Question about Porsche 911

1 Answer

What type of Lube grease do you use on a 1988 911 suspension?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Go to pelicanparts.com tech forums for correct info.

Jim

Posted on Aug 09, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Does a mazda 2006 have grease zerks


Check your vehicle's owner's manual service guide; contact the service or parts dept at a local Mazda dealership; visually (look) at the steering linkages, or call your local auto parts store...I know that some models have sealed units with no lube points and others that have lube points...the consideration is model and are the steering components stock or aftermarket?

Mar 22, 2015 | Mazda Cars & Trucks

1 Answer

How to chassis lube a 2010 chevy malibu


You are not taking a boot off the grease fitting. The little rubber boot you're removing is the dust boot for the bleeder valve on the brake caliper. The 2010 Chevy Malibu,as with most cars, have non-serviceable suspension parts.

Feb 23, 2015 | Cars & Trucks

1 Answer

Grease point location


Some original manufacturer suspension parts do not and can not be lubed.

All lube-able fittings should be easily found.

Feb 02, 2014 | 1993 Mercury Grand Marquis

1 Answer

Squeaks going down the road or getting in the vehicle, greased everything that could be greased. Also, AC doesn't work - I think its a vacuum leak. Compressor engages, but only warm or hot air comes out.


try spraying rubber lube on all of the rubber grommets, bushings,and spacers in undercarriage and upper suspension. this worked on my '98 blazer. good luck!
mike

Aug 21, 2013 | 1998 Chevrolet Blazer

2 Answers

Front suspenion. I'm getting a lot of loud creaking when going over bumps and turning corners. I know it's not the C.V. joints. I tried to lube but there are no fitings. Is there a way to lube this...


Dear,

I think the front axles have worned out due to which it makes noise while taking a turn around.

and also get the shockers checked due to which it squeeks while on move.

thanx

May 19, 2011 | 2004 Kia Rio

1 Answer

Can I obtain a diagram that defines the location of the 11 (?) frontend greae zerks for a 2000 Bravada? Jiffy Lube says none of mine will take grease and need to be replaced!


Upper and lower ball joints -4
Both ends of tie rods --4
Ider arm--2
Front Drive Shaft--1

If you just get under the truck you will see them

They have been on that type of suspension for
60 years

I would bet you have one bad fitting at most

I don't know of a single person who would ever
recommend any fast service oil change places
They are a horror story you want to avoid.

Buy a top quality Lincoln Grease Gun with a flex
hose and the proper grease for a GM Vehicle
and do you own
I believe Valvoline #615 is what you want.

Apr 25, 2011 | Oldsmobile Bravada Cars & Trucks

2 Answers

How zerks to lube on 2008 lucerne?


There are no grease zerks.There is nothing to lube on your suspension.Most newer vehicle do not have grease zerks anymore.Hope this helps.Good luck.

Feb 09, 2011 | 2008 Buick Lucerne

1 Answer

What do you lube and grease on the front end of a 2005 Dodge Caravan?


Unless the ball joints or tie rod ends have been replaced there are no grease zerks for the front suspension. Nothing needs to be greased

Nov 11, 2010 | 2005 Dodge Grand Caravan

1 Answer

Noisy front and rear suspension on 2007 suzuki aerio.


it is probly the rubber bushings need some sort of lube between rubber n steel moving parts when car bounces . u'll need 2 SAFELY lift support car while u remove , lube n replace parts unless u can pump grease though a needle (slowly) it would save u alot of wrenching good luck (safely)

Mar 09, 2009 | 2007 Suzuki Aerio

1 Answer

How do i lube my ballbearing joints in my 94- isuzurodeo 4cil.


I think you mean 'ball-joints,' part of the steering and suspension.
Most modern vehicles, with some exceptions, no longer have the Zerk fittings once found on each ball-joint, but 'lifetime' lubrication packed into the joint and decently sealed to prevent loss of grease and incursion of dirt and moisture. You may have sealed ball or roller bearings used in your wheels since the cone-type, adjustable bearings are also less common than they once were.
In my experience, these sealed assemblies have become ever more reliable as materials and manufacturing techniques have steadily improved.  Many such assemblies now really do last the usable life of our vehicles.    

Nov 14, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Dave  C
Dave C

Level 3 Expert

1050 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...