Question about 1984 Toyota Camry

1 Answer

I have an 84 Toyota Camry, and the wheel studs sheared off, I got the old ones out, and to put the new ones in, you have to get the whole front of the car up so you can turn the spindle........anyway, after putting all the studs in each hole through the little slot underneath, I am wondering how you press them in there??? The only way I figured was to tighten them really tight, but normally I use a "C" clamp to do it. There is a plate behind them with no room, and you can't remove it. Let me know what I should do.......thanks.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 163 Answers

Ideally you're supposed to take the hub off the car and use a hydraulic press to press them into place.

Alternatively you can do a less then ideal method by taking a stack of large washers and placing them over the stud and tightening a lugnut down. As you tighten the lugnut it should drawn the new stud thru the spindle into place.

Posted on Apr 11, 2011

Testimonial: "Thanks, thats basically what I did, but wasn't sure if that would do it. Thumbs up......"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix 91 Mercury Sable Sedan right front wheel studs that have been sheared off?


tire shop or garage can press out damaged studs press in new studs.

Jun 17, 2013 | 1991 Mercury Sable

1 Answer

Ignition switch is broke


Here are procedures for removing the ignitionlock assy. If equipped with SRS, extra care must be taken while removing ang installing to avoid damage to the SRS cable reel.

IGNITION SWITCH & LOCK CYLINDER
Removal
1. Remove steering wheel and combination switch (if necessary). Disconnect ignition switch harness connectors. If shear bolt studs are accessible, use a hacksaw to cut slots into exposed studs.

2. Remove studs using a screwdriver. If shear bolt studs are recessed or hard to reach with hacksaw, use a center punch on studs. Using a drill bit and screw extractor, remove studs. Place key in ACC position and remove ignition switch and lock cylinder.

Installation

To install, reverse removal procedure. Install NEW shear bolts. Tighten shear bolts finger tight. Ensure proper operation of ignition switch and lock cylinder. Tighten shear bolts until heads break off. Install combination switch, upper and lower steering column covers and steering wheel (if removed). Tighten steering wheel nut and Torx screws to specification.

Sep 26, 2010 | 1996 Toyota Avalon

1 Answer

Broken wheel stud


Unless you hit a curb or something you have bumper to bumper warranty for 3yrs.36 k miles.If not then you can remove the wheel and brake caliper and rotor.Then pound the stud out with a hammer and reinstall the new one.Use a socket or some type of spacer and put on new stud once you have put the stud through the axle.Install the new nut on and start tightening til the stud is seated on the axle.Reinstall the wheel and torque to specs.Depending on type of wheel could be 80-100 ft.lbs.Hope this helps.Good luck.

Dec 23, 2009 | 2002 Pontiac Grand Am

1 Answer

Sheared off Wheel Stud


Not realy that critical sense theres 4 others, but it should be replaced as soon as posible. They put 5 on there for a reason.

Oct 06, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Sheared front lug


First remove wheel from car. Next take large hammer and drive whats left of lug out, you may need to use a punch if sheared off below hub hight. Now insert new lug stud in from back side of hub and use a open style lug nut (like those you see on old cars without nice wheels) and put on upside down, flat side towards hub. tighten up by hand then use socket to tighten down untill stud is pulled in all the way. In some cases you may need to use a few washes under nut to give enough room for shank on stud.

Sep 09, 2009 | 1993 Pontiac Sunbird

3 Answers

89 4x4 pu broken wheel stud


Half right...pound out, use a stack of washers and put nut on backwards and draw stud in. Oil on washers and stud threads helps.

Jun 19, 2009 | 1989 Toyota Pickup SR5

1 Answer

Snapped wheel studs on front wheels and need to change them


you have to hammer the studs through the spindle to get them out. then **** the new ones in with a nut and lots of washers. put grease on the washers and threads before you **** the studs in.

Apr 15, 2009 | 1988 Toyota Corolla 4 Door

1 Answer

How do i replace the front wheel studs on my hyundai accent


Hyundai in all their wisdom decided to use captive dust shields on the disc brakes. You need to completely disassemble the hub to get the shield off. On my 2008 Accent there is one spot that if you rotate the rotor to that spot and bend the shield back you can then get the stud in place. Be sure to get the right stud as the rear and front are probably different part numbers.

To get the old out use a hammer and a punch to pound them out the back. To get a new one in push it in as far as you can, then using something as a spacer (large nut or washers) and the wheel lug, tighten the stud up drawing it into the rotor.

Jan 08, 2009 | 2000 Hyundai Accent

1 Answer

1993 totoya camry v6- Changing the rotors


LOL!! Ya they are a pain in the a$$ if it's the year car I am thinking of. Are there 3 "threaded screw holes" near the wheel stud holes? If there is you need a special tool called a slide hammer to get the rotors off. You can get one of these on loan from Autozone for example. And may the force be with you.

If there is not, then you should jump up and down and be glad. Get some rust penetrant and a big hammer, like a 2 or 3 pound hammer. Put all lug nuts on all of the wheel studs (not tight just on a few turns with your fingers) to protect the threads when you are wacking at the rotor with the hammer. This will also keep the rotor from falling on you (they are pretty heavy). Spray the rust pentrant through the wheel stud holes and around the middle where the rotor meets the wheel hub and let it soak for about 5 minutes. Now firmly start wacking the rotor being careful not to hit the actual flat surface of the rotor but the very edge as well as the middle near the wheel studs.

A little cursing at it will improve your chances while you are hitting it. Been there, done that, got the T-Shirt!!

Good Luck!!

Sep 05, 2008 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...