Question about 2001 Toyota Celica

1 Answer

Engine too lean code po171 bank 1 (actually two codes-both the same thing)

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,915 Answers

Almost always caused by a vacuum leak, look for a damaged hose, or one that has become disconnected. It can also be caused by a leaking intake gasket or a leaking exhaust manifold before the O2 sensor.

Posted on Apr 11, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bank 1 system too lean code po171 how to repair


code p 0171 refers to system too lean bank 1===causes --intake/exhaust leak---AIR system---MAF/VAF sensor---fuel pressure/ pump/ pressure regulator---injector/s---heated oxygen sensor (HO2S unit in the exhaust manifold or before the cat converter
If the engine is running well then consider replacing the HO2S unit as that reports to the ECM that then adjusts the mixture for that bank by altering injector amounts and timing
all the rest affect both banks but the code is bank 1 specific

Sep 18, 2016 | Cars & Trucks

1 Answer

Po171 po174 code


Lean bank 1 and bank 2 , and throttle actuator system fault. Check reason for lean codes 1st, vacuum leak(s), air inlet boot and hoses, or low fuel pressure / clogged filter. Repair as needed then clear codes and recheck .

Jan 09, 2014 | Cars & Trucks

1 Answer

1998 Ford Contour 2.5 litre, 30,000 km. Started cold after sitting for a day in -20C temperature, and idles for little while then quits, and smells like gas. Idle speed fluctuated and surged up and down...


PO171 and P1131 point to lean codes on bank PO174 and P1151 point to lean code on bank PO305 is missfire on cyl 5

the lean codes is probably a vacuum leak or maybe a MAF sensor is bad or dirty

missfire is dependant on engine if a V10 it may be a coil actually pretty likely on the modulars not uncommon thats for sure
sorry forgot to add that its says missfire on #5 cant remember if that one is the first on the left or last on the left facing the engine vacummn leak could be those dang auto hubs got it stuck in the mud and they did not engage I need to buy some new ones took them apart to clean them out this summer

Dec 16, 2013 | 1999 Ford Contour

2 Answers

Ford f150 2003 po171 always lean bank 1. replaced bank 1 o2 sensor smoked intake. replaced egr valve. still code po171 short term trim 0123 but long term trim is up bank 1 30 anb bank 2 is 27. idle is a...


Code Po171 indicates a lean condition on cylinder bank #1 of the engine. This is the drivers side of the engine. I would suggest replacing both front oxygen sensors as a pair to start. An oxygen sensor has a life span of about 5 years and yours are now 9 years old if they are original. When they get older they are slow to respond to changes in the oxygen content of the exhaust and can trigger a code Po171. If you continue to have the same code set after the replacement of both oxygen sensors then it is time to find out why your engine is running lean. Some of the most common causes are an ignition misfire and a vacuum leak. I have also seen Fords EGR flow sensor (known by Ford as Delta Pressure Feedback sensor) to cause problems like that as well. A good mechanic with a scan tool can usually spot a problem like that in a few minutes.

Mar 01, 2011 | Ford F-150 Cars & Trucks

1 Answer

Check engine light is on codes are po171 system too lean (bank 1) po174 system too lean (bank 2) so what can i do


Look for vacuum leaks,that are causing the O2 Sensors to go lean, and set codes on both banks

Nov 11, 2010 | 1997 Ford Expedition

1 Answer

Generic code PO171 system 2 lean bank 1 generic


This can be caused by a faulty mass air flow sensor

Jul 06, 2010 | 1999 Ford Taurus

2 Answers

A po171 code came on my scanner i need to know


system too lean in bank 1. clean your mass airflow sensor, replace fuel filter. iff all else fails check you fuel pump.

Nov 06, 2009 | 1998 Ford Contour

1 Answer

Code 171 Bank 1 too lean


well actually you cant clean the mass air flow,you usually ruin it when you clean it,it could be a bad maf or just crapy gas,not crappy enuff that the car doesnt run,but enuff it doesnt like the air/fuel mixture and is setting the light

Oct 10, 2009 | 1996 Chevrolet Blazer

2 Answers

What does engine fault code po171 system too lean bank 1 mean thanks


i think its the oxygen sensor (pre cat) in exhaust

Sep 23, 2008 | 2002 Nissan Altima

Not finding what you are looking for?
2001 Toyota Celica Logo

Related Topics:

430 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...