Question about Nissan Pathfinder

1 Answer

Needing to replace water pump. Do you have to take off the cambelt and front pulley?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 66 Answers

Not sure what car you have, but probably, the belt your refering to is the timing belt, it keeps the crankshaft

Posted on Apr 11, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How will I know when a water pump is getting damaged


Normally a water pump leaks when the bushings wear out or are damaged, other than that check the temp gauge.

Nov 09, 2013 | 2005 Renault Megane 1.6

1 Answer

Remove and replace the water pump buick rendezvou 2003 cost and do it yourself instructions . can i do it myself concerned with loosening the serpentine belt and needing special tools?


1. Drain the cooling system until the coolant is below the level of the water pump. 2. Remove the drive belt guard. 3. Loosen the water pump pulley bolts. 4. Remove the drive belt. 5. Remove the water pump pulley bolts. 6. Remove the water pump pulley. 7. Remove the water pump bolts. 8. Remove the water pump. 9. Remove the water pump gasket. 10. Clean the water pump mating surfaces. Installation Procedure 1. Install the water pump gasket. 2. Install the water pump Notice: Refer to Fastener Notice in Service Precautions. 3. Install the water pump bolts. Tighten the bolts to 10 Nm (89 inch lbs.). 4. Install the water pump pulley. 5. Install the water pump pulley bolts. 6. Install the drive belt. Tighten the water pump pulley bolts to 25 Nm (18 inch lbs.). 7. Install the drive belt guard. 8. Fill the cooling system
Visit my Blog here

Jul 21, 2010 | 2002 Buick Rendezvous

1 Answer

WHERE IS THE WATER PUMP LOCATED...2003 ELANTRA


hi from uk fortunately the water pump on your car is not driven by cambelt ! the pump is driven by serp belt the pumps location is = if you look at front of engine view from front wing as you look down front you will see a large pully on left of cambelt covers and this is the water pump access to pump is best by supporting car and removing wheel and then the under wing cover that is secured by screws some advice for you if you intend renewing pump the pump pully is secured by 4 bolts use a 10 mm cranked ring spanner or socket loosen these bolts before you remove the drivebelt as belt holds pully and helps to prevent pully turning as you try to loosen these bolts hope this helps ?

Jan 26, 2010 | Hyundai Motor 2003 Elantra

1 Answer

Were is the water pump on a citreon dispatch


cambelt. it leaks at the back of the pulley o/s wheel.

May 11, 2009 | 1998 Ford Aerostar

2 Answers

TIMING MARKS CAMBELT REPLACEMENT FOR CL-T CHARADE, PLEASE


This is the best I could find for you .. I am unfortunately able to verify the info because I have no personal experience with this car or its engine ...

Mar 14, 2009 | 1988 Daihatsu Charade

1 Answer

Replace water pump


its run by the cambelt and will be behind the timing covers.will invovlve removing cambelt to replace

Feb 24, 2009 | 1995 Audi A6

1 Answer

2002 Audi A4 - replace cambelt


DRILL OUT THE OLD BOLTS FIT NEW ONES ONTO YOUR OLD PULLEY/VIBRATION DAMPENER...EASY...ONLY PAY FOR THE TIME TO DRILL OUT BOLTS NOT NEW PULLEY

Jul 30, 2008 | 2002 Audi A4

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...