Question about Ford Edge
You can not delete your factory code from the system. Turn car off completely and start it back up. Go back to settings/vehicle/keyless entry pad and re enter the factory code it will work.
Posted on Jun 17, 2018
I had the same issue on my 2013 Edge. Deleted the password expecting it to let me enter a new one. Since the password is unique to vehicle and not able to be deleted I went into the SYNC computer settings and reset to original settings. This takes a minute. The screen goes black. Opening the door or turning key off is not suggested. Resetting the in dash computer(sync) is the fix for deleting the original door key code.
Posted on Oct 05, 2013
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
Yes you can program your own code by inputting the original code then hit the no. 2 button then input your own 5 digit code.
Posted on Mar 16, 2009
Every car different, call an auto rescue or towing company, the trucks are usually equiped with slim jims, that can be used to gain access to your vehicle.
Hope this helps.
Posted on May 05, 2009
Code p1131 manufacturer control fuel air metering, on a 2003 Ford Taurus. Where is part? Is there an easy way to see if it can be fixed without buying the expensive part?
Posted on Sep 01, 2009
SOURCE: Need to reprogram key less entry
Keyless Entry Keypad FAQ Ford Explorer
The keypad can be operated with the factory set 5-digit entry code
You can use the keyless entry keypad to
Where the code can be found
Computer Module location
Programming a personal entry code The factory set code cannot be reprogrammed but you can create your own 5�digit personal entry code. When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.
Up to three personal entry codes may be programmed to the vehicle. To create your own personal entry code:
Erasing personal code
Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash.
The anti-scan feature will turn off after
Unlocking and locking the doors, liftgate and liftgate window using keyless entry
Before following the activation or deactivation procedures, make sure that the anti-theft system is not armed, ignition is in the 1 (OFF/LOCK)position, and all vehicle doors, liftgate and liftgate window are closed.
*Keyless entry key pad procedure
Autounlock The autounlock feature will unlock all the doors when: � the ignition is in the 3 (ON) position, all the doors are closed, and the vehicle has been in motion at a speed greater than 12 mph (20 km/h); � the vehicle has then come to a stop and the ignition is turned to the 1 (OFF/LOCK) or 2 (ACC) position; and � the driver door is opened within 10 minutes of the ignition being transitioned to the 1 (OFF/LOCK) or 2 (ACC) position.
Note: The doors will not autounlock if the vehicle has been electronically locked before the driver door is opened.
Deactivating/activating autounlock - Keyless entry key pad procedure Your vehicle comes with the autounlock feature activated.
The keyless entry touch pad can use two codes. The factory code and one
personal code .
To program your own personal code, select a 5 digit code that doesn't use 5 digits in
sequence or the same button 5 times.
Enter your factory code
Within 5 seconds press the 1/2 button
Within 5 seconds of pressing the 1/2 button, enter your 5 digit personal code,
pressing each digit within 5 seconds of the previous digit.
You can now use either code to operate the keypad
Setting FOB to work with your vehicle
Posted on Sep 16, 2009
You have to reprogramm
the ECM. Here is a bulletin for this problem.
Service Engine Soon Light On, P1680 (Reprogram or Replace PCM)
2004 Buick Rainier
2004 Chevrolet Trailblazer
2004 GMC Envoy
2004 Oldsmobile Bravada
with 4.2L Engine (VIN S - RPO LL8)
Some customers may comment on the Service Engine Soon Light coming on. Upon investigation, the technician may find a P1680 diagnostic trouble codeCheck the resistance of the accelerator pedal position sensors using the procedure in the appropriate Service Information for DTC P1680.
If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built prior to the following VIN breakpoints, then reprogram the PCM with the latest calibration.
If the resistance of the accelerator pedal position sensor is within the specifications shown in the Service Information and the vehicle was built after the following VIN breakpoints, then replace the PCM. If the resistance of the accelerator pedal position sensor is outside the specifications shown in the Service Information, then continue with the diagnostics for DTC P1680.
• Vehicles built at Oklahoma City Assembly Plant - 46192755
• Vehicles built at Moraine Assembly Plant - 42315833
Hope help with this (remember rated this).
Posted on Jul 09, 2010
Tips for a great answer:
Dec 30, 2013 | 1993 Mercury Grand Marquis
Mar 18, 2013 | 2011 Ford Escape
Jun 21, 2012 | 2011 Ford Escape
Jun 04, 2011 | 2011 Ford Edge
May 12, 2011 | 2003 Ford Expedition
Jan 31, 2011 | Ford F-250 Cars & Trucks
May 03, 2010 | 1996 Ford Explorer
Nov 25, 2009 | 2004 Lincoln Navigator
Mar 16, 2009 | 2007 Ford Edge SEL Plus
991 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: