Question about Audi 90

1 Answer

This is my 3rd time replacing strut mounts for this audi struts never seems to be tight or tighten down always a gap must be the wrong size or their is a part missing please help is their a special strut mount for this model.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 184 Answers

Some audi models have a gap as you jack the wheel off the ground,the shaft coming through top mount falls down considerably.But there should be no side play.This catches out many test stations,unless they refer to their service buletins.Hope this helps you,supply the model and I can confirm this.

Posted on Apr 11, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I remove struts on my 1996 Lincoln continental?


Try "autozone.com" or your local library for diagrams and step by step instructions.

Aug 31, 2014 | Cars & Trucks

1 Answer

How to remove and replace front air suspension struts in 2006 Audi A8


Follow these steps:
  1. Open the car hood. If you have a factory stereo system installed you need to now the security code t reactivate the sound. Remove the negative cable from the battery to prevent the air bags from popping.
  2. Use a pair of wheel chocks behind the rear wheels. Use a car jack to raise the side of the car you will work on. Take off the wheel by loosening the lug nuts.
  3. On the wheels wells in the engine chamber use a socket and ratchet and remove the grommets and upper strut nuts. Also disconnect the brake hose bracket and ABS sensor wire from under the car.
  4. Again take the socket and ratchet to loosen the pinch bolt and nut located on the upper control arm, which you will remove from the wheel knuckle. When the pinch bolt goes through you must not pry open the slotted area. Use a socket and ratchet and remove the strut assembly.
  5. Place a spring compressor on the coil spring and tighten it enough to relieve the pressure from the spring cap. Using a socket and ratchet remove the center nut from the strut rod. Remove the spring cap, coil spring and spring seats from the strut. Place the coil spring on the new strut along with the new spring seats and spring cap.
  6. Place the center nut on the strut rod and tighten it. Take off the spring compressor form the coil spring. Install the strut on the Audi and mount the upper control arm with the wheel knuckle.
  7. Connect the ABS sensor wire to the strut. Attach the brake hose bracket to the strut and tighten the nut. Install the three upper strut nuts in the engine compartment and tighten them. Cover the nuts with grommets. Place the wheel on the Audi and tighten the lug nuts with the lug wrench.

Mar 17, 2014 | Cars & Trucks

1 Answer

How do you replace front broken coil spring on 1998 ford windstar? do you have a diagram, pictures or video?


Strut and Spring Assembly Removal
  1. Raise the vehicle on a hoist.
  1. Remove the front wheel and tire assembly.
  1. ani_caut.gif CAUTION: To avoid damage to the 6mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten to final torque the front stabilizer bar link-to-front shock absorber nut.
    Remove the stabilizer bar link retaining nut and disconnect the link from the strut.


f8740a.gif

  1. ani_caut.gif CAUTION: Do not allow the halfshaft to move outboard. Over extension of the CV joint may result in the separation of internal parts, causing failure of the joint.
    Remove the strut assembly-to-steering knuckle pinch bolt. If required, slightly spread the steering knuckle to ease the removal of the strut. Pry down on the lower control arm and roll the strut base out of the knuckle. Do not pry on the halfshaft, as damage may result. Wire the steering knuckle up to prevent the halfshaft from moving outboard.
  1. Partially lower the vehicle.
  1. Support the strut assembly and remove the top three mount-to-strut tower nuts. Remove the strut assembly from the vehicle.


f9154a.gif

  1. ani_caut.gif CAUTION: The strut assembly is under spring tension. Attempting to disassemble the strut without properly compressing the spring can result in injury.
    Using a suitable spring compressing tool, slightly compress the strut spring to relieve initial tension. Loosen the upper rod nut. Continue to compress the spring until the tension is relieved. Remove the upper rod nut.


f3897c.gif

  1. Remove all upper mounting parts, coil spring, and coil spring isolators from the strut and save them for reassembly. Carefully note the position of each part during removal to ensure proper reassembly. Inspect each part for wear and damage as it is removed.
Installation
  1. ani_caut.gif CAUTION: The bearing and seal assembly is press-fit onto the upper mount. The mount washers must be installed in the correct orientation.
    NOTE: Be sure to check the spring insulator for damage before assembly. If the outer metal splash shield is bent or damaged, it must be carefully bent back, so it does not touch the locator on the bearing and seal assembly.

    NOTE: New gas struts are shipped with the rod in a locked down position. To extend the new strut, remove the external tie down and/or rotate the upper end of the rod, counterclockwise.

    Install the coil spring insulator, coil spring, and upper mounting parts to the new strut assembly. Make sure the spring is correctly seated in both spring seats.


f8737a.gif


Item Part Number Description 1 ? Dust Boot (Part of 18045) 2 N803826-S100 Front Shock Absorber Mounting Bracket Nut
(3 Req'd) 3 N803952-S100 Washer 4 N808625-S100 Front Shock Absorber Nut 5 18183 Front Shock Absorber Mounting Bracket 6 3B455 Front Suspension Bearing and Seal 7 5310 Front Coil Spring 8 5414 Front Spring Insulator 9 18045 Front Shock Absorber A ? Tighten to 35-40 Nm
(25-30 Lb-Ft) B ? Tighten to 55-63 Nm
(40-46 Lb-Ft)
  1. ani_caut.gif CAUTION: Do not over tighten the lock nut; damage to the lock nut or piston rod could result.
    Install new rod lock nut and tighten it to 55-63 Nm (40-46 lb-ft).


f3897c.gif

  1. Remove the spring compressing tool.
  1. Position the strut assembly into the vehicle. Install the three mount-to-strut tower nuts. Tighten the nuts to 35-40 Nm (25-30 lb-ft).


f9154a.gif

  1. Partially raise the hoist.
  1. Position the strut assembly to the steering knuckle. Install the pinch bolt and tighten it to 115-132 Nm (85-97 lb-ft).
  1. Position the stabilizer link to the strut assembly and install the retaining nut. Tighten the nut to 90-100 Nm (66-74 lb-ft).


f8740a.gif

  1. Install the front wheel and tire assembly.
  1. Lower the vehicle.
hope this helps

Aug 14, 2011 | 1998 Ford Windstar

1 Answer

How to replace the shocks on my 2000 Mazda 626


REMOVE**** FRONT SHOCKS, FIRST OF ALL.SUPPORT THE LOWER CONTROL ARM WITH A JACK,REMOVE FRONT WHEEL, REMOVE BRAKE HOSE AND ABS SENSOR HARNESS TO THE STRUT BOLTS OR CLIPS,REMOVE ACTUATOR FROM TOP OF THE STRUT,IF EQUIPPED WITH AUTOMATIC ADJUSTING SUSPENSION. PAINT ALIGNMENT MARKS ON THE UPPER STRUT MOUNTING BLOCK AND STRUT TOWER AND ON THE LOWER STRUT MOUNT TO STEERING KNUCKLE SO THAT CAN BE REINSTALLED IN THE SAME POSITION. REMOVE UPPER STRUT MOUNTING NUTS, REMOVE THE STRUT TO KNUCKLE BOLTS,REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT INTO THE STRUT TOWER ALIGNING THE PAINT MARKS MADE DURING REMOVAL.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 34 - 46 FT LBS. INSTALL STRUT TO KNUCKLE BOLTS TIGHTEN TO 55 - 61 FT LBS. INSTALL ACTUATOR AND ENGAGE THE ELECTRICAL CONNECTOR IF EQUIPPED WITH AAS. INSTALL BRAKE HOSE AND ABS SENSOR HARNESS CLIPS OR BOLTS.INSTALL WHEEL AND CHECK ADJUST THE FRONT END ALIGNMENT. TO ( REPLACE REAR SHOCKS ) REMOVE REAR WHEELS, REMOVE REAR PACKAGE TRIM. REMOVE SPEED SENSOR HARNESS, REMOVE TOP STRUT NUTS,THE SUSPENSION WILL DROP WHEN THE WEIGHT LIFTS OFF THE WHEELS. REMOVE BOTTOM STRUT BOLTS.REMOVE STRUT ASSEMBLY.TO INSTALL ***** INSTALL STRUT ASSEMBLY, INSTALL BOTTOM STRUT MOUNT BOLTS AND TIGHTEN TO 55 - 61 FT LBS.INSTALL UPPER MOUNTING NUTS AND TIGHTEN TO 33 - 46 FT LBS. INSTALL SPEED SENSOR HARNESS.INSTALL REAR PACKAGE TRIM. INSTALL REAR WHEELS.

Sep 22, 2010 | Mazda 626 Cars & Trucks

2 Answers

How to change front struts toyota echo


  • remove wheel
  • undo top and bottom strut bolts...3 in the engine bay and two at the wheel end.
  • remove strut

Sep 10, 2010 | 2001 Toyota Echo

1 Answer

Strut issue on volkwagen cabrio


replace strut bushings and strut and shouldn't be tightened over 20 ft lbs.

Jul 02, 2009 | 1999 Volkswagen Cabrio

1 Answer

Removed old strut last night Today can't get new


Installation
  1. sww~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The bearing and seal assembly is press-fit onto the upper mount. The mount washers must be installed in the correct orientation.
    NOTE: Be sure to check the spring insulator for damage before assembly. If the outer metal splash shield is bent or damaged, it must be carefully bent back, so it does not touch the locator on the bearing and seal assembly.

    NOTE: New gas struts are shipped with the rod in a locked down position. To extend the new strut, remove the external tie down and/or rotate the upper end of the rod, counterclockwise.

    Install the coil spring insulator, coil spring, and upper mounting parts to the new strut assembly. Make sure the spring is correctly seated in both spring seats.


a1048fe.gif


Item Part Number Description 1 — Dust Boot (Part of 18045) 2 N803826-S100 Front Shock Absorber Mounting Bracket Nut
(3 Req'd) 3 N803952-S100 Washer 4 N808625-S100 Front Shock Absorber Nut 5 18183 Front Shock Absorber Mounting Bracket 6 3B455 Front Suspension Bearing and Seal 7 5310 Front Coil Spring 8 5414 Front Spring Insulator 9 18045 Front Shock Absorber A — Tighten to 35-40 Nm
(25-30 Lb-Ft) B — Tighten to 55-63 Nm
(40-46 Lb-Ft)
  1. sww~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not over tighten the lock nut; damage to the lock nut or piston rod could result.
    Install new rod lock nut and tighten it to 55-63 Nm (40-46 lb-ft).




  1. Remove the spring compressing tool.
  1. Position the strut assembly into the vehicle. Install the three mount-to-strut tower nuts. Tighten the nuts to 35-40 Nm (25-30 lb-ft).




  1. Partially raise the hoist.
  1. Position the strut assembly to the steering knuckle. Install the pinch bolt and tighten it to 115-132 Nm (85-97 lb-ft).
  1. Position the stabilizer link to the strut assembly and install the retaining nut. Tighten the nut to 90-100 Nm (66-74 lb-ft).




  1. Install the front wheel and tire assembly.
  1. Lower the vehicle.

May 01, 2009 | 1998 Ford Windstar

2 Answers

Replace rear struts 1996 buick regal


Here is a link describing your strut replacement. Autozone also has free tool rental for the strut spring compressor if you need it. Thank you, and don't forget to vote. http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800681ba

Jan 29, 2009 | 1999 Buick Regal

1 Answer

87 Audi Coupe - Clunking Noise


the car is aging

there are other bushings and ball joints to make noises at that speed

the top rubber mounts failed for a reason

if i were on that job i would have replaced both gas struts
at the same time....

not much structure to the top strut mounts
see pictures in link
Strut Mount Early Small Chassis Audi Density Line





sus-r0fvbv0fnqz1bkfnyk2eh2wx-2-0.jpg

index-r0fvbv0fnqz1bkfnyk2eh2wx-2-1.jpg

Mar 08, 2017 | 1987 Audi GT

1 Answer

Busted drivers side spring. howdo you remove it safely


coil spring:
buy/rent a spring compressor.
hook it upside down over the second last coils of the spring(second last coil of the unbroken part) (bolt heads down and accessible) so that the compressor clears the spring seats.
Use all parts of the compressor.
Do up the spring compressor till it is just tight.

Put the car up on a 2 post, as the load comes off the suspension the spring will tighten in the compressor and flop around loose on the strut. Unbolt the top strut mounts. lower the axle until there is clearance and lift the spring off the strut.
Slowly take the tension off the spring compressor
Put the new spring in the spring compressor, (second last coils to clear the spring seats when reinstalling).
tighten the spring compressor, evenly and compress the spring, till it fits over the strut.
lift the axle, bolt on the top strut mounts, slowly release spring compressor, ensure top n bottom spring coils seat in the spring seats.
lower two post hoist
test drive

Always replace springs together as a pair

Jul 29, 2008 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14200 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...