Question about 1998 GMC Suburban

1 Answer

How do I remove and replace the bulb (Part #168) in reading lamps in 1998 Suburban Page 2-43 of owner's manual describes the function but does not provide advice on how to remove the bulb.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 57 Answers

If i was you i would just use CRC or WD40

Posted on Apr 11, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change brake light bulb on a 2014 fiat 500L


https://www.fiatusa.com/download/pdf/manuals/2014-FIAT-500L-OM-1st.pdf

it's in your owners manual page 358 chapter 7

you need a torx 20 screwdriver or bit

Rear Tail, Stop, Backup And Turn Signal Lamps
1. Open the liftgate.
2. Remove the two screws and remove the tail lamp assembly.
3. Remove the four screws (using a T20 driver) and separate the backplate from the lamp housing.
4. Remove the tail, stop, or turn signal bulbs by pushing them slightly and turning counter-clockwise.
5. Remove the backup lamp bulb by pulling straight out.
6. Replace lamps as required and reinstall lamp.

Center High-Mounted Stop Lamp (CHMSL)
This light is an LED assembly. See your authorized stealership

Mar 30, 2015 | Fiat Cars & Trucks

1 Answer

How do I change the inside headlamps on my 1998 Suburban?


It depends, if you have sealed beam headlamps, there should be a frame around headlamp, remove it.
If composite headlamps, there are two hex headed pins in top radiator support, remove those pins. Take out lamp assembly so you can get at bulbs.Don't touch new bulbs with bare hands.

Dec 17, 2014 | 1998 GMC Suburban

2 Answers

How do i replace head lamp on kizashi?


the bulb or the the whole housing/????????
read the manual at
$4

https://suzukipitstopplus.com/Products/10243-2011-kizashi-service-manual.aspx

the glove box.
open the door
extract the oper guide
turn to head light page, bingo?

Sep 02, 2014 | 2011 Suzuki Kizashi

1 Answer

Need to change out a broken tail light cover for a 2002 mercury sable


Replacing tail/brake/turn signal/backup lamp bulbs (page 59-60 of owners manual)

Sedan

The tail lamp, brake lamp, turn

signal lamp and backup lamp bulbs

are located in the same portion of

the tail lamp assembly. Follow the

same steps to replace either bulb.

1. Make sure headlamp switch is in

OFF position and open trunk and

remove two plastic mushroom nuts,

three push pins and the plastic

cover from inside the trunk to

access the lamp assembly.

2. Carefully pull the carpet away to

expose the lamp assembly hardware.

3. Remove four nut and washer

assemblies and the lamp assembly

from the vehicle.

4. Remove the bulb socket by

rotating it counterclockwise, then

pulling it out of the lamp assembly.

5. Pull the bulb from the socket and
push in the new bulb.

6. Install the bulb socket into the lamp assembly by rotating it clockwise.

7. Install the lamp assembly on the vehicle with four nut and washer

assemblies ensuring the washers on the nuts are flush with the body to

prevent water from entering the trunk.

8. Carefully push the carpet back in to place and install the plastic cover
inside the trunk with three push pins and two plastic mushroom nuts.

May 31, 2011 | Mercury Sable Cars & Trucks

1 Answer

Need part # for License Plate bulb.


i looked in my owners manuel it said the license plate lamp is bulb type 168 hope that helps

Nov 12, 2010 | 1998 Jeep Grand Cherokee

1 Answer

No revers lights


REMOVAL & INSTALLATION 1988–91 R/V Series
  1. Remove the lens-to-housing attaching screws. Remove the lens.
  2. Replace the bulb(s).
  3. Installation is the reverse of removal.
Except 1988–91 R/V Series Fig. 1: Remove the lamp assembly retaining screws 87986p17.jpg
Fig. 2: Pull the lamp assembly from the truck 87986p18.jpg
  1. Lower the tailgate.
  2. Remove the lamp assembly retaining screws.
  3. Pull the lamp assembly from the truck and disconnect the wiring.
  4. Remove the bulb holder fasteners.
  5. Remove the bulb(s) from the lamp.
  6. Install the bulb, connect the wiring and install the lamp. Fig. 3: Disengage the electrical connection 87986p19.jpg
    Fig. 4: Unfasten the bulb holder retainers 87986p20.jpg
    Fig. 5: Remove the bulb holder 87986p21.jpg
    Fig. 6: Pull this type of bulb from the socket 87986p22.jpg
prev.gif next.gif

Sep 03, 2010 | 1994 Chevrolet Suburban

1 Answer

I want to replace the headlight and the owners


It's talking about the headlamp bezel, the bezel is a band that goes around the parimeter of the lamps and holds it in the "headlight bucket". The screws may be a T15 Torx, if it looks like an allen head but an allen won't fit try a Torx driver.

May 27, 2010 | 1998 Chevrolet Suburban

1 Answer

My license plate lights are out...what kind of bulbs do i need??


Check this reference guide...

2002 Hyundai Accent Car Lightbulb Size Guide
Low Beam Headlight Bulb Size: 9003/HB2
High Beam Headlamp Light Bulb Size: 9003/HB2
Parking Light Bulb Size: 2357A
Front Turn Signal Light Bulb Size: 2357A
Rear Turn Signal Light Bulb Size: 1156
Tail Light Bulb Size: 1157
Stop Light Bulb Size: 1157
High Mount Stop Light Bulb Size: 921
License Plate Light Bulb Size: 168
Back Up Light Bulb Size: 1156
Front Side Marker Light Bulb Size: 2357A
Rear Sidemarker Light Bulb Size: 168
Map Light Bulb Size: DE3175
Dome Light Bulb Size: DE3175
Step/Courtesy Light Bulb Size: DE3022
Trunk/Cargo Area Light Bulb Size: DE3022

From Sylvania Lamp Replacement Guide
License plate
168
168LL Long Life Upgrade: Up to twice the life of the standard lamp.


I hope help you with this. Good luck (remember rated this help).


Sep 09, 2009 | 2002 Hyundai Accent

1 Answer

License Plate lamp burned out.


you'll see the lights plugged in under rear bmper. grasp the light plug,twist counter clkwise 1/4 turn, pull out plug, pull bulb strait out, push new bulb back in.

Nov 11, 2008 | 1998 GMC Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

61 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...