Question about 1993 Dodge Spirit

2 Answers

I cant trun my motor over by hand to put my torque bolts in but it wont turn

Posted by Anonymous on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Speed odometeor not workiqng

Posted on Jun 13, 2011

  • Queenws1 Jun 13, 2011

    Speed odometeor not working I change the tran gear. And that did not work

×

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

I've used a big, flat screwdriver to turn converter a few teeth at a time. Or use a breaker bar and socket on the balancer on the front of motor. Hope this helps.

Posted on Apr 11, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove oil pan


jack it up, drain oil from drain plug on oil pan when drained remove and replace oil filter also. remove the pan bolts pull off pan and gasket.put new oil pan gasket on if needed.when oil pan bolts are back in, screw them in hand tight, then torque them down to specs and alter nate the tightening so it wont damage pan seal. any auto parts store can tell you the torque on the bolts for your car. good day!

Mar 31, 2014 | 1999 Chevrolet Venture

1 Answer

Why would a new motor in my 89 f-250 not turn over


make sure you have the torque converter deep enough in trans and can you turn engine over with strong arm and socket on crank bolt

Mar 28, 2013 | 1989 Ford F 250

1 Answer

Replace water pump torrent


drain coolant until below water pump level. loosen water pump pulley bolts.then remove drive belt by rotating belt tensioner.remove drive belt from the right of idler pulley.carefully release the drive belt tensioner spring tension.then remove water pump pulley bolts and pulley.remove water pump bolts and water pump pay attention to the position old water pump when removing water pump so you can line up new water pump holes to the engine. be sure clean engine water pump mounting surface use gasket remover dont scratch engine surface when cleaning removing old gasket material. take new water pump gasket get it mounting holes line up with new water pump mounting holes.when done getting engine water pump surface clean.water pump gasket paper you need to put thin layer of sealer on both sides of water pump gasket use RTV SILICONE.LET SET UP 10 MINUTES. PUT GASKET ON WATER PUMP BUT FIRST MAKE SURE LINE UP GASKET HOLES WITH WATER PUMP HOLES BEFORE PUTTING ON THE GASKET SEALER.when gasket sealer set up 10 minutes then install new water pump with gasket to the engine torque to 89 inch lbs.or 10 NM that is about 7 ft lbs torque.you should be able turn water pump by hand if you cant turn water pump by hand got too tight damage water pump shaft bearing.when all done wait for THREE HOURS. before adding coolant i let RTV CURE SOME. torque water pump pulley bolts 18 ft lbs.

Dec 28, 2012 | 2006 Pontiac Torrent

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

1 Answer

Torque converter ta


Torque converter is located in the bell houseing of the gear box (Automatic) You need to remove the inspection cover from the bottom of the bell houseing & it has several bolts attaching it to the flywheel (ring gear) of the engine. You will need to turn the motor by hand to get all those bolts. Then you have to remove the whole gearbox. then you can remove the converter from the bell houseing. MAKE SURE IGNITION IS OFF WHEN TURNING MOTOR BY HAND

Jun 16, 2012 | 1984 Chevrolet Chevy

1 Answer

Cant get the oil pan off a 302


You have to jack the engine up after removing the motor mount bolts on each side. Then once you have the engine jacked up a few inches, slide a piece of wood (2x4) in between the upper and lower parts of the motor mounts on each side. This will keep the engine elevated enough for you to drop the oil pan and replace the gasket. Then, just put all the bolts back in in the proper torque sequence, torque them all to spec,remove the wooden blocks from the motor mounts, slowly lower the engine back down and put the motor mount bolts back in.

Mar 16, 2011 | 1993 Ford F150 SuperCab

1 Answer

I need the torque specs for my valve covers on my 1990 bronco 2 v-6


No torque specs. Don't use sealer, that can cause the gasket to slip. Put cover in place, start all bolts, loosely snug all, hand tighten from bottom two, top two, bottom ends, top ends. Warm up motor and re-tighten (good hand snug) do not over tighten.

Oct 19, 2010 | 1990 Ford Bronco

2 Answers

Rod wont allow pump to go in. How do i get the rod up to allow fuel pump access. It is on an 82 Ford F150.


Which engine? Not knowing that, you may need to turn engine over to get the cam up, there will be some tension to start the bolts in.

Nov 05, 2009 | 1982 Ford F 150

2 Answers

Torque converter removal


is it front wheel or rear? if front you have to take down the motor and trans together by unbolting the 4-6 very large bolts and drop the entire front assembly.
if rear drive disconnect the drive shaft and unbolt the crossmember get a trans jack or one with wheels that work and unbolt trans from motor.
remember to SPIN the torque con when reinstalling.

May 20, 2009 | 1998 Pontiac Trans

1 Answer

Tranny/motor connectivity


there is a nipple on the converter that must meet up with a indent in the middle of the flywheel you need to have some help and one of you spin the torque converter and gently rock the moter in to place it will worki have done this several times on the rangers 

May 14, 2009 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
1993 Dodge Spirit Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...