Question about 2008 Honda Ridgeline

Open Question

Replace wiper blades, driver side. I have a new rubber blade from dealer.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

shanat
  • 359 Answers

SOURCE: How do you change the rear wiper blade on the 2005 Honda Pilot?

hi at one end of the blade depress the clip and it should slide out when fitting the new one make sure you insert it into the runners evenly also i think u would break the blade before anything else so dont be affraid its the old one anyway

Posted on Jun 04, 2008

  • 1 Answer

SOURCE: How to replace Saturn wiper blades

The easiest way I do it is go to an national chain auto parts supplier like Discount Auto Parts or Auto Zone. They will select the correct blades and will put your wiper blades on for free. Take it from me after cracking my windshield once this is how I do it.

Posted on Nov 15, 2008

  • 1 Answer

SOURCE: 2005 Chevy Equinox Wiper blade hits edge of window

they are different size wiper blades. I just replaced mine in my 2005 chevy equinox. Passenger side is shorter.

Posted on Feb 23, 2009

c17hydro
  • 2984 Answers

SOURCE: How to remove and replace the wiper blades on a 2006 BMW 325i.

My suggestion....go to Schuck's/Kragen?Chief's?Auto Zone....they will install them for FREE.

Posted on Mar 11, 2009

  • 1 Answer

SOURCE: Replacing rear wiper blade

I purchased a Trico "Exact Fit" #12-A rear wiper blade at Advance Auto Parts for my 2006 RAV4. The directions are very clear. It took about 3 minutes. The key is to open the plastic cover at the bottom joint of the blade by spreading the both sides with your index fingers and pulling straight out. This opens the cover and allows you to bring the blade to a 90 degree angle.

Posted on Sep 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 Subaru outback driver side windshield wiper goes to far to the outside tears up the end of the blade - ideas please


I have the same problem with a 2001 Legacy wagon. The problem is not as simple as the solutions above. Mine are adjusted to park as low as possible when off. Even so, the blade on the drivers side goes all the way off the windshield. The Subaru dealer wants to replace the whole wiper blade transmission for about $450. Looking online it seems to be interconnecting arms and pivot points that connect the motor to the wiper blade arms.

Nov 17, 2011 | 2001 Subaru Outback

1 Answer

2000 BUICK REGAL MY WIPER BLADES (DRIVER SIDE) WENT OFF THE WINDSHIELD THE OTHER NIGHT. WHEN I PUT IT BACK IT DID NOT WORK PROPERTY WHAT COULD BE WRONG DO I NEED TO TAKE IT TO A DEALER?


i`m not sure what you mean by it not working properly i assume that you mean it goes back and forth like the passenger side, but it doesn`t clean the window and you put the blade on the arm correctly then the wiper may be damaged and you will have to replace the wiper blade.check and compare the installation of the driver`s side to the passenger side wiper and correct the installation of the blade

Mar 08, 2011 | 1999 Buick Century

1 Answer

The rear window wiper blade holder is rusted how do I remove it for replacement?


Three things you can replace depend on your budet
1) you can replace whole wiper blabe assembly by lift up the cover at the bottom end of the bale assembly and un-screw the nut and raplace whole assembly with arm , wiper insert etc ... with the new one This way cost you more.
2) on hte middle of the whole wiper blade assy has the flexible section, you can un-screw 2 small philipe pan head screw with screw driver and disconnect the top section with the wiper blade insert (rubber)
3) slide wiper blade insert out of the holder, becareful with 2 small steel blade will hole your rubber insert inside the wiper frame. Slide new rubber insert in the frame .

Feb 25, 2011 | 1995 Toyota Supra

1 Answer

I need to have 'step-by-step' instructions for replacing the driver side windshield wiper arm on my 2000 Ford Explorer. Can you help me with this?


  • Turn your wipers off, using the stalk on the left side of your steering column. Turn your ignition off and remove the key.

  • 2

    Pull the wiper blade up to lift it to the service position. Pull the front part of the blade down to position it at an angle.

  • 3

    Pull back the lock pin on the center part of the wiper blade (where it connects to the wiper arm). This unlocks the blade from the wiper arm.

  • 4

    Grasp the blade on each side and pull it down (away from the extended wiper arm) to release it from the "U" clip.

  • 5

    Repeat the process for the other wiper blade, if desired. Removing the driver's side and passenger's side wiper blade is the same.

  • 6

    Install the new wiper blade. Open the lock pin on the new blade, and then insert it into the wiper arm "U" clip. Close the lock pin and lower the wiper blade to its normal position.

  • Jan 29, 2011 | Ford Explorer Cars & Trucks

    2 Answers

    How to change the rubber on wiper blade of 06 corolla


    My advice is to forget changing the rubber. Just buy a complete wiper blade minus the arm. This way although you will spend a little more but avoid the hassle and get an entirely new blade. If you buy a quality blade you will only need to replace it once a year or every other year if the car is kept in a garage. I have been using the Rain X Latitude wiper blade and have found it to be a fantastic blade. After 1 year of use it is as good as the day it was installed. Most blades especially rubber blades start to deteriorate after 6 months. Whatever you buy make sure it is made of silicone and not rubber.

    Dec 10, 2009 | 2006 Toyota Corolla

    2 Answers

    Wipers freeze all winter, won't clean the window, have replace the blades 3 times still have the problem


    try a different wiper solution one thats a cleaner antifreeze to not just a cleaner

    Dec 10, 2009 | 2005 Ford Taurus

    1 Answer

    How to replace the wiper insert at the back of


    moz-screenshot.jpg
    1. REMOVE RR WIPER BLADE
      1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
      2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

    1. REMOVE REAR WIPER RUBBER
      1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
    f54b10a.gif
    1. INSTALL REAR WIPER RUBBER
      1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
    0dd144d.gif
    b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
    8f40009.gif
    c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

    Sep 12, 2009 | 2005 Toyota Matrix

    1 Answer

    Driver side wiper blade doesn't sync with passenger side blade


    the wiper arm assembly is stripped for the knurled knob that is sits on.  replace the wiper arm with a new one.

    Mar 30, 2009 | 1995 Geo Prizm

    1 Answer

    Don't know how to replace the wiper blade for honda accord, 1997


    hi from uk have come up against this problem on hondas and if you wish ? you can replace the wiper rubbers as i have done by going to halfords or other motor supermart and purchase the rubber/blades either same length or longer ? then remove the steel blades from each side of the rubbers on wipers by pulling from bottom whilst flexing the wiper clear ok? then pull out the rubberblade with patience you can easily feed new rubber into w/blade /make sure you insert right way ie there is a notch in rubber that goes to top look carefully ? then re fit steel blades one at a time into grooves in rubber making sure the top locates into notch in rubber job done ! and huge saving on having to buy complete arms and blade in uk rubbers approx £4 a pair ps if you get the longer rubber you can cut to same size as old b4 fitting hope this helps ?

    Jan 01, 2009 | Honda Accord Cars & Trucks

    1 Answer

    Rear wiper blade


    I went to a Honda dealer and bought a replacement wiper blade (rubber part only) for about $6, and the guy in parts came outside and changed it for me. You slip off the rubber blade only from the wiper assembly and then slip in the new blade.

    Jun 06, 2008 | 2003 Honda Pilot

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    72 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Honda Experts

    yadayada
    yadayada

    Level 3 Expert

    74945 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7697 Answers

    Are you a Honda Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...