

Tip

Overriding Seat Belt Warning Tone


you don't need a vag comm nothing all you need to do is stick a toothpick in and push down that chrome metal piece till you hear the locking mechanism pop out. it pops out in the middle so you don't wanna push in from the middle rather then the edges. that will disable the warning tone and to enable it just release the belt

on May 19, 2008 | 2007 Audi A4 Convertible

1 Answer

Disable seat belt warning


It can be done using diagnostic cable and appropriate SW.
Cheep hack is to find used buckle (without the belt) and insert it into socket.

Sep 03, 2014 | 2010 Peugeot Partner Tepee

1 Answer

Disable seat belt warning


use a seatbelt male connector off a wrecked car is the easiest way but dont know why you would want to disable the seat belt light as it is a safety warning device

Jul 22, 2014 | Mitsubishi Mirage Cars & Trucks

1 Answer

Prius 2006 disable seat belt warning


check for a wire going into the seal belt buckle. unplug that wire under the seat.

Jan 14, 2014 | 2006 Toyota Prius

1 Answer

How to disable seat belt warning beeps?


First... You should have your passengers wear the seat belts but if you insist you can find the wire going to the seat belt buckle and unplug it under the seat.

Jan 14, 2014 | 2006 Toyota Prius

2 Answers

Seat belt buzzer , how do you turn it off.


Hope this helps ya.. Cobra.. :-)

Belt-Minder® Deactivating/Activating Vehicles Built After 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place the transmission range selector lever in PARK.
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver and passenger safety belts.
Deactivating/Activating
  1. Turn the ignition switch to the RUN position. (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 minute).
  1. NOTE: Step 3 must be completed within 50 seconds after the safety belt warning lamp turns off or the procedure must be repeated.
    For the seating position being disabled, buckle then unbuckle the safety belt 9 times, ending with the safety belt unbuckled.
  1. NOTE: After Step 3, the restraint system warning indicator lamp turns on for 3 seconds.
    Within 10 seconds of the safety belt warning indicator turning on, buckle then unbuckle the safety belt.
  1. The beltminder activation or deactivation is confirmed by the following sequences:
    • If the beltminder is enabled, this procedure will disable the beltminder for that specific seating position. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds to confirm that the deactivation procedure was successful.
    • If the beltminder is disabled, this procedure will enable the beltminder for the specific seating postion. The safety belt warning indicator lamp will flash 4 times per second for 3 seconds followed by a second series of 4 flashes per second for 3 seconds to confirm that the activation procedure was successful.
  1. After confirmation, the deactivation/activation procedure is complete.
Vehicles Built Prior To 5/27/03
Preparation
  1. Before deactivating/activating the belt minder, set the parking brake.
  1. Place gearshift in P (Park) (automatic transmission) or the neutral position (manual transmission).
  1. Place the ignition switch in the OFF position.
  1. Close all the vehicle doors.
  1. Unbuckle the driver safety belt.
  1. Place the parklamps/headlamps switch in the OFF position. (if vehicle is equipped with Autolamps, this will not affect the procedure.)
Deactivating/Activating
  1. Turn the ignition switch to the RUN position (Do not start the engine.)
  1. Wait until the safety belt warning lamp turns off (approximately 1 to 2 minutes).
  1. NOTE: Steps 3 through 5 must be completed within 60 seconds or the procedure must be repeated.
    Buckle then unbuckle the safety belt 3 times, ending with the safety belt unbuckled. This portion of the procedure can be done before or during belt minder warning activation.
  1. Turn the parklamps/headlamps on then off.
  1. Buckle then unbuckle the safety belt 3 times ending with the safety belt unbuckled. After this step the safety belt warning lamp will be illuminated for 3 seconds.
  1. Within 7 seconds of the safety belt warning lamp turning off, buckle then unbuckle the safety belt. This will enable the belt minder if disabled and disable the belt minder if enabled.
  1. The following sequence of events confirm the belt mnider is enabled:
    • flashing of the safety belt warning belt lamp 4 times per second for 3 seconds
    • 3 seconds with the safety belt lamp off
    • flashing the safety belt lamp 4 times per second for 3 seconds again
  1. The safety belt lamp flashing 4 times per second for 3 seconds provides confirmation of belt minder disabled.
  1. After confirmation, the deactivation/activation procedure is complete.


Jun 15, 2010 | 2004 Ford F150

2 Answers

2005 jaguar type-s. How can i disable the belt minder. The seatbelt alrm is making me crazy


To enable or disable the seat belt warning chime on your 2005 Jaguar Type S

1. Ensure the front passenger seat is unoccupied.

NOTE:

Steps two to five must be completed within 60 seconds.

2. Turn the ignition to the RUN position (do not start the engine).

3. Buckle the driver safety belt buckle and wait until the seat belt warning lamp extinguishes.

4. Unbuckle the driver safety belt buckle and wait until the seat belt warning lamp illuminates.

5. Repeat Steps three and four a further eight times.

6. When the driver safety belt buckle is unbuckled for the ninth time a single chime will be heard. The single chime is acknowledgement that the beltminder feature has been disabled.

The beltminder feature will be disabled until the above process (Steps one to six) are repeated. Upon repeating the process the beltminder feature will be reactivated

Apr 25, 2010 | Jaguar S-Type Cars & Trucks

2 Answers

Srs light come on


hi,send your car to dealer to scan the problem,maybe erase fault is require ,or you can found the exact defective part,ty

Mar 23, 2009 | 2002 Mercedes-Benz C-Class

2 Answers

How to disable the speed linked seat belt buzzer in my 2007 camry


Your dealer will use their scan tool to interface with your vehicle; that will disable the speed link. I provide this service at no charge.

Dec 18, 2008 | 2007 Toyota Camry

Not finding what you are looking for?
2005 Dodge Caravan Logo

Related Topics:

154 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...