Question about 1990 Toyota 4Runner

1 Answer

When i put into gear and press on the gas and the clutch out the engin revs but the car goes no where.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 417 Answers

Hi,

sounds like your clutch slave cylinder failed, open the hood and look near where you put the brake fluid, the clutch slave fluid is next to the brake fluid reservoir. take the cap off and see if its empty. If its empty that means your clutch slave gaskets failed and its fairly easy and inexpensive to put one of those on, and it takes about an hour. If your familiar with your car you can fix it or have a friend who knows them fix it. You can find resources online and I will send a link,

If the clutch slave reservoir is full you have a more serious problem and I recommend taking it in for an estimate.

http://www.autozone.com/addVehicleId,1640102/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c15280061140#hd1-1-1

J

Posted on Aug 07, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

When put into reverse and gas is pressed car goes nowhere but revs up when car is put in drive and revs to 4000 RPM it just inches forward. Any idea why?


If it's an automatic, is there fluid in the transmission? If the fluid is ok, the transmission is bad. If it's a straight stick, the clutch is bad.

Sep 16, 2015 | 2005 Nissan Sentra

1 Answer

My kx 80 (1992) starts and revs up nice but wen put into gear it hardly moves, the heavyer the person trying to ride it the less it goes, when I lift the back wheel off the floor (no pressure on engine)...


Front wheel drag (locked brake).Bad tire air pressure.If not,is carburetor cloged,need to drain (bolt under) or remove to clean.If the motor revs in the gear ,the clutch slip.Could be bad clutch cable tension or need replace clutch/cable.

Oct 22, 2013 | Cars & Trucks

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

1 Answer

I have a 91 toyota celica that will not go when put into gear.


Have you had problems with clutch slipping up to this point? Like engine revving up and no change in speed while driving. Like going into 4th or 5th gear, letting clutch out, giving gas, and feels like no response? Engine just revs up? That's a slipping clutch.
If that's your problem, you need a new clutch.

Jan 07, 2013 | 1991 Toyota Celica

2 Answers

2008 hyundai accent clutch slipping, i think?


seems a bit early for clutch. how many k's? I would start by checking the intake tube for splits & security & airflow sensor. they will cause the engine to rev but no response (like a slipping clutch) so its manual right?

Oct 09, 2012 | 2008 Hyundai Accent

1 Answer

1994 gmc sierra pickup 4.3L V6 automatic transmission experiencing difficulties with ODrive = 4th gear, and Drive = 3rd gear, engine revs up to the max properties with little to no forward motion. Rev


You have internal transmission damage I expect the clutches on third and fourth gear are wiped out. Its either that or a solenoid gone bad that holds those clutches pressure get it in a transmission shop soon to avoid whole transmission replacement costs.

Mar 19, 2012 | Cars & Trucks

1 Answer

Out of nowhere my tranny started having this problem. I can put it in reverse and back up fine. But when i go to put it in drive it engages and inches forward but when i go to press the gas pedal it just...


CHECK FLUID LEVEL MAKE SURE ITS CORRECT AND FLUID AND FILTER HAS BEEN CHANGED IF ALL IS GOOD. SOUND LIKE THE FORWARD CLUTCH HAS WORN BURNED CLUTCH PLATES OR ROLLER CLUTCH HAS DAMAGED ROLLERS MISSING SPRINGS.CHECK TRANSMISSION PUMP OIL PRESSURE FOR A STUCK PRESSURE REGULATOR.

Aug 30, 2010 | 1995 Chevrolet Camaro

2 Answers

Is clutch adjustable? Engine revs,but barely moves


it's not if you have hydraulic system.
check to see if the clutch pedal is firm and has pressure
start your engine, depress the clutch pedal and put it in gear
if it goes in gear easily and the car won't move then you need clutch

Apr 21, 2010 | 1996 Ford Explorer

Not finding what you are looking for?
1990 Toyota 4Runner Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...