Question about 1994 Toyota Corolla

1 Answer

I installed the timing belt and the car still has no current activity idk wats wrong with it

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 29 Answers

Make sure u installed all the parts right. It is critical that u get the timing right. If you messed up the timing while installing the new timing belt, you could cause internal damage if you try to start it up.

Posted on Apr 11, 2011


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 04 Camry and we'll all of a sudden it wants to just shut off but it putters for a little plz someone help me figure it out I'm so lost idk wat to do

Has the timing belt been replaced at the stated time listed in the drivers manual ?. I found that the belt has a habit of jumping a few teeth, when the belt has become worn , replace it if it has as , it will cause massive damage if it brakes. If it checks out ok , check the spark at the plugs . then fuel pressure and flow, a blocked fuel filter can cause the flow do drop and stop the engine from running.

Jun 17, 2015 | 2004 Toyota Camry

1 Answer

99 durango no power removed dash no power now maybe a short or wat

I think you may not have connected the main harness to the dash when you reinstalled it. The only way I know of to be sure is to pull dash again, this plug is not accesable with the dash installed.

Feb 02, 2014 | 1999 Dodge Durango

1 Answer

My truck is spitting and sputtering and does wanna go idk wats wrong with it

well i am a home mechanic and i suggest you just buy this manual, i bought it and it is completely amazing

and it sounds like a fuel filter or pump problem

Jan 05, 2011 | 1992 Ford Ranger

1 Answer

My timing belt went out and i fixed it and the valves and i put new spark plugs in and now it shakes idk wat 2 doo

The timing belt may have not been fitted to correct length or tightness or the engine mounts could have snapped, Have a look at all the engine mounts as if any are defective they will allow the engine to shake the body of the car.

Jul 08, 2010 | 2002 Daewoo Leganza

1 Answer

How to disable seatbelt alarm on 2003 F-150?

There is a procedure in the owners manual on page 110.

BeltMinder activation and deactivation procedure
1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE.)
2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes.)
• Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
3. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled. This can be done before or during BeltMinder warning activation.
4. Turn on the parklamps/headlamps, turn off the parklamps/headlamps.
5. Buckle then unbuckle the safety belt three times, ending with the safety belt unbuckled
• After step 5 the safety belt warning light will be turned on for three seconds.
6. Within seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt.
• This will disable BeltMinder if it is currently enabled, or enable BeltMinder if it is currently disabled.
7. Confirmation of disabling BeltMinder is provided by the safety belt warning light flashing four times per second for three seconds.
8. Confirmation of enabling BeltMinder is provided by:
• The safety belt warning light flashing four times per second for three seconds.
• Followed by three seconds with the safety belt warning light off.
• Once again, the safety belt warning light will flash four times per second for three seconds.
9. After receiving confirmation, the deactivation/activation procedure is complete.

If you did not get an owners manual with your truck ( purchased used ), you can download one from Ford :

Dec 20, 2009 | 2003 Ford F150 Regular Cab

1 Answer

Not starting

your cam to crank timing is wrong...recheck it.  Or your spark plug wires are in the wrong places

Mar 27, 2009 | 1993 GMC Jimmy

1 Answer

How to fix an 89 camaros rear wheel breaks so they will work?

try this sight. use the search button and there wil be a thread on this subject.

Mar 25, 2009 | 1989 Chevrolet C/K 3500

Not finding what you are looking for?
1994 Toyota Corolla Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8582 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides