Question about 1998 Toyota Camry

1 Answer

Need diagram of how to remove clutch - 1998 Toyota Camry

Posted by on

  • hrthomson25 Apr 11, 2011

    thanks perkins also need diagram of transaxle removal

  • hrthomson25 Apr 11, 2011

    thanks perkins. also need diagam of transaxle removal

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 14,251 Answers

Clutch

Print
Adjustments

Hydraulic clutch actuating systems used in Toyota vehicles do not require adjustment.
REMOVAL & INSTALLATION
Camry, Camry Solara

need diagram of how to - perkins48_681.jpg Fig. Clutch component assembly-Camry shown, others similar .

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable from the battery. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
  3. Raise and safely support the vehicle.
  4. Remove the transaxle assembly from the vehicle.
  5. Matchmark the clutch cover to the flywheel.
  6. Loosen each set bolt 1 turn at a time until spring tension is released.
  7. Once the tension on the springs are released, remove the clutch pressure plate retaining bolts.
  8. Remove the clutch cover.
  9. Remove the clutch disc.
  10. Remove the retaining clip and withdraw the release bearing from the transaxle.
  11. Remove the release fork and boot assembly. To install:
    1. Using a suitable clutch disc alignment tool, install the clutch disc onto the flywheel.
    2. Position the clutch cover onto the flywheel and align the matchmarks.
    3. Install the clutch cover retaining bolts. Tighten the bolts in a crisscross pattern to 14 ft. lbs. (19 Nm).
    4. Lubricate the release fork pivot contact points and the release bearing, bearing hub and input shaft spline surfaces with a suitable molybdenum disulfide lithium based or multi-purpose grease.
    5. Install the boot, release fork, hub and bearing assemblies.
    6. Install the transaxle to the vehicle.
    7. Lower the vehicle and check the clutch is working properly.
    8. Connect the negative battery cable to the battery.
    9. perkins48_682.jpg

      Fig. Tighten the pressure plate bolts according to the sequence shown-Camry.


      perkins48_683.jpgDuralast/Clutch Set,part#NU31195-1,for 164.99 at AutoZone.

Posted on Apr 11, 2011

  • Thomas Perkins
    Thomas Perkins Apr 11, 2011

    Manual Transaxle Assembly

    Print
    REMOVAL & INSTALLATION
    Avalon, Camry and Camry Solara
    Before servicing the vehicle, refer to the precautions in the beginning of this section.
    Disconnect the negative battery cable. On vehicles equipped with an air bag, wait at least 90 seconds before proceeding.
    Remove the air cleaner assembly.
    If equipped with cruise control, remove the cruise control actuator.
    Remove the clutch release cylinder and tube clamp.
    Remove the starter.
    Disconnect the back-up light switch connector and ground strap.
    Disconnect the wires clamp.
    Remove the clips and washers that attach the transaxle control cables to the control levers. Remove the retaining clips and disconnect the transaxle control cables.
    Disconnect the speed sensor connector.
    Install a engine support fixture.
    Tie the steering gear housing to the engine support fixture with a cord.
    Raise the vehicle and support it safely.
    Remove the engine undercovers and the front wheels.
    Drain the fluid from the transaxle.
    Remove the left and right halfshafts. Disconnect the steering gear housing from the front suspension member as follows:
    Remove the 4 bolts.
    Remove the stabilizer bar bushing bracket.
    Remove the 2 set bolts and nuts.
    Disconnect the steering gear box from the suspension member and suspend it securely.


    Remove the exhaust pipe.
    Remove the stiffener plate.
    Disconnect the engine front mounting from the suspension member by removing the 2 bolts.
    Disconnect the engine rear mounting from the front suspension member by removing the 2 grommets and the 3 nuts.
    With a transaxle jack and block of wood, raise the transaxle and engine slightly and disconnect the left engine mounting.
    Disconnect the steering cooler pipe from the suspension member.
    Remove the 2 fender liner set screws. Disconnect the front suspension member as follows:
    Remove the 2 bolts and 4 nuts located on the outside of the brackets.
    Remove the 4 larger bolts holding the suspension member to the vehicle body.
    Remove the 2 front lower braces, rear braces, and the front suspension member. Remove the 6 transaxle mounting bolts from the engine.
    Lower the left side of the engine and remove the transaxle.
    Clean the mating surfaces of grease and dirt in preparation for reinstallation.


    To install:

    Move the transaxle into position so that the input shaft spline is aligned with the clutch disc.
    Install the transaxle into the engine and secure with the lower mounting bolts. Tighten the 10mm mounting bolts to 47 ft. lbs. and 12mm bolts to 34 ft. lbs. (46 Nm).
    Install the front suspension member to the vehicle and install the 2 front lower braces and rear lower braces. Install the 4 large bolts that hold the suspension member to the vehicle. Tighten the bolts to 134 ft. lbs. (181 Nm).
    Install the 2 outside bolts and 4 outside nuts. Tighten the bolts to 24 ft. lbs. (32 Nm). Install the 2 fender liner set screws.
    Connect the steering cooler pipe to the suspension member.
    Raise the transaxle and engine slightly with a jack and wooden block.
    Install the engine left mounting as follows:
    Install the engine left mounting, then install the 3 bolts. Tighten the bolts to 38 ft. lbs. (52 Nm).
    Install the 2 nuts and 2 grommets. Tighten the nuts to 59 ft. lbs. (80 Nm).


    Install the engine rear mounting to the front suspension member by installing the 3 nuts and 2 grommets. Tighten the nuts to 59 ft. lbs. (80 Nm).
    Install the engine front mounting to the suspension member and install the nut and 2 bolts. Tighten the bolt to 59 ft. lbs. (80 Nm).
    Install the stiffener plate and tighten the bolts to 27 ft. lbs. (37 Nm).
    Install the exhaust pipe.
    Install the steering gear housing to the front suspension member as follows:Lower the steering gear housing onto the suspension member.
    Install the 2 set bolts and nuts. Tighten the bolts and nuts to 134 ft. lbs. (181 Nm).
    Install the stabilizer bar bushing bracket.
    Install the 4 bolts and tighten to 14 ft. lbs. (19 Nm).


    Install the right and left halfshafts.
    Install the engine undercovers.
    Install the wheels and lower the vehicle.
    Fill the transaxle with transaxle fluid.
    Untie the steering gear housing from the engine support fixture.
    Remove the engine support fixture from the vehicle.
    Connect the vehicle speed sensor.
    Connect the control cables by installing the washers and clips.
    Connect the clamp that retains the wires to the transaxle.
    Connect the back-up light switch connector and ground cables.
    Install the starter to the vehicle and install the 2 bolts. Tighten the bolts to 29 ft. lbs. (39 Nm). Install the pipe clamp and clutch release cylinder to the transaxle. Tighten the bolts to 108 inch lbs. (13 Nm).
    Install the cruise control actuator.
    Install the air cleaner case assembly.
    Connect the negative battery cable to the battery. I have pictures but nowhere on this page to send.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a diagram for clutch linkage for 1966 chevy impala


Its pretty simple set up, you go from the pedal assembly to the rod in the back down to the frame rocker, the linkage from the frame rocker to the clutch fork, you will also have a return spring there

Jan 08, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

I need a diagram of the clutch removal and installation for a 2003 pontiac Vibe... Does anyone have one they can post??


u need a repair manual sold at parts store or viewed at ur library--thats a task for pros-special tools and safety required--make sure clutch is the issue

Sep 27, 2011 | 2003 Pontiac Vibe

1 Answer

I need a diagram to show me how to remove the clutch from the air conditioning compressor for a 1997 for ecsort


Hi, here is a video on how to remove A/C clutch, most are similar. Please rate this answer if it helped! Thanks, Mike
http://www.youtube.com/watch?v=URqFd3KkSRY&feature=related

Jun 14, 2011 | 1997 Ford Escort

1 Answer

How do you remove a fan clutch and i need a diagram for 3.9 engine timing assembly


The distributor is for injector timing ,don't move it

Ignition timing is controlled by the computer

The fan clutch may be 36mm or 1/7/16" Wrench,
you need for the big nut

Dec 14, 2010 | 1996 Dodge Dakota

1 Answer

How do you remove the air conditioning pressure switch? we are trying to charge the a/c but need to keep the compressor running and can't figure out how to remove this switch to "jump" it.


Hi!

I always jump the relayi instead of the sensor, it is easier and don't run the chance to screw up the sensor.

Look for the fuse box in the engine compartment, usually by the battery, take the cover off and look inside, there is a diagram with the location of the fuses and relays, look for the A/C Clutch Relay, (it may not say Clutch in it), look at the diagram in the relay to see which terminals are for the load and which are the ones to activate the coil, turn the key in the Ignition to the "Run" positiion, insert a piece of wire in the holes between the load terminals(usually are 86 and 30), no need to insert relay back, you should hear a click coming from the compressor clutch been activated. Remove Jumper and replace Relay when done working on A/C compressor;

Don't forget to rate this post. Good Luck!!!

May 24, 2010 | 2004 Honda Accord

1 Answer

Need diagram of routing for the clutch cable


check connection at or right before clutch connection point

Oct 04, 2009 | Volkswagen Cabriolet Cars & Trucks

1 Answer

Removing the a/c compressor from a 1990 seville


release tension on drive belt - bolts are inline with the body of compressor behind the pulley - freon hoses need to be unbolted -freon if it still as any needs to be recovered - r12 - the clutch is in place with snap -ring on front of compressor shaft - behind center nut - special tool to pull off clutch

Sep 24, 2009 | 1990 Cadillac SeVille

1 Answer

Need a diagram of the clutch bearing in order to take it apart from vehicle.The 1996 Isuzu Troper repair book we have does show an inside view and we cannot get this piece off.


I cant send a diagram but I can explain how. To remove the unit from the clutch arm. The unit is held in with a spring clip pull the bearing out and you will see where the spring clip is holding they are pull one end of the spring down and over the flange which is holding it and the other end up the unit will slide off. To remove the bearing from the unit clamp the outside of the bearing in a vice and with a socket and hammer tap out the cast iron center. The clutch arm is also held in with a spring clip over a ball in the bell housing a quick firm pull will take it off if needed.

Sep 09, 2009 | 1995 Isuzu Trooper

1 Answer

How to change a hydrolic clutch on a 2008 ford mustang 4.0 diagrams, or pictures please


Ummm you don't,
the clutch has to have the transmision removed to replace, but you leave the HYDRAULIC part on
It doesn't even need djustment

Sep 01, 2009 | 2008 Ford Mustang

1 Answer

How do you replace a audi A6 clutch


A chiltons manual or something similar is your best bet. This is beyond a diagram, allot of steps are needed to remove the clutch inside the transmisson, and allot of parts should be replaced along the way.

Nov 01, 2008 | 2002 Audi A6

Not finding what you are looking for?
1998 Toyota Camry Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...